Step by StepAssembly Find your furniture

IKEA LOMMARP cabinet with glass doors assembly instructions

How to assemble the IKEA LOMMARP cabinet with glass doors, step by step: 64 animated steps built from the official manual, about 4–5 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, wall screws and plugs (not included).

IKEA LOMMARP cabinet with glass doors, assembled

A tall dark blue-green cabinet in two parts: a panelled lower cabinet on a shaped plinth and a glass-sided display cabinet with a cornice on top, closed by two glass doors and two panelled doors. Size: 86×49×199 cm. About 4–5 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Wall screws and plugs (not included).

Based on the official IKEA manual AA-2159837-3 (PDF). Guide updated .

LOMMARP cabinet with glass doors: quick facts
Steps64
Time4–5 hours
People2
ToolsFlat-blade screwdriver, Phillips screwdriver, Wall screws and plugs (not included)
Size86×49×199 cm
Official manualAA-2159837-3
IKEA article number403.837.37 (dark blue green)
Pieces in the box292

In the box

PartPart numberQuantity
Front apron1
Back apron1
Plinth side piece2
Plinth board1
Side panel2
Back rail (small holes)2
Back panel1
Middle top1
Glass side panel2
Back rail (big holes)2
Back panel (planked)1
Gallery front1
Gallery side rail2
Top board1
Shelf4
Glass door2
Panelled door2
Cam screw10048114
Dowel10134550
Screw1003478
Angle bracket1037174
Cam lock12233240
Foot pad A100065362
Foot pad B100065432
Cam screw11833126
Socket1007555816
Pin1005108416
Clip1009308116
Cap1009308216
Screw1090605
Washer1148695
Screw1090492
Washer1008234
Wall bracket1069892
Shelf support13137216
Handle100062752
Knob100063092
Screw1199762
Screw1517432
Bumper1070914
Hinge100317524
Hinge1468844

Steps

  1. Cam screws in the side pieces — Open bag 1. Lay the front apron and the two shaped side pieces flat on a soft surface, in a row. Screw 2 cam screws (100481) into the inner face of each side piece, near the end that meets the apron. Stop when the collar touches the wood. Check: Do not over-tighten: the collar must sit on the surface, not sink into it.
  2. Dowels in the front apron — Tap 2 wooden dowels (101345) into the holes in each end of the front apron.
  3. Swing the side pieces up — Swing both side pieces up so they stand on edge at the ends of the apron, then push them onto the dowels and cam screws.
  4. Lock the plinth frame — Press 4 cam locks (122332) into the apron, arrows towards the cam screws, and turn each one clockwise to lock. Then turn the frame over onto its legs.
  5. Dowels on top of the frame — Tap 6 dowels (101345) into the holes along the top edge of the frame: 2 in the front apron and 2 in each side piece.
  6. Brackets on the back apron — Lay the plinth board upside down, the rounded edge at the front. Lay the back apron flat, inner face up, and screw 4 angle brackets (103717) onto it near its ends with a screw (100347) each. Check: The board's rounded edge goes at the front and both sides.
  7. Dowels in the back apron — Tap 2 dowels (101345) into the holes in the long straight edge of the back apron.
  8. Cam screws in the plinth board — Screw 10 cam screws (100481) into the holes on the underside of the plinth board, until the collar touches the board.
  9. Frame onto the board — Turn the frame upside down and lower it onto the board, so the dowels and cam screws go into its holes. Check: The curved front apron goes along the board's front edge.
  10. Back apron in — Turn the back apron over and lower it between the side pieces at the back, onto the board's dowel holes and cam screws.
  11. Foot pads — Press a foot pad onto the end of each leg: pads A (10006536) at the front left and back right, pads B (10006543) at the front right and back left. Their pins go into the holes. Check: Check the letter on each pad: A and B are mirror images.
  12. Screw the brackets — Fix each angle bracket to the side piece next to it with a screw (100347).
  13. Lock the plinth and turn it over — Press 10 cam locks (122332) into the aprons and side pieces under the board and turn each one clockwise to lock. Then turn the plinth over onto its feet.
  14. Cam screws on the plinth — Open bag 2. Screw 4 cam screws (118331) into the holes near the sides of the plinth board's top.
  15. Cam screws in the lower sides — Lay both side panels of the lower cabinet flat, inner face up. Screw 2 cam screws (118331) into the holes at the back edge of each one.
  16. Back rails on the left side — Use the 2 narrow rails with small holes (not the ones with big holes). Tap a dowel (101345) into each end, then stand the rails on the left side panel, one at each end of its back edge. Check: The rails with the big holes are for the glass cabinet.
  17. Lock the rails and stand it up — Press 2 cam locks (122332) into the rails next to the side panel and turn them clockwise. Turn the side panel up so it stands on its bottom edge with the rails across.
  18. Right side on — Stand the right side panel up and push it onto the dowels and cam screws at the other ends of the rails.
  19. Lock and lay it on its back — Press 2 cam locks (122332) into the rails at the right side and turn them clockwise. Then lay the cabinet down on its back.
  20. Dowels in the edges — Tap 10 dowels (101345) in: 2 into the top edge and 2 into the bottom edge of each side panel, and 2 into the bottom edge of the bottom rail.
  21. Onto the plinth — Stand the cabinet up and lower it onto the plinth, so the dowels and cam screws go into the holes in the side panels. Check: Lift with two people.
  22. Lock to the plinth — Press 4 cam locks (122332) into the side panels just above the plinth and turn each one clockwise.
  23. Back panel — Slide the back panel down into the grooves at the back of the side panels, plain side facing out, until it sits in the groove at the bottom. Check: The plain side faces the room; the grooved side is for the glass cabinet.
  24. Cam screws in the middle top — Lay the middle top upside down in front of the cabinet, the rounded edge at the front. Screw 4 cam screws (118331) into the holes near its sides.
  25. Middle top on — Turn the middle top over and lower it onto the cabinet, so the dowels and cam screws go into the side panels.
  26. Lock the middle top — Press 4 cam locks (122332) into the side panels just under the middle top and turn each one clockwise.
  27. Fix the back to the rails — From the back, push a socket (10075558) into each of the 8 holes along the top and bottom of the back panel, then press a pin (10051084) into each socket.
  28. Back clips — Push 8 clips (10093081) into the holes in the side panels just behind the back panel, 4 on each side. Slide a cap (10093082) onto each clip so it holds the edge of the back panel.
  29. Cam screws for the glass cabinet — Open bag 3. Screw 4 cam screws (118331) into the holes near the sides of the middle top.
  30. Cam screws in the glass sides — Lay both glass side panels flat on a soft surface, inner face up. Screw 2 cam screws (118331) into the holes at the back edge of each one. Check: Handle the glass panels with care and lay them on a soft surface.
  31. Back rails on the right glass side — Tap a dowel (101345) into each end of the 2 rails with big holes, then stand the rails on the right glass side, one at each end of its back edge.
  32. Lock the rails and stand it up — Press 2 cam locks (122332) into the rails next to the glass side and turn them clockwise. Turn the glass side up so it stands on its bottom edge.
  33. Left glass side on — Stand the left glass side up and push it onto the dowels and cam screws at the other ends of the rails.
  34. Lock the left side — Press 2 cam locks (122332) into the rails at the left side and turn them clockwise.
  35. Dowels in the gallery sides — For the cornice, take the two short gallery rails and tap a dowel (101345) into the hole in the front end of each one.
  36. Cam screws in the gallery front — Lay the long gallery front on its face and screw 2 cam screws (118331) into the holes near its ends. Then turn it upright and push it onto the side rails.
  37. Lock the gallery — Press 2 cam locks (122332) into the holes on top of the side rails and turn them clockwise. Then turn the gallery over.
  38. Dowels under the gallery — Tap 6 dowels (101345) into the holes along the gallery's underside: 2 in the front and 2 in each side rail.
  39. Gallery onto the top board — Lay the top board flat, rounded edge at the front. Turn the gallery back over and lower it onto the board so the dowels go into the holes along the front and sides.
  40. Screw the gallery to the board — Put a washer (114869) on each of 5 screws (109060) and screw them through the gallery into the top board. Then turn the cornice over.
  41. Cam screws under the cornice — Screw 4 cam screws (118331) into the holes near the sides of the top board's underside.
  42. Dowels on top of the glass cabinet — Tap 6 dowels (101345) into the top edges: 2 into each glass side and 2 into the top rail.
  43. Cornice on — Turn the cornice the right way up and lower it onto the glass cabinet, so the dowels and cam screws go into the holes.
  44. Lock the cornice — Press 4 cam locks (122332) into the glass sides just under the cornice and turn each one clockwise. Then lay the cabinet down on its front.
  45. Lay it on its front — With a helper, lay the glass cabinet down on its front on a soft surface. Check: Two people: the cabinet is tall and has glass sides.
  46. Planked back panel — Slide the planked back panel into the grooves from the open bottom end, planks facing into the cabinet, until it reaches the top. Check: The planked side faces in, so you see it through the glass.
  47. Fix the back to the rails — Push a socket (10075558) into each of the 8 holes along the top and bottom of the back panel, then press a pin (10051084) into each socket.
  48. Back clips — Push 8 clips (10093081) into the holes in the glass sides next to the back panel, 4 on each side, and slide a cap (10093082) onto each clip over the panel's edge.
  49. Dowels in the bottom edges — Tap 6 dowels (101345) into the bottom edges: 2 into each glass side and 2 into the bottom rail.
  50. Onto the lower cabinet — Stand the glass cabinet up. With a helper, lift it onto the lower cabinet so the dowels and cam screws go into the holes in the middle top. Check: This needs two people.
  51. Lock the glass cabinet — Press 4 cam locks (122332) into the glass sides just above the middle top and turn each one clockwise.
  52. Wall brackets on the top — Place the cabinet near the wall. Screw the 2 wall brackets (106989) onto the top at the back with a screw (109049) and a washer (100823) each, the upright leg flush with the back.
  53. Against the wall — Push the cabinet back against the wall. Check: Fix the cabinet to the wall to stop it tipping over.
  54. Fix it to the wall — Drive a wall screw through a washer (100823) and the slot of each bracket into the wall. Check: Wall screws and plugs are not included: use fixings that suit your wall. Ask a specialist if unsure.
  55. Shelf supports — Push 16 shelf supports (131372) into the holes at the height you want: 4 per shelf, 2 shelves in the glass cabinet and 2 in the lower cabinet.
  56. Shelves — Slide the 4 shelves in from the front, just above the supports, and lower them onto them.
  57. Hinges 10031752 — Lay the 4 doors face down on a soft surface. Press a hinge (10031752) into the round hole at the top of each door and fix it with its 2 screws.
  58. Hinges 146884 — Lay the 4 doors face down on a soft surface. Press a hinge (146884) into the round hole at the bottom of each door and fix it with its 2 screws.
  59. Hang the doors — Hold each door against the cabinet and click its hinges onto the mounting plates inside the side panel. Check: Glass doors at the top, panelled doors at the bottom; hinges on the outer sides.
  60. Tighten the mounting plates — Tighten the screw on each of the 8 hinge mounting plates so the doors are held firmly.
  61. Handles on the glass doors — Open bag 4. Hold a handle (10006275) against the front of each glass door, at the hole near its free edge, and screw it on from the inside with a screw (151743).
  62. Knobs on the lower doors — Hold a knob (10006309) against the front of each lower door and screw it on from the inside with a screw (119976).
  63. Door bumpers — Stick a bumper (107091) on the inside of each door, near the hinge edge, where it meets the side panel. Then close the doors.
  64. Done! — Your LOMMARP cabinet is built and fixed to the wall. If the doors do not line up, adjust them with the screws on the hinges (manual page 35).

LOMMARP cabinet with glass doors: questions and answers

How long does it take to assemble the IKEA LOMMARP cabinet with glass doors?

About 4–5 hours for 2 people, working through the 64 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the LOMMARP cabinet with glass doors?

Flat-blade screwdriver, Phillips screwdriver, wall screws and plugs (not included).

Can one person assemble the LOMMARP cabinet with glass doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 4, 10 and 13, where the furniture is lifted or turned.

Does the LOMMARP cabinet with glass doors need to be fixed to the wall?

The manual shows a wall fixing: see step 52 (Wall brackets on the top) and step 54 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the LOMMARP cabinet with glass doors once assembled?

86×49×199 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the LOMMARP cabinet with glass doors?

264 fittings of 25 kinds, the most numerous being 50 × dowel, 40 × cam lock, 26 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA LOMMARP cabinet with glass doors assembly instructions PDF?

The official PDF is manual AA-2159837-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 403.837.37 (dark blue green); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2159837-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 100481). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA LOMMARP assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained