IKEA SMUSSLA bedside table/shelf unit assembly instructions
How to assemble the IKEA SMUSSLA bedside table/shelf unit (nightstand), step by step: 17 animated steps built from the official manual, about 30–45 min for 1 person, with Allen key 100006 (included), Z-key 100002 (included).
White children’s bedside table and shelf unit: a dowelled box with a slide-in divider and shelf held by wire supports, four legs and soft caps. Size: 51×32×43 cm (horizontal, on legs). About 30–45 min, 1 person. Tools: Allen key 100006 (included), Z-key 100002 (included).
Based on the official IKEA manual AA-2230202-2 (PDF). Guide updated .
| Steps | 17 |
|---|---|
| Time | 30–45 min |
| People | 1 |
| Tools | Allen key 100006 (included), Z-key 100002 (included) |
| Size | 51×32×43 cm (horizontal, on legs) |
| Official manual | AA-2230202-2 |
| IKEA article number | 904.694.89 (white) |
| Pieces in the box | 66 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Back panel | 1 | |
| Side panel | 2 | |
| Top / bottom panel | 2 | |
| Divider | 1 | |
| Shelf | 1 | |
| Screw | 100224 | 8 |
| Dowel | 101375 | 16 |
| Threaded stud | 100042 | 4 |
| Connector bolt | 100600 | 4 |
| Cap screw | 10058747 | 8 |
| Large cap | 10058759 | 1 |
| Cap | 10058746 | 8 |
| Wire support | 190090 | 4 |
| Leg | 10059435 | 4 |
| Z-key | 100002 | 1 |
| Allen key | 100006 | 1 |
Steps
- Dowels into the boards — Lay the five boards on a rug, inner faces up. Push the 16 dowels (101375) into the edge holes: 2 in each edge of the back panel and 2 in each end edge of both side panels.
- Left side onto the back — Tip the left side panel up and push it onto the dowels in the left edge of the back panel, with its dowels pointing up and down along the back.
- Right side onto the back — Tip the right side panel up the same way and push it onto the dowels in the right edge of the back panel.
- Top panel on the far side — Tip up the panel on the far side (the top) and push it onto the dowels of the back panel and of both sides.
- Bottom panel on the near side — Tip up the panel with the most holes (the bottom, where the legs go) on the near side and push it onto the remaining dowels. The box now stands open-side up.
- Screw the bottom panel — Screw 4 screws (100224) through the bottom panel into the ends of the side panels, 2 at each end. Tighten clockwise with the Allen key (100006).
- Screw the top panel — Turn to the far side and screw the other 4 screws (100224) through the top panel into the side panels the same way.
- Wires for the divider — Hook a wire (190090) into the two holes on the inside of the top panel and another into the matching holes on the inside of the bottom panel, about a third of the way from the right.
- Slide in the divider — Push the divider straight down between the top and bottom panels, with the grooves in its edges over the two wires, until it rests on the back panel.
- Wires for the shelf — Hook a wire (190090) into the two holes in the middle of the left side panel and another into the matching holes on the divider, both facing into the wide compartment.
- Slide in the shelf — Push the shelf straight down into the wide compartment, with the grooves in its ends over the two wires, until it rests on the back panel.
- Studs into the connector bolts — By hand, screw a threaded stud (100042) into each of the 4 connector bolts (100600) as far as it goes.
- Fit the legs — Hold a leg (10059435) against a corner hole of the bottom panel, put a connector bolt through from inside and tighten it into the leg with the Z-key (100002). Fit all 4 legs. Check: The unit can also stand on its end or as an open box (see the manual’s info drawings); this guide shows the low bedside table.
- Stand it up, large cap — Stand the unit on its legs. Hold the large cap (10058759) on the hole at the top front corner of the left side, then from inside screw a cap screw (10058747) into it with the Z-key.
- Caps on the back and left side — Hold a cap (10058746) on each of the 7 remaining holes: 4 at the corners of the back and 3 at the other corners of the left side. One cap is a spare.
- Cap screws from inside — From inside, screw a cap screw (10058747) through each hole into its cap and tighten it with the Z-key (100002).
- Done! — Your SMUSSLA bedside table/shelf unit is ready.
SMUSSLA bedside table/shelf unit: questions and answers
How long does it take to assemble the IKEA SMUSSLA bedside table/shelf unit?
About 30–45 min for 1 person, working through the 17 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the SMUSSLA bedside table/shelf unit?
Allen key 100006 (included), Z-key 100002 (included). Already in the box: Allen key 100006, Z-key 100002.
Can one person assemble the SMUSSLA bedside table/shelf unit?
Yes, it is a one-person build.
What size is the SMUSSLA bedside table/shelf unit once assembled?
51×32×43 cm (horizontal, on legs), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the SMUSSLA bedside table/shelf unit?
58 fittings of 10 kinds, the most numerous being 16 × dowel, 8 × screw, 8 × cap screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA SMUSSLA bedside table/shelf unit assembly instructions PDF?
The official PDF is manual AA-2230202-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 904.694.89 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2230202-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 100224). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
- IKEA STORKLINTA chest of 2 drawers assembly instructions
All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained