Step by StepAssembly Find your furniture

IKEA ENHET wall frame with shelves assembly instructions

How to assemble the IKEA ENHET wall frame with shelves, step by step: 18 animated steps built from the official manual, about 30–45 min for 1 person, with flat-blade screwdriver, pencil, spirit level, drill, wall screws and plugs (not included).

IKEA ENHET wall frame with shelves, assembled

An anthracite powder-coated steel wall frame: two side frames joined by six clip-in tubes, three shelf trays, hung on two wall screws through corner brackets. Size: 40x15x75 cm. About 30–45 min, 1 person. Tools: Flat-blade screwdriver, Pencil, Spirit level, Drill, Wall screws and plugs (not included).

Based on the official IKEA manual AA-2371924-4 (PDF). Guide updated .

ENHET wall frame with shelves: quick facts
Steps18
Time30–45 min
People1
ToolsFlat-blade screwdriver, Pencil, Spirit level, Drill, Wall screws and plugs (not included)
Size40x15x75 cm
Official manualAA-2371924-4
IKEA article number304.489.37 (anthracite)
Pieces in the box37

In the box

PartPart numberQuantity
Side frame2
Cross tube6
Shelf3
End cap100455398
Rail holder100455384
Shelf clip100698936
Joining clip 10044491 (only to join two frames)2
Corner bracket I100497761
Corner bracket II100497771
Bracket cover100497712
U-clip100497752

Steps

  1. Corner brackets onto the side frames — Lay both side frames flat on a soft surface, holes facing up. Press corner bracket I (10049776) into the 2 slots at one end of the first frame and slide it towards the end until it locks. Do the same with bracket II (10049777) on the second frame. Check: Check the I and II marks on the brackets: each one fits only its own frame.
  2. Rail holders into the long tubes — Push a rail holder (10045538) into the slot halfway along each of the 4 long tubes. Slide an end cap (10045539) over each holder to press it fully home, then take the cap off again: it is used later.
  3. First cross tube and end cap — On the frame with bracket I, stand a cross tube in the hole next to the bracket, slot towards the bracket, slide it onto the bracket hook and press it down. Then push an end cap (10045539) into the open end of the long tube to lock the cross tube in.
  4. Three more cross tubes — Stand the other 3 cross tubes in the remaining holes of the same side frame, one in each corner, and press them down. Lock each one with an end cap (10045539) pushed into the open end of the long tube.
  5. Second side frame on top — Turn the frame with bracket II over and lower it onto the 4 upright tubes, bracket towards the bracket of the bottom frame, so the tube ends go into its holes. Slide it so bracket II hooks onto the cross tube, then press it down.
  6. Four end caps on top — Push an end cap (10045539) into each of the 4 open tube ends of the upper side frame.
  7. Stand it up on the bracket end — Tip the frame up so it stands on the end with the corner brackets, on a soft surface such as the flattened carton.
  8. Press the caps home — Press down firmly on the top of the frame. The 4 end caps underneath are pushed fully into the tubes until they sit flush. Check: Press on the middle of the top, so all 4 caps go in straight.
  9. Turn it the right way up — Lift the frame, turn it over so the corner brackets are at the top, and stand it back down on its other end.
  10. Press the other caps home — Press down on the top of the frame again, so the other 4 end caps are pushed fully into the tubes.
  11. Click in the middle tubes — Put the last 2 cross tubes in halfway up, one at the back and one at the front. Lower each end onto its rail holder and press down until it clicks.
  12. Level it on the wall, mark the holes — Hold the frame against the wall where it will hang, brackets at the top. Lay a spirit level on top and adjust until it is level, then mark the wall with a pencil through the hole in each corner bracket. Check: Screws and plugs for the wall are not included. Choose ones that suit your wall.
  13. Screws into the wall — Put the frame aside. Drill a hole at each mark, push in wall plugs that suit your wall, and drive in 2 pan-head screws, leaving each head about 1.5 cm out of the wall. Check: Use screws with a flat underside to the head (pan head), not countersunk screws.
  14. Shelves in, clips on — Lay a shelf on the top, middle and bottom level of the frame, so it rests on the cross bars of the side frames between the tubes. Lock each shelf with 2 clips (10069893), one at each end, pushed in towards the front.
  15. Hang it, fit the U-clips, tighten — Lift the frame and hang it with the holes in the corner brackets over the 2 screw heads. Slide a U-clip (10049775) behind each screw head, check with the spirit level and adjust, then tighten both screws.
  16. Bracket covers — Click a cover (10049771) over each corner bracket, pushing it straight back from the front.
  17. Info: joining two frames — Only when a second ENHET frame hangs right next to this one: click the 2 joining clips (10044491) over the two front tubes where the frames meet, one higher up and one lower down.
  18. Done! — Your ENHET wall frame hangs level on the wall with its 3 shelves. Max load: 3 kg per shelf, spread evenly.

ENHET wall frame with shelves: questions and answers

How long does it take to assemble the IKEA ENHET wall frame with shelves?

About 30–45 min for 1 person, working through the 18 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the ENHET wall frame with shelves?

Flat-blade screwdriver, pencil, spirit level, drill, wall screws and plugs (not included).

Can one person assemble the ENHET wall frame with shelves?

Yes, it is a one-person build.

Does the ENHET wall frame with shelves need to be fixed to the wall?

The manual shows a wall fixing: see step 12 (Level it on the wall, mark the holes) and step 13 (Screws into the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the ENHET wall frame with shelves once assembled?

40x15x75 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the ENHET wall frame with shelves?

24 fittings of 7 kinds, the most numerous being 8 × end cap, 6 × shelf clip, 4 × rail holder. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA ENHET wall frame with shelves assembly instructions PDF?

The official PDF is manual AA-2371924-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 304.489.37 (anthracite); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2371924-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example end cap 10045539). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained