IKEA NYSJÖN laundry cabinet assembly instructions
How to assemble the IKEA NYSJÖN laundry cabinet, step by step: 34 animated steps built from the official manual, about 1.5–2 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, awl, hammer, pencil, spirit level, drill with 5 mm bit, clamp and a scrap of wood, wall screws (not included).
A tall white laundry cabinet: a cam-lock frame with two fixed shelves built lying on its side, a nailed-on back, two front legs, fixing to the wall, a door with two laundry holes, and two laundry bags inside. Size: 40x190 cm. About 1.5–2 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Awl, Hammer, Pencil, Spirit level, Drill with 5 mm bit, Clamp and a scrap of wood, Wall screws (not included).
Based on the official IKEA manual AA-2250653-9 (PDF). Guide updated .
| Steps | 34 |
|---|---|
| Time | 1.5–2 hours |
| People | 2 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Awl, Hammer, Pencil, Spirit level, Drill with 5 mm bit, Clamp and a scrap of wood, Wall screws (not included) |
| Size | 40x190 cm |
| Official manual | AA-2250653-9 |
| IKEA article number | 404.964.71 (white) |
| Pieces in the box | 105 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top / bottom | 2 | |
| Fixed shelf | 2 | |
| Back panel | 1 | |
| Door | 1 | |
| Laundry bag with board | 2 | |
| Wall bracket | 10032274 | 4 |
| Screw | 10048881 | 8 |
| Cam screw | 123492 | 16 |
| Dowel | 101375 | 16 |
| Cam lock | 102509 | 16 |
| Nail guide | 105494 | 1 |
| Nails 101221 (bag of 30) | 1 | |
| Leg | 10059781 | 2 |
| Leg plate | 10068747 | 2 |
| Screw | 124431 | 6 |
| Adjustable foot | 10056734 | 2 |
| Wall plate | 153647 | 4 |
| Bracket cover | 10043569 | 4 |
| Hinge | 144553 | 3 |
| Grommet | 123056 | 2 |
| Cap | 139244 | 3 |
| Knob | 106266 | 1 |
| Bolt | 119976 | 1 |
| Bumpers 107091 (sheet of 2) | 1 | |
| Door stop | 123029 | 2 |
Steps
- Wall brackets on the side panels — Lay both side panels flat on a soft surface, inner faces up. Fix a wall bracket 10032274 at each end of each panel, on its back edge, with 2 screws 10048881 each: 4 brackets and 8 screws in all.
- Cam screws — Screw a cam screw 123492 into each of the 16 small holes in the inner faces of the side panels, 8 in each panel (2 for the top, each fixed shelf and the bottom), until the collar sits on the panel.
- Dowels in the top, shelves and bottom — Lay the top, the 2 fixed shelves and the bottom flat, the faces with the large round holes up. Push 4 dowels 101375 into the small holes in the end edges of each panel, 2 in each end: 16 in all.
- Panels onto a side panel — The left side panel stays flat, front edge towards you. Stand the top, the 2 fixed shelves and the bottom on it, large holes as in the manual, and push each down so its dowels and the cam screws go into the holes. Check: The large holes must face the cam screws: they are on the face of the panel, not on its edge.
- Lock the top at the lower panel — Push 2 cam locks 102509 into the large holes in the top's upper face, next to the lower side panel, arrow towards the edge. Turn each clockwise with a flat-blade screwdriver to pull the panels tight.
- Lock the shelves and bottom at the lower panel — Do the same on the undersides of the 2 fixed shelves and of the bottom: 2 cam locks 102509 in each, next to the lower side panel, each turned clockwise until tight (6 in all).
- Put the other side panel on — Turn the second side panel over, inner face down, brackets at the back like the first one. Lower it onto the 4 panels so their dowels and its cam screws go into the holes.
- Lock the top at the upper panel — Push 2 cam locks 102509 into the large holes in the top's upper face, next to the upper side panel, arrow towards the edge. Turn each clockwise with a flat-blade screwdriver to pull the panels tight.
- Lock the shelves and bottom at the upper panel — Do the same on the undersides of the 2 fixed shelves and of the bottom: 2 cam locks 102509 in each, next to the upper side panel, each turned clockwise until tight (6 in all).
- Turn it onto its front, back panel on — Tip the frame forward so it lies on its front edges. Lay the back panel on the back, the 4 holes over the wall brackets.
- First nail: bottom corner, far side — Push the back panel into the corner at the bottom end of the far side panel. Put a nail 101221 in the nail guide 105494, hold the guide on the back panel, hammer the nail down to the guide, pull the guide away and hammer the nail home.
- Second nail: top corner, far side — Line the back panel up with the top end of the same side panel and nail it there in the same way, with the nail guide.
- Third nail: bottom corner, near side — Push the back panel flush with the near side panel at the bottom end and nail it there. The frame is now square.
- Nail the back all round — Hammer in the other 27 nails 101221 with the nail guide, all round the edges: along both side panels and across the top and the bottom.
- Back on its side, legs on — Tip the cabinet back onto its side. At each front corner of the bottom, put a plate 10068747 and a leg 10059781 on it, then fix the leg with 2 screws 124431: one through the plate, one into the bottom.
- Adjustable feet — Screw an adjustable foot 10056734 into the end of each leg by hand.
- Stand it up against the wall — With a helper, stand the cabinet up and push it against the wall where it will hang. Check the top with a spirit level and turn the feet in or out until the cabinet stands level. Check: Get help to stand the cabinet up: it is 190 cm tall.
- Mark the wall — Mark the wall with a pencil through the square hole in each of the 4 wall brackets.
- Screws in the wall — Move the cabinet away. At each of the 4 marks, put in a screw with a round (pan) head that suits your wall. Leave each head standing out about 1 cm. Check: Wall screws (and plugs, if your wall needs them) are not included. Use pan-head screws, not countersunk ones.
- Push it back onto the screws — Bring the cabinet back in front of the screws and push it straight back against the wall, so the 4 screw heads come through the holes in the back panel and the square holes of the brackets.
- Wall plates, tighten the screws — Slide a wall plate 153647 over each screw head inside the brackets. Check that the cabinet stands straight, then tighten the 4 screws with a flat-blade screwdriver so the plates clamp the brackets to the wall.
- Bracket covers — Click a cover 10043569 over each of the 4 wall brackets.
- Hinges on the door — Lay the door face down, the hole nearer one end at the top. Press the 3 hinges 144553 into the round holes along one long edge, arms pointing out, and tighten the 2 screws of each hinge. The door can hang on the left or right: these steps hang it on the left.
- Hang the door — Hold the door open next to the left side panel and put the hinge plates against the inside of the panel, at the front holes. Screw each plate on with its 2 screws. Check: Once the door hangs, it can be adjusted up and down, sideways and in and out with the hinge screws (manual page 27).
- Grommets: front rings — Each grommet 123056 has two rings. Hold the plain ring against the front of the door in each laundry hole, its sleeve in the hole.
- Grommets: click the inner rings in — From the inside of the door, push the toothed ring into each hole until it clicks into the front ring.
- Caps on the free edge — The free edge of the door has hinge holes too, for hanging it the other way. Press a cap 139244 over each of these 3 holes, its pegs in the small holes.
- Drill the knob hole — On the inside of the door, mark a point 30 mm from the free edge, level with the lower edge of the middle hinge, just under the cap. Clamp a scrap of wood to the front behind the mark and drill straight through with a 5 mm bit. Check: Without the scrap of wood behind it, the drill splinters the front of the door.
- Knob — Hold the knob 106266 on the front of the door over the hole and screw the bolt 119976 into it from the inside.
- Bumpers — Stick the 2 bumpers 107091 on the inside of the door, at the top and bottom corners of the free edge.
- Door stops — On the inside of the left side panel, just behind the middle and the bottom hinge, start a hole with an awl. Screw a door stop 123029 on at each hole with a screw 124431 through its middle. The stops keep the laundry bags away from the hinges.
- Open the laundry bags — Pull each laundry bag open by its top edge. Push the stiffening board down into the bag and lay it flat on the bottom.
- Bags into the cabinet — Put one laundry bag in the middle compartment and the other in the bottom compartment, handles to the front, so laundry dropped through the door holes falls into them. Close the door.
- Done! — Your NYSJÖN laundry cabinet is finished and fixed to the wall. Drop laundry through the two holes in the door; open the door to lift the bags out by their handles.
NYSJÖN laundry cabinet: questions and answers
How long does it take to assemble the IKEA NYSJÖN laundry cabinet?
About 1.5–2 hours for 2 people, working through the 34 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the NYSJÖN laundry cabinet?
Phillips screwdriver, flat-blade screwdriver, awl, hammer, pencil, spirit level, drill with 5 mm bit, clamp and a scrap of wood, wall screws (not included).
Can one person assemble the NYSJÖN laundry cabinet?
It is planned as a 2-person build. One person can do most of it, but get help for steps 7, 17 and 34, where the furniture is lifted or turned.
Does the NYSJÖN laundry cabinet need to be fixed to the wall?
The manual shows a wall fixing: see step 1 (Wall brackets on the side panels) and step 18 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the NYSJÖN laundry cabinet once assembled?
40x190 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the NYSJÖN laundry cabinet?
93 fittings of 18 kinds, the most numerous being 16 × cam screw, 16 × dowel, 16 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA NYSJÖN laundry cabinet assembly instructions PDF?
The official PDF is manual AA-2250653-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 404.964.71 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2250653-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example wall bracket 10032274). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA NYSJÖN tall cabinet assembly instructions
- IKEA NYSJÖN cabinet for washing machine assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
All IKEA NYSJÖN assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained