IKEA STRANDMON wing chair assembly instructions
How to assemble the IKEA STRANDMON wing chair, step by step: 17 animated steps built from the official manual, about 30–45 min for 1 person, with box spanner 120202 (included), Phillips screwdriver.
Upholstered wing chair: the seat frame bolts onto the backrest, four wooden legs screw in, and two arm-and-wing panels hook onto the backrest and bolt to the seat. Size: 82×96 cm, 101 cm high, seat height 45 cm (32 1/4×37 3/4×39 3/4"). About 30–45 min, 1 person. Tools: Box spanner 120202 (included), Phillips screwdriver.
Based on the official IKEA manual AA-2019535-9 (PDF). Guide updated .
| Steps | 17 |
|---|---|
| Time | 30–45 min |
| People | 1 |
| Tools | Box spanner 120202 (included), Phillips screwdriver |
| Size | 82×96 cm, 101 cm high, seat height 45 cm (32 1/4×37 3/4×39 3/4") |
| Official manual | AA-2019535-9 |
| IKEA article number | 506.289.42 (talliden beige brown) |
| Pieces in the box | 36 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Backrest | 1 | |
| Seat frame | 1 | |
| Arm and wing panel | 2 | |
| Seat cushion | 1 | |
| Back leg 131290 (shorter) | 2 | |
| Front leg 131289 (longer) | 2 | |
| Stud | 114509 | 2 |
| Nut | 100712 | 2 |
| Washer | 100837 | 6 |
| Large washer | 108014 | 4 |
| Bolt | 131128 | 4 |
| Hook bracket | 150022 | 2 |
| Screw | 101084 | 2 |
| Glide 10081375 (2 sheets of 2) | 4 | |
| Box spanner | 120202 | 1 |
Steps
- Backrest face up, twist in the 2 studs — Lay the backrest face up on a soft surface, its bottom rail towards you. Twist a stud (114509) clockwise by hand into each of the 2 holes in the front of the rail until about half of it is in. Check: Work on a rug or the flattened box so the fabric is not damaged.
- Put the seat frame on the studs — Hold the seat frame upright, springs towards you and its padded front edge at the top. Lower it so the 2 studs go through the holes in its back rail and the rail rests on the backrest rail.
- Washers and nuts on the studs — From the spring side, put a washer (100837) and a nut (100712) on each stud. Tighten both nuts clockwise with the box spanner (120202).
- Screw on the 2 back legs — Roll the chair onto its side, underside towards you. Put a large washer (108014) over each hole at the back corners of the seat frame and screw the 2 shorter legs (131290) in clockwise by hand. Check: The back legs are the shorter ones (131290). Check the length before you screw them in.
- Turn it over, front legs on, stand it up — Turn the chair over onto its other side. Put a large washer (108014) over each hole at the front corners and screw the 2 longer legs (131289) in clockwise by hand. Then stand the chair up on its legs.
- Hook brackets on the arm panels — Lay both arm panels flat, inside face up. Screw a hook bracket (150022) to each one near the top of the wing with a screw (101084), hook pointing up, using a Phillips screwdriver.
- Hook the first arm onto the backrest — Stand the arm with the hook up next to the left side of the chair (left when you sit in it). Slide it against the seat and backrest so the hook goes into the slot in the side of the backrest.
- Press the arm down — Press down on the top of the wing until the hook drops into the slot and the arm sits on the floor level with the seat frame. The top of the wing should line up with the top of the backrest. Check: The arm must sit right up against the backrest, with no gap at the top.
- Put in the 2 bolts by hand — Tip the chair onto its other side, fitted arm up. From inside the seat frame, put a washer (100837) on each of 2 bolts (131128) and screw them by hand through the side rail into the arm. Leave them a little loose. Check: Do not tighten yet: the arm must still line up flush with the backrest.
- Tighten the bolts, stand it up — Check that the arm sits flush against the backrest at the top and the back. Then tighten both bolts clockwise with the box spanner (120202) and stand the chair up.
- Hook the second arm onto the backrest — Stand the second arm with its hook up next to the right side of the chair. Slide it against the seat and backrest so the hook goes into the slot in the side of the backrest.
- Press the second arm down — Press down on the top of the wing until the hook drops into the slot and the arm sits level with the seat frame. The top of the wing should line up with the top of the backrest. Check: The arm must sit right up against the backrest, with no gap at the top.
- Put in the other 2 bolts by hand — Tip the chair onto its first arm, the new arm up. From inside the seat frame, put a washer (100837) on each of 2 bolts (131128) and screw them by hand through the side rail into the arm. Leave them a little loose. Check: Do not tighten yet: the arm must still line up flush with the backrest.
- Tighten the other 2 bolts — Check that the second arm sits flush against the backrest at the top and the back. Then tighten both bolts clockwise with the box spanner (120202).
- Press on the 4 glides — Break the 2 glide sheets (10081375) into 4 glides and press one onto the end of each leg.
- Stand it up, push in the seat cushion — Stand the chair up on its legs. Push the seat cushion in from the front until it sits against the backrest between the arms.
- Done! — Your STRANDMON wing chair is ready. If the chair starts to wobble after a while, tip it on its side and tighten the 4 arm bolts again with the box spanner.
STRANDMON wing chair: questions and answers
How long does it take to assemble the IKEA STRANDMON wing chair?
About 30–45 min for 1 person, working through the 17 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the STRANDMON wing chair?
Box spanner 120202 (included), Phillips screwdriver. Already in the box: Box spanner 120202.
Can one person assemble the STRANDMON wing chair?
Yes, it is a one-person build.
What size is the STRANDMON wing chair once assembled?
82×96 cm, 101 cm high, seat height 45 cm (32 1/4×37 3/4×39 3/4"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the STRANDMON wing chair?
22 fittings of 7 kinds, the most numerous being 6 × washer, 4 × large washer, 4 × bolt. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA STRANDMON wing chair assembly instructions PDF?
The official PDF is manual AA-2019535-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 506.289.42 (talliden beige brown); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2019535-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example back leg 131290). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BESTÅ TV bench assembly instructions
All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained