Step by StepAssembly Find your furniture

IKEA LÄTT children's table with 2 chairs assembly instructions

How to assemble the IKEA LÄTT children's table with 2 chairs, step by step: 25 animated steps built from the official manual, about 30–45 min for 1 person, with Allen key (included).

IKEA LÄTT children's table with 2 chairs, assembled

A small pine-and-white table with two matching chairs for children: every piece is a frame of slot-together rails held by 4 bolts, with the white top or seat sliding into grooves. Size: Table 63×48×45 cm; chairs: seat 28×28 cm, seat height 28 cm. About 30–45 min, 1 person. Tools: Allen key (included).

Based on the official IKEA manual AA-114934-7 (PDF). Guide updated .

LÄTT children's table with 2 chairs: quick facts
Steps25
Time30–45 min
People1
ToolsAllen key (included)
SizeTable 63×48×45 cm; chairs: seat 28×28 cm, seat height 28 cm
Official manualAA-114934-7
IKEA article number501.784.11 (white pine)
Pieces in the box52

In the box

PartPart numberQuantity
Table top (white)1
Table leg frame2
Table end rail2
Chair seat (white)2
Chair front frame2
Chair back frame2
Chair side rail4
Wooden dowel10135012
Barrel nut10051412
Bolt10511712
Allen key1000011

Steps

  1. Table: dowels into the side rails — Lay the two grooved end rails of the table flat with the groove facing up. Push a wooden dowel (101350) into the hole in each end, 4 in total.
  2. Table: rails onto the leg frame — Stand the first leg frame upside down, apron on the floor and legs pointing up. Stand the rails on edge, grooves facing each other, and push their dowels into the holes next to the legs.
  3. Table: barrel nut and bolt, first side — Drop a barrel nut (100514) into the hole on the inside of the rail and turn its slot so it points along the rail. Push a bolt (105117) through the leg into the rail and screw it into the barrel nut with the allen key (100001). Check: Leave the bolts a little loose for now: you tighten all of them at the end.
  4. Table: barrel nut and bolt, other side — Do the same on the other rail: barrel nut into the inside hole, slot turned along the rail, then the bolt through the leg, screwed in loosely with the allen key. Check: Still loose: you tighten everything at the end.
  5. Table: slide in the table top — Stand the table on that frame, legs pointing towards you. Slide the white table top down into the grooves of the rails until it rests in the groove of the frame.
  6. Table: second leg frame on top — Put the second leg frame on top, legs pointing the same way as the first, and press its holes onto the dowels.
  7. Table: barrel nut and bolt on top, first side — Fit another barrel nut into the hole on the inside of a rail, slot along the rail. Push a bolt down through the leg frame's leg into it and screw it in with the allen key. Check: Again only loosely, so the parts can still settle.
  8. Table: barrel nut and bolt on top, other side — The last barrel nut goes into the other rail, and the last bolt down through the other leg of the leg frame, again only loosely.
  9. Table: stand it up and tighten 2 bolts — Turn the table onto its legs. Press down on the table top with both hands so it sits right down in its grooves, then tighten the 2 bolts on this side firmly with the allen key. Check: Tighten until each bolt head sits flush against the leg, with no gap.
  10. Table: tighten the other 2 bolts — Turn the table round so the other 2 bolts face you, and tighten them the same way until the heads sit flush.
  11. First chair: dowels into the side rails — Lay the two grooved side rails of a chair flat with the groove facing up. Push a wooden dowel (101350) into the hole in each end, 4 in total.
  12. First chair: rails onto the front frame — Stand the front frame (the one with the short legs) upside down, apron on the floor and legs pointing up. Stand the rails on edge, grooves facing each other, and push their dowels into the holes next to the legs.
  13. First chair: barrel nut and bolt, first side — Drop a barrel nut (100514) into the hole on the inside of the rail and turn its slot so it points along the rail. Push a bolt (105117) through the leg into the rail and screw it into the barrel nut with the allen key (100001). Check: Leave the bolts a little loose for now: you tighten all of them at the end.
  14. First chair: barrel nut and bolt, other side — Do the same on the other rail: barrel nut into the inside hole, slot turned along the rail, then the bolt through the leg, screwed in loosely with the allen key. Check: Still loose: you tighten everything at the end.
  15. First chair: slide in the seat — Stand the chair on that frame, legs pointing towards you. Slide the white seat down into the grooves of the rails until it rests in the groove of the frame.
  16. First chair: back frame on top — Put the back frame (the one with the backrest) on top, legs pointing the same way as the front legs, and press it onto the dowels.
  17. First chair: barrel nut and bolt on top, first side — Fit another barrel nut into the hole on the inside of a rail, slot along the rail. Push a bolt down through the back frame's leg into it and screw it in with the allen key. Check: Again only loosely, so the parts can still settle.
  18. First chair: barrel nut and bolt on top, other side — The last barrel nut goes into the other rail, and the last bolt down through the other leg of the back frame, again only loosely.
  19. First chair: stand it up and tighten 2 bolts — Turn the chair onto its legs. Press down on the seat with both hands so it sits right down in its grooves, then tighten the 2 bolts on this side firmly with the allen key. Check: Tighten until each bolt head sits flush against the leg, with no gap.
  20. First chair: tighten the other 2 bolts — Go round to the front of the chair and tighten the last 2 bolts the same way. Then put the chair by the table.
  21. Second chair: rails, front frame and first bolts — Build the second chair the same way (manual steps 1–3): 4 dowels into the side rails, rails onto the upside-down front frame, 2 barrel nuts and 2 loose bolts.
  22. Second chair: seat, back frame and 2 bolts — Manual steps 4–6: stand it on the front frame, slide the seat into the grooves, press the back frame onto the dowels and fit the last 2 barrel nuts and bolts, loosely.
  23. Second chair: stand it up and tighten 2 bolts — Turn the chair onto its legs, press the seat down and tighten the 2 bolts on this side with the allen key until the heads sit flush.
  24. Second chair: the other 2 bolts — Tighten the last 2 bolts at the front of the chair, then put it by the table.
  25. Done! — The table and both chairs are ready. Check the bolts now and then and tighten them again if a piece starts to wobble.

LÄTT children's table with 2 chairs: questions and answers

How long does it take to assemble the IKEA LÄTT children's table with 2 chairs?

About 30–45 min for 1 person, working through the 25 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the LÄTT children's table with 2 chairs?

Allen key (included). Already in the box: Allen key.

Can one person assemble the LÄTT children's table with 2 chairs?

Yes, it is a one-person build.

What size is the LÄTT children's table with 2 chairs once assembled?

Table 63×48×45 cm; chairs: seat 28×28 cm, seat height 28 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the LÄTT children's table with 2 chairs?

36 fittings of 3 kinds, the most numerous being 12 × wooden dowel, 12 × barrel nut, 12 × bolt. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA LÄTT children's table with 2 chairs assembly instructions PDF?

The official PDF is manual AA-114934-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 501.784.11 (white pine); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-114934-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example wooden dowel 101350). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained