Step by StepAssembly Find your furniture

IKEA BESTÅ TV bench assembly instructions

How to assemble the IKEA BESTÅ TV bench, step by step: 25 animated steps built from the official manual, about 1–1.5 hours for 2 people, with flat screwdriver, Phillips screwdriver, spirit level, Allen key (included).

IKEA BESTÅ TV bench, assembled

Long, low BESTÅ TV bench with three open compartments: a cam-lock frame built upside down, two back panels with a cable opening in the middle, adjustable feet and wall fixing. Size: 180×40×38 cm (70 7/8×15 3/4×15"). About 1–1.5 hours, 2 people. Tools: Flat screwdriver, Phillips screwdriver, Spirit level, Allen key (included).

Based on the official IKEA manual AA-1402080-13 (PDF). Guide updated .

BESTÅ TV bench: quick facts
Steps25
Time1–1.5 hours
People2
ToolsFlat screwdriver, Phillips screwdriver, Spirit level, Allen key (included)
Size180×40×38 cm (70 7/8×15 3/4×15")
Official manualAA-1402080-13
IKEA article number004.740.70 (white)
Pieces in the box103

In the box

PartPart numberQuantity
Top panel (with groove, no foot holes)1
Bottom panel (with foot holes)1
Side panel2
Divider2
Back panel2
Cable cover panel1
Cam screw13061816
Cam lock1181378
Cam lock1306198
Foot1149478
Wall bracket1443424
Screw1132878
Keyhole plate1036934
Bracket cover1443434
H-profile1443482
Cable trim1332031
Cable trim1445671
Screw1090494
Cable rail1332091
Shelf support1154446
Shelf support1154436
Screw11663712
Allen key1000061

Steps

  1. Feet into the bottom panel — Lay the top and bottom panels flat on a rug. The top panel has the groove and no foot holes. Screw the 8 feet (114947) into the 8 holes of the bottom panel by hand. Check: Hanging the bench on the wall instead? Then leave the feet off (manual p21). Work on a soft surface so the panels do not get scratched.
  2. Turn the bottom panel over, cam screws in — Turn the bottom panel over so it stands on its feet. Screw 8 cam screws (130618) into the holes on the inner face of each panel with a Phillips screwdriver. Check: Do not use a power drill.
  3. Wall brackets on the side panels — Lay both side panels flat, pin holes up. Screw a wall bracket (144342) onto each with 2 screws (113287): at the top end, next to the cam-lock hole, its flange flush with the grooved back edge.
  4. Side panels onto the top panel — The frame is built upside down. Stand the side panels on the ends of the top panel, brackets down and towards you, so the cam screws go into their holes.
  5. Lock the side panels: 4 cam locks — Push a cam lock (118137) into each hole next to the top panel, arrow towards the cam screw, and turn it clockwise with a flat screwdriver until it grips. Check: Use the plain cam locks 118137 here, not the ribbed 130619.
  6. Wall brackets on the dividers — Lay the 2 dividers flat. Screw a wall bracket (144342) onto each with 2 screws (113287), next to the cam-lock hole at the back edge, on the face with the cam-lock holes. Both brackets face the middle compartment.
  7. Dividers onto the top panel — Stand the dividers on the top panel over the middle cam screws, brackets down and towards you, both facing the middle compartment.
  8. Lock the dividers: 4 cam locks — Push the ribbed cam locks (130619) into the dividers from the middle compartment, next to the top panel, and turn each clockwise with a flat screwdriver. Check: Use the ribbed cam locks 130619 in the dividers, not 118137.
  9. Slide in the back panels — Slide the 2 back panels down into the grooves of the side panels and the top panel, notches over the brackets. They leave a gap in the middle for cables.
  10. Bottom panel onto the frame — Turn the bottom panel over, feet up, and lower it onto the frame so the cam screws go into the side panels and dividers and the back panels go into its groove.
  11. Lock the bottom panel: 8 cam locks — From the open front, push in the last cam locks next to the bottom panel: 4 ribbed 130619 in the dividers and 4 plain 118137 in the side panels. Turn each clockwise.
  12. Roll it onto its front, H-profiles in — Carefully roll the frame onto its front, back facing up. Slide the 2 H-profiles (144348) onto the inner edges of the back panels, from the bottom panel end.
  13. Cable cover panel — Slide the cable cover panel into the H-profiles from the bottom panel end and push it in until it stops. The opening above it is for your cables.
  14. Cable trims in the notches — Put the trim with the clip slot (133203) into the notch of the top panel and the plain trim (144567) into the notch of the bottom panel. Fix each with 2 screws (109049).
  15. Stand it up, run the cables — Stand the bench up on its feet. Run your TV cables in through the opening at the back: down through the notch in the top panel and above the cover panel into the compartment.
  16. Click on the cable rail — Hook one end of the cable rail (133209) into the trim over the cables, then press the other end down until both ends click into place.
  17. Level the end feet with the allen key — Put the bench where it will stand, against the wall. Check it with a spirit level and adjust the 4 feet in the end compartments from inside, with the allen key (100006) through the holes in the bottom panel.
  18. Level the middle feet by hand — Turn the 4 feet under the dividers by hand until they all rest firmly on the floor and the bench is level.
  19. Screws into the wall — Mark the wall behind the 4 bracket holes (80 mm under the top). Pull the bench away, put in 4 wall screws with a round head that suit your wall, heads 1 cm out, then push the bench back so the heads go through the brackets. Check: Must be fixed to the wall to prevent tip-over. Wall screws and plugs are not included: ask a specialist if unsure what suits your wall.
  20. Keyhole plates on, tighten the screws — In each bracket, put a keyhole plate (103693) over the screw head and slide it down so the narrow slot holds the screw. Adjust the bench, then tighten the screw.
  21. Click on the bracket covers — Push a cover (144343) onto each of the 4 wall brackets until it clicks.
  22. Optional: shelf supports, left compartment — For an extra BESTÅ shelf (sold separately): screw 4 shelf supports into the pin holes of a compartment, each with a screw (116637): 115444 on the left wall, 115443 on the right wall. Then lower the shelf onto them.
  23. Optional: shelf supports, middle compartment — The same in the middle compartment: 2 supports 115444 on the left wall, 2 supports 115443 on the right wall, one screw 116637 each.
  24. Optional: shelf supports, right compartment — The same in the right compartment: 2 supports 115444 on the left wall, 2 supports 115443 on the right wall, one screw 116637 each.
  25. Done! — Your BESTÅ TV bench is finished and fixed to the wall. It takes a TV of up to 30 kg. Doors and drawers are sold separately.

BESTÅ TV bench: questions and answers

How long does it take to assemble the IKEA BESTÅ TV bench?

About 1–1.5 hours for 2 people, working through the 25 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BESTÅ TV bench?

Flat screwdriver, Phillips screwdriver, spirit level, Allen key (included). Already in the box: Allen key.

Can one person assemble the BESTÅ TV bench?

It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 10 and 15, where the furniture is lifted or turned.

Does the BESTÅ TV bench need to be fixed to the wall?

The manual shows a wall fixing: see step 3 (Wall brackets on the side panels) and step 6 (Wall brackets on the dividers). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BESTÅ TV bench once assembled?

180×40×38 cm (70 7/8×15 3/4×15"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the BESTÅ TV bench?

93 fittings of 16 kinds, the most numerous being 16 × cam screw, 12 × screw, 8 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BESTÅ TV bench assembly instructions PDF?

The official PDF is manual AA-1402080-13, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 004.740.70 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1402080-13. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 130618). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA BESTÅ assembly guides · All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained