IKEA VIHALS sideboard assembly instructions
How to assemble the IKEA VIHALS sideboard, step by step: 40 animated steps built from the official manual, about 2.5–3.5 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (for the wall plugs).
A white VIHALS sideboard: a keyhole-joined frame built lying on its front, two slide-in back panels, wall fixing, four hinged doors, two shelves and two cam-lock drawers on roller runners. Size: 140x37x75 cm. About 2.5–3.5 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (for the wall plugs).
Based on the official IKEA manual AA-2283730-6 (PDF). Guide updated .
| Steps | 40 |
|---|---|
| Time | 2.5–3.5 hours |
| People | 2 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (for the wall plugs) |
| Size | 140x37x75 cm |
| Official manual | AA-2283730-6 |
| IKEA article number | 304.917.18 (white) |
| Pieces in the box | 160 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Middle panel | 1 | |
| Top | 1 | |
| Bottom | 1 | |
| Back panel | 2 | |
| Shelf | 2 | |
| Door | 4 | |
| Drawer front | 2 | |
| Drawer side | 4 | |
| Drawer back | 2 | |
| Drawer bottom | 2 | |
| Drawer runner set 10060247 (CL, CR, DL, DR) | 2 | |
| Screw | 10048881 | 12 |
| Glide | 10061178 | 6 |
| Wooden dowel | 101345 | 8 |
| Expanding plug | 10050769 | 4 |
| Pin | 10050771 | 4 |
| Locking screw | 10077982 | 4 |
| Allen key | 100092 | 1 |
| Bracket | 10003780 | 2 |
| Screw | 105811 | 4 |
| Wall bracket | 106989 | 2 |
| Screw | 109049 | 2 |
| Washer | 100823 | 4 |
| Wall screw | 109048 | 2 |
| Wall plug | 121714 | 2 |
| Shelf support | 10051660 | 8 |
| Hinge | 10071303 | 8 |
| Handle | 10071494 | 6 |
| Screw | 146114 | 20 |
| Bumpers 102384 (sheet of 2) | 2 | |
| Cam screw | 130449 | 8 |
| Cam lock | 119030 | 16 |
| Drawer dowel | 145718 | 8 |
| Wire | 10040242 | 2 |
Steps
- Runners on the side panels — Lay both side panels flat on a soft surface, inside up. Near the top end of each, screw on a cabinet runner from the 2 runner sets, wheel at the front: CL on the left side, CR on the right side. 3 screws 10048881 each. Check: Check the screw: use 10048881 (bag 1), not the screws with a wide flat head.
- CR runner on the middle panel — Lay the middle panel flat between them. Screw a CR cabinet runner near its top end with 3 screws 10048881, wheel at the front.
- Turn it over: CL runner — Turn the middle panel over. Screw the CL cabinet runner onto this face, at the same place, with 3 screws 10048881.
- Glides under the bottom — Lay the bottom panel upside down. Press 6 glides 10061178 into the holes: 3 along the front edge and 3 along the back. Then turn the bottom over onto its glides.
- Dowels in the bottom — Push 4 wooden dowels 101345 into the holes along the back edge of the bottom.
- Right side panel on — Stand the bottom on its front edge, dowels up. Stand the right side panel (CR runner) up on its front edge too, push its 2 pegs into the keyhole slots at the end of the bottom and press it down to lock. Check: Get someone to hold the bottom upright while you work.
- Left side panel on — Stand the left side panel (CL runner) on its front edge at the other end of the bottom, push its pegs into the keyhole slots and press it down.
- Middle panel on — Stand the middle panel on its front edge in the middle, push its 2 pegs into the keyhole slots in the bottom and press it down. Check: The runners of all three panels must be at the open (top) end.
- Dowels in a back panel — Lay one back panel flat, grey side up, and push 4 dowels 101345 into the holes in one long edge. Check: The edge with the dowels points to the open end, away from the bottom.
- Slide in the first back panel — Slide the back panel into the grooves of the side panels from the open end, grey side out, dowels last, all the way down onto the 4 dowels in the bottom.
- Plugs into the middle panel — Push 2 expanding plugs 10050769 through the holes in the back panel into the edge of the middle panel. Then push a pin 10050771 into each plug to spread it.
- Second back panel — Slide the second back panel into the grooves, grey side out, until it sits on the dowels of the first one. Check: Turn it so its small holes are near the open end, as in the manual's close-up.
- Plugs and pins — Fix the second back panel to the middle panel the same way: 2 expanding plugs 10050769, each spread with a pin 10050771.
- Hook on the top — Two people: hold the top on its front edge at the open end, push its 6 keyhole slots over the pegs of the side panels and the middle panel, and press it down to lock.
- Locking screws — Screw a locking screw 10077982 into the hole in the back edge at each end of the top and the bottom with the Allen key 100092. 4 in all.
- Stand it up — With help, tip the sideboard up onto its glides. Check: Two people are needed to stand it up.
- Brackets for the back panel — In each compartment, fix a bracket 10003780 under the top with a screw 105811, then screw its lower end to the upper back panel with another screw 105811. Check: Use the screws 105811 here, not the similar screws 146114.
- Wall brackets under the top — Fix the 2 wall brackets 106989 under the top at the back, near the sides, flange hanging down at the back edge. Use a washer 100823 and a screw 109049 for each.
- Mark the wall — Push the sideboard against the wall where it will stand. Mark the wall with a pencil through the slot in each wall bracket. Check: The sideboard can tip over: fix it to the wall. The plugs suit most solid and hollow walls; in solid wood use the screws without plugs.
- Drill and plug the wall — Pull the sideboard well away from the wall. At each mark drill an 8 mm hole about 70 mm deep and tap in a wall plug 121714 with a hammer. Check: In solid wood drill a 3 mm hole and use the screw without a plug.
- Push it back to the wall — Push the sideboard back against the wall, so the slots of the wall brackets line up with the plugs.
- Screw it to the wall — Push each wall bracket back against the wall and tighten its screw. Then put a washer 100823 on a screw 109048 and drive it through the bracket slot into the plug. Do both brackets.
- Shelf supports — Press 8 shelf supports 10051660 into the holes at the same height in each compartment: 2 in each side panel and 2 in each face of the middle panel.
- Shelves — Tilt each shelf into its compartment, lay it on the 4 supports and press it down so the supports grip it.
- Hinges on the doors — Lay the 4 doors face down. Press a hinge 10071303 into each of the 2 round holes per door, arm pointing out past the long edge, and tighten its 2 screws.
- Hang the doors — Two people: hold each door open against its side or the middle panel and screw its 2 hinge plates on with the screws already in them. The doors with the hinges on the middle panel go next to each other.
- Door handles — Hook a handle 10071494 over the top edge of each door, on the edge where the doors meet, and screw it on from the inside with 2 screws 146114.
- Bumpers, close the doors — Stick 4 bumpers 102384 on the front edges of the shelves, 2 where each pair of doors meets. Then close the doors.
- Drawers: cam screws in the fronts — Make 2 drawers (steps 26-35). Lay each drawer front face down and screw 4 cam screws 130449 into the holes near its ends.
- Drawer sides — Put the 2 sides onto the cam screws of each front, grooves at the bottom and towards the inside.
- Lock the sides — Push 4 cam locks 119030 into the holes on the outsides of the drawer sides, arrows towards the front, and turn each one clockwise to lock the cam screws.
- Drawer bottom — Slide the drawer bottom down the grooves of the sides until it sits in the groove of the front.
- Wire on the drawer back — Lay the drawer back flat, groove up. Tap the wire 10040242 into the 2 holes next to the groove with a hammer, hooks pointing away from the groove.
- Drawer back on — Turn the back over and lower it onto the ends of the sides, wire inside, so the drawer bottom goes into its groove.
- Drawer dowels — Push 4 dowels 145718 through the holes in the sides into the ends of the back.
- Lock the back — Push 4 cam locks 119030 into the holes in the back and turn each one clockwise to lock the dowels.
- Drawer runners — Turn each drawer upright. Fit the DL runner under the left side and DR under the right side, hooked into the front, and fix each with 2 screws 146114.
- Drawer handles — Hook a handle 10071494 over the middle of the top edge of each drawer front and screw it on from the inside with 2 screws 146114.
- Drawers in — Lift each drawer level with its opening, set its runner wheels behind the wheels of the cabinet runners and push it all the way in.
- Done! — Your VIHALS sideboard is finished and fixed to the wall. The shelves can be moved to other heights on the supports.
VIHALS sideboard: questions and answers
How long does it take to assemble the IKEA VIHALS sideboard?
About 2.5–3.5 hours for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the VIHALS sideboard?
Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (for the wall plugs).
Can one person assemble the VIHALS sideboard?
It is planned as a 2-person build. One person can do most of it, but get help for steps 3, 4 and 14, where the furniture is lifted or turned.
Does the VIHALS sideboard need to be fixed to the wall?
The manual shows a wall fixing: see step 18 (Wall brackets under the top) and step 19 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the VIHALS sideboard once assembled?
140x37x75 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the VIHALS sideboard?
132 fittings of 21 kinds, the most numerous being 20 × screw, 16 × cam lock, 12 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA VIHALS sideboard assembly instructions PDF?
The official PDF is manual AA-2283730-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 304.917.18 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2283730-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner set 10060247). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA VIHALS chair assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
- IKEA EKET cabinet assembly instructions
All IKEA VIHALS assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained