Step by StepAssembly Find your furniture

IKEA NYSJÖN tall cabinet assembly instructions

How to assemble the IKEA NYSJÖN tall cabinet, step by step: 30 animated steps built from the official manual, about 1.5–2 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, pencil, spirit level, drill with 5 mm bit, clamp and a scrap of wood, wall screws and plugs (not included).

IKEA NYSJÖN tall cabinet, assembled

A tall, narrow white bathroom cabinet: a cam-lock frame built lying on its side, a nailed-on back, two front legs, fixing to the wall, four shelves and one hinged door with a knob. Size: 30x190 cm. About 1.5–2 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Spirit level, Drill with 5 mm bit, Clamp and a scrap of wood, Wall screws and plugs (not included).

Based on the official IKEA manual AA-2246305-7 (PDF). Guide updated .

NYSJÖN tall cabinet: quick facts
Steps30
Time1.5–2 hours
People2
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Spirit level, Drill with 5 mm bit, Clamp and a scrap of wood, Wall screws and plugs (not included)
Size30x190 cm
Official manualAA-2246305-7
IKEA article number204.708.15 (high white)
Pieces in the box88

In the box

PartPart numberQuantity
Side panel2
Top / bottom2
Back panel1
Shelf4
Door1
Wall bracket100322744
Screw100488818
Cam screw1234928
Dowel1013758
Cam lock1025098
Nail guide1054941
Nails 101221 (bag of 30)1
Leg100597812
Leg plate100687472
Screw1244314
Adjustable foot100567342
Wall plate1536474
Bracket cover100435694
Shelf pin1004382616
Hinge1445533
Knob1062661
Bolt1199761
Bumpers 107091 (sheet of 2)1

Steps

  1. Wall brackets on the side panels — Lay both side panels flat on a soft surface, inner faces up. Fix a wall bracket 10032274 at each end of each panel, on its back edge, with 2 screws 10048881 each: 4 brackets and 8 screws in all.
  2. Cam screws — Screw a cam screw 123492 into each of the 8 small holes near the ends of the side panels (2 at each end), until the collar sits on the panel.
  3. Dowels in the top and bottom — Lay the top and the bottom flat, the faces with the large round holes up. Push 4 dowels 101375 into the small holes in the edges of each panel, 2 in each edge.
  4. Top and bottom onto a side panel — The left side panel stays flat, front edge towards you. Stand the bottom and the top on it, one at each end, large holes facing out, and push them down so their dowels and the cam screws go into the holes.
  5. Lock the bottom at the lower panel — Push 2 cam locks 102509 into the large holes of the bottom that face the lying side panel, arrow towards the edge, and turn each clockwise with a flat-blade screwdriver to pull the panels tight.
  6. Lock the top at the lower panel — Do the same at the top: 2 cam locks 102509 in the large holes next to the lying side panel, each turned clockwise until tight.
  7. Put the other side panel on — Turn the second side panel over, inner face down, brackets at the back like the first one. Lower it onto the top and bottom so their dowels and its cam screws go into the holes.
  8. Lock the bottom at the upper panel — Push 2 more cam locks 102509 into the bottom, next to the side panel you just put on, and turn them clockwise.
  9. Lock the top at the upper panel — Push the last 2 cam locks 102509 into the top and turn them clockwise.
  10. Turn it onto its front, back panel on — Tip the frame forward so it lies on its front edges. Lay the back panel on the back, the 4 holes over the wall brackets.
  11. First nail: bottom corner — Push the back panel into the corner at the bottom of the left side panel. Put a nail 101221 in the nail guide 105494, hold the guide on the back panel, hammer the nail down to the guide, pull the guide away and hammer the nail home.
  12. Second nail: top corner — Line the back panel up with the top end of the same side panel and nail it there in the same way, with the nail guide.
  13. Third nail: the bottom edge — Push the back panel flush with the bottom and nail it in the middle of the bottom edge. The frame is now square.
  14. Nail the back all round — Hammer in the other 27 nails 101221 with the nail guide, all round the edges: along both side panels and across the top and the bottom.
  15. Back on its side, legs on — Tip the cabinet back onto its side. At each front corner of the bottom, put a plate 10068747 and a leg 10059781 on it, then fix the leg with 2 screws 124431: one through the plate, one into the bottom.
  16. Adjustable feet — Screw an adjustable foot 10056734 into the end of each leg by hand.
  17. Stand it up against the wall — With a helper, stand the cabinet up and push it against the wall where it will hang. Check the top with a spirit level and turn the feet in or out until the cabinet stands level. Check: Get help to stand the cabinet up: it is 190 cm tall.
  18. Mark the wall — Mark the wall with a pencil through the square hole in each of the 4 wall brackets.
  19. Screws in the wall — Move the cabinet away. Drill and plug the wall at the 4 marks if your wall needs it, and drive in 4 screws with a round (pan) head. Leave each head standing out about 1 cm. Check: Screws and plugs for the wall are not included: choose ones that suit your wall. Use pan-head screws, not countersunk ones.
  20. Push it back onto the screws — Bring the cabinet back in front of the screws and push it straight back against the wall, so the 4 screw heads come through the holes in the back panel and the square holes of the brackets.
  21. Wall plates, tighten the screws — Slide a wall plate 153647 over each screw head inside the brackets. Check that the cabinet stands straight, then tighten the 4 screws so the plates clamp the brackets to the wall.
  22. Bracket covers — Click a cover 10043569 over each of the 4 wall brackets.
  23. Shelf pins — Push 16 shelf pins 10043826 into the holes in the side panels: 4 at the same height for each of the 4 shelves.
  24. Shelves — Slide the 4 shelves in and lay each one on its 4 shelf pins.
  25. Hinges on the door — Lay the door face down. Press the 3 hinges 144553 into the round holes along one long edge, arms pointing out, and tighten the 2 screws of each hinge. The door can hang on the left or right: these steps hang it on the left.
  26. Hang the door — Hold the door open next to the left side panel and put the hinge plates against the inside of the panel, at the front holes. Screw each plate on with its 2 screws. Check: Once the door hangs, it can be adjusted up and down, sideways and in and out with the hinge screws.
  27. Drill the knob hole — On the inside of the door, mark a point 30 mm from the free edge at the height of the middle hinge. Clamp a scrap of wood to the front behind the mark and drill straight through with a 5 mm bit. Check: Without the scrap of wood behind it, the drill splinters the front of the door.
  28. Knob — Hold the knob 106266 on the front of the door over the hole and screw the bolt 119976 into it from the inside.
  29. Bumpers, close the door — Stick the 2 bumpers 107091 on the inside of the door, at the top and bottom corners of the free edge. Then close the door.
  30. Done! — Your NYSJÖN tall cabinet is finished and fixed to the wall. The shelves can be moved to other heights with the shelf pins.

NYSJÖN tall cabinet: questions and answers

How long does it take to assemble the IKEA NYSJÖN tall cabinet?

About 1.5–2 hours for 2 people, working through the 30 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the NYSJÖN tall cabinet?

Phillips screwdriver, flat-blade screwdriver, hammer, pencil, spirit level, drill with 5 mm bit, clamp and a scrap of wood, wall screws and plugs (not included).

Can one person assemble the NYSJÖN tall cabinet?

It is planned as a 2-person build. One person can do most of it, but get help for steps 7 and 17, where the furniture is lifted or turned.

Does the NYSJÖN tall cabinet need to be fixed to the wall?

The manual shows a wall fixing: see step 1 (Wall brackets on the side panels) and step 18 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the NYSJÖN tall cabinet once assembled?

30x190 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the NYSJÖN tall cabinet?

76 fittings of 16 kinds, the most numerous being 16 × shelf pin, 8 × screw, 8 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA NYSJÖN tall cabinet assembly instructions PDF?

The official PDF is manual AA-2246305-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 204.708.15 (high white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2246305-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example wall bracket 10032274). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA NYSJÖN assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained