IKEA LOMMARP cabinet assembly instructions
How to assemble the IKEA LOMMARP cabinet, step by step: 58 animated steps built from the official manual, about 3–4 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, wall screws and plugs (not included).
A dark blue-green cabinet on a shaped plinth, with two panelled doors over a divider and four shelves, and a wide drawer underneath. Size: 102×50×101 cm. About 3–4 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Wall screws and plugs (not included).
Based on the official IKEA manual AA-2194723-5 (PDF). Guide updated .
| Steps | 58 |
|---|---|
| Time | 3–4 hours |
| People | 2 |
| Tools | Flat-blade screwdriver, Phillips screwdriver, Wall screws and plugs (not included) |
| Size | 102×50×101 cm |
| Official manual | AA-2194723-5 |
| IKEA article number | 804.154.68 (dark blue green) |
| Pieces in the box | 230 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Front apron | 1 | |
| Back apron | 1 | |
| Plinth side piece | 2 | |
| Plinth board | 1 | |
| Side panel | 2 | |
| Middle shelf | 1 | |
| Divider | 1 | |
| Back panel | 1 | |
| Top | 1 | |
| Shelf | 4 | |
| Door | 2 | |
| Drawer front | 1 | |
| Drawer side | 2 | |
| Drawer bottom | 1 | |
| Drawer back | 1 | |
| Support bar | 128765 | 1 |
| Drawer runner 125325 / | 125326 | 2 |
| Hinge | 10031762 | 2 |
| Hinge | 10031756 | 2 |
| Dowel | 101345 | 34 |
| Cam screw | 100481 | 16 |
| Screw | 100347 | 12 |
| Cam lock | 103430 | 32 |
| Angle bracket | 103717 | 4 |
| Foot pad A | 10006536 | 2 |
| Foot pad B | 10006543 | 2 |
| Cam screw | 118331 | 24 |
| Shelf support | 131372 | 16 |
| Plug | 151708 | 4 |
| Pin | 151707 | 4 |
| Clip | 10093081 | 8 |
| Cap | 10093082 | 8 |
| Cover cap | 133303 | 2 |
| Washer | 126916 | 2 |
| Wall bracket | 141413 | 2 |
| Spacer | 141414 | 2 |
| Screw | 119976 | 2 |
| Screw | 151743 | 2 |
| Screw | 105344 | 3 |
| Cam lock | 112399 | 8 |
| Bumper | 107586 | 6 |
| Handle | 10006275 | 2 |
| Knob | 10006309 | 2 |
| Lock clip | 124218 | 2 |
Steps
- Cam screws in the side pieces — Open bag 1. Lay the front apron and the two shaped side pieces flat on a soft surface, in a row. Screw 2 cam screws (100481) into each side piece, near the end that meets the apron, until the collar touches the wood. Check: Do not over-tighten: the collar must sit on the surface, not sink into it.
- Dowels in the front apron — Tap 2 wooden dowels (101345) into the holes in each end of the front apron.
- Swing the side pieces up — Swing both side pieces up so they stand on edge at the ends of the apron, then push them onto the dowels and cam screws.
- Lock the plinth frame — Press 4 cam locks (103430) into the apron next to the cam screws and turn each one clockwise to lock. Then turn the frame over onto its legs.
- Dowels on top of the frame — Tap 7 dowels (101345) into the holes along the top edge of the frame: 3 in the front apron and 2 in each side piece.
- Brackets on the back apron — Lay the plinth board upside down, the rounded edges at the front and sides. Lay the back apron flat, inner face up, and screw 4 angle brackets (103717) onto it near its ends with a screw (100347) each. Check: The board's rounded edge goes at the front and both sides.
- Dowels in the back apron — Tap 3 dowels (101345) into the holes in the long straight edge of the back apron.
- Cam screws in the plinth board — Screw 12 cam screws (100481) into the holes on the underside of the plinth board, until the collar touches the board.
- Frame onto the board — Turn the frame upside down and lower it onto the board, so the dowels and cam screws go into its holes. Check: The curved front apron goes along the board's front edge.
- Back apron in — Turn the back apron over and lower it between the side pieces at the back, onto the board's dowel holes and cam screws.
- Foot pads — Press a foot pad onto the end of each leg: pads A (10006536) at the front left and back right, pads B (10006543) at the front right and back left. Their pins go into the holes. Check: Check the letter on each pad: A and B are mirror images.
- Screw the brackets — Fix each angle bracket to the side piece next to it with a screw (100347).
- Lock the plinth and turn it over — Press 12 cam locks (103430) into the aprons and side pieces under the board and turn each one clockwise to lock. Then turn the plinth over onto its feet.
- Cam screws on the plinth — Open bag 2. Screw 4 cam screws (118331) into the holes near the sides of the plinth board's top.
- Cam screws in the sides — Lay the two side panels and the middle shelf flat on a soft surface, side panels inner face up. Screw 2 cam screws (118331) into the holes in the lower part of each side panel.
- Dowels in the middle shelf — Tap 2 dowels (101345) into the holes in each end of the middle shelf (the board with the rounded front edge).
- Shelf into the right side — Stand the right side panel up on its back edge. Stand the middle shelf up on its back edge too, rounded edge up, and push it into the right side panel so the dowels and cam screws go into the holes.
- Left side on — Stand the left side panel up on its back edge and push it onto the dowels and cam screws at the other end of the shelf.
- Lock the shelf — Press 4 cam locks (103430) into the underside of the middle shelf, 2 at each end, and turn each one clockwise to lock.
- Dowels in the side edges, stand it up — Tap 8 dowels (101345) into the side panels: 2 into the top edge and 2 into the bottom edge of each one. Then stand the cabinet up.
- Onto the plinth — Lift the cabinet onto the plinth, front to front, so the dowels and the cam screws go into the holes in the side panels. Check: The rounded edge of the middle shelf and the curved plinth apron both face the front.
- Lock to the plinth — Press 4 cam locks (103430) into the side panels just above the plinth and turn each one clockwise.
- Cam screws for the divider — Screw 2 cam screws (118331) into the holes in the middle of the shelf's top.
- Divider — Tap 2 dowels (101345) into each end of the divider. Lower it onto the middle of the shelf, so the dowels and cam screws go into the holes.
- Lock the divider — Press 2 cam locks (103430) into the left face of the divider, just above the shelf, and turn them clockwise.
- Back panel — Slide the back panel down into the grooves at the back of the side panels, cut corners at the top, until it reaches the plinth.
- Cam screws in the top — Lay the top upside down in front of the cabinet, the rounded edge at the front. Screw 6 cam screws (118331) into its holes: 2 near each side and 2 in the middle.
- Top on — Turn the top over and lower it onto the cabinet, so the dowels and cam screws go into the holes in the side panels and the divider.
- Lock the top — Press 6 cam locks (103430) in just under the top: 2 into each side panel and 2 into the divider. Turn each one clockwise.
- Fix the back to the shelf — From the back, push 4 plugs (151708) through the holes in the back panel into the middle shelf, then press a pin (151707) into each plug.
- Back clips — Push 8 clips (10093081) into the holes in the side panels just behind the back panel, 4 on each side. Slide a cap (10093082) onto each clip so it holds the edge of the back panel.
- Wall brackets — Press the 2 wall brackets (141413) onto the inner faces of the side panels, in the cut corners at the top of the back panel, with the threaded drum towards the wall.
- Drawer runners — Fix a drawer runner to the inside of each side panel, at the bottom of the drawer opening, with 2 screws (100347).
- Spacers (with a skirting board) — If there is a skirting board, screw a spacer (141414) into each wall bracket from behind. Later turn them out until they touch the wall, so the cabinet stands straight. Without a skirting board, leave them out.
- Against the wall — Push the cabinet back against the wall. Check: Fix the cabinet to the wall to stop it tipping over.
- Fix it to the wall — From inside the cabinet, put a washer (126916) on a wall screw and drive it through each bracket into the wall. Click a cover cap (133303) onto each washer. Check: Wall screws and plugs are not included: use fixings that suit your wall. Ask a specialist if unsure.
- Shelf supports — Push 16 shelf supports (131372) into the holes at the height you want: 4 per shelf, 2 shelves on each side of the divider.
- Shelves — Slide the 4 shelves in from the front, just above the supports, and lower them onto them.
- Bumpers on the doors — Open bag 3. Lay both doors face down on a soft surface. Press 2 bumpers (107586) into the holes along the free edge of each door, one at each end.
- Hinges 10031762 — Press a hinge (10031762) into the round hole at the top of each door and tighten its 2 screws.
- Hinges 10031756 — Press a hinge (10031756) into the round hole at the bottom of each door and tighten its 2 screws.
- Hang the doors — Hold each door against the cabinet and click its hinges onto the mounting plates inside the side panel: press the IKEA logo on each hinge. Check: The doors hinge on the outer sides and meet at the divider.
- Tighten the mounting plates — Tighten the screw on each of the 4 hinge mounting plates so the doors are held firmly.
- Handles — Hold a handle (10006275) against the front of each door, at the hole near its free edge, and screw it on from the inside with a screw (151743). Then close the doors. Check: Use the short screws 151743 here; the long ones (119976) are for the drawer knobs.
- Cam screws in the drawer front — Lay the drawer front face down on a soft surface. Screw 4 cam screws (118331) into the holes near its ends, 2 at each end.
- Drawer sides — Tap a dowel (101345) into the front next to each pair of cam screws and one into the far end of each drawer side. Stand the sides on the front, so the dowel and cam screws go into the holes.
- Lock the drawer sides — Press 4 cam locks (112399) into the inner faces of the sides near the front, and turn each one clockwise.
- Drawer bottom — Slide the drawer bottom into the grooves in the sides and the front, from the open end, until it stops.
- Cam screws in the drawer back — Lay the drawer back flat next to the drawer, the groove facing the drawer bottom. Screw 4 cam screws (118331) into the holes near its ends.
- Drawer back on — Turn the back over and lay it on the ends of the sides, over the drawer bottom, so the dowels and cam screws go into the holes.
- Lock the drawer back — Press 4 cam locks (112399) into the inner faces of the sides near the back, and turn each one clockwise.
- Bumpers, turn the drawer over — Press a bumper (107586) into the hole at each end of the drawer front, outside the sides. Then turn the drawer upside down.
- Support bar — Lay the support bar (128765) across the middle of the drawer bottom, from the front to the back, with its bent ends over the front and the back.
- Screw the bar — Fix the support bar with 3 screws (105344): 2 through its tab into the front and 1 through its tab into the back.
- Knobs — Turn the drawer the right way up. Hold a knob (10006309) against the front of the drawer and screw it on from the inside with a long screw (119976). Fit both knobs.
- Drawer in — Set the drawer on the runners and push it in, so the hooks at the back of the runners catch the drawer.
- Lock clips — Pull the drawer half out. Screw a lock clip (124218) into the hole under each side at the front and turn its lever onto the runner. Push the drawer closed.
- Done! — Your LOMMARP cabinet is built and fixed to the wall. If the doors or the drawer front do not line up, adjust them with the hinge screws and the lock clips (manual pages 35-36).
LOMMARP cabinet: questions and answers
How long does it take to assemble the IKEA LOMMARP cabinet?
About 3–4 hours for 2 people, working through the 58 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the LOMMARP cabinet?
Flat-blade screwdriver, Phillips screwdriver, wall screws and plugs (not included).
Can one person assemble the LOMMARP cabinet?
It is planned as a 2-person build. One person can do most of it, but get help for steps 4, 10 and 13, where the furniture is lifted or turned.
Does the LOMMARP cabinet need to be fixed to the wall?
The manual shows a wall fixing: see step 32 (Wall brackets) and step 36 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the LOMMARP cabinet once assembled?
102×50×101 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the LOMMARP cabinet?
208 fittings of 29 kinds, the most numerous being 34 × dowel, 32 × cam lock, 24 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA LOMMARP cabinet assembly instructions PDF?
The official PDF is manual AA-2194723-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 804.154.68 (dark blue green); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2194723-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example support bar 128765). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA LOMMARP cabinet with glass doors assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
- IKEA EKET cabinet assembly instructions
All IKEA LOMMARP assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained