Step by StepAssembly Find your furniture

IKEA VIHALS chair assembly instructions

How to assemble the IKEA VIHALS chair, step by step: 9 animated steps built from the official manual, about 15–20 min for 1 person, with ring spanner (included).

IKEA VIHALS chair, assembled

Dining chair with a white steel tube frame and a padded beige-grey seat and backrest that click on, held together by four bolts. Size: 49×55 cm, 81 cm high, seat height 48 cm (19 1/4×21 5/8", 31 7/8" high). About 15–20 min, 1 person. Tools: Ring spanner (included).

Based on the official IKEA manual AA-2515910-1 (PDF). Guide updated .

VIHALS chair: quick facts
Steps9
Time15–20 min
People1
ToolsRing spanner (included)
Size49×55 cm, 81 cm high, seat height 48 cm (19 1/4×21 5/8", 31 7/8" high)
Official manualAA-2515910-1
IKEA article number605.951.25
Pieces in the box15

In the box

PartPart numberQuantity
Side frame2
Front cross rail (with middle hole)1
Back cross rail (shorter)1
Backrest1
Seat1
Bolt1286544
Flange nut1048754
Ring spanner1081841

Steps

  1. Put the front rail on the first side frame — Lay both side frames flat with their stubs facing up. Take the cross rail that has a hole in the middle (the longer one) and push it down over the front stub of one frame, next to the rounded corner. The hex hole at its end faces the backrest end of the frame. Check: The two rails look alike: the one with the middle hole goes at the front.
  2. Put the back rail on the same frame — Push the shorter cross rail (no middle hole) down over the other stub of the same frame, the one nearer the back post, again with its hex hole facing the backrest end.
  3. Add the second side frame — Turn the second side frame over so its stubs face down, hold it above the first frame with the legs and posts lined up, and lower it so both stubs go into the tops of the rails.
  4. Fit the bolts and nuts — At each of the 4 joints push a bolt 128654 into the hex hole from the backrest side and screw a nut 104875 onto it from the other side by hand. Leave them loose for now. Check: The bolt head must sit down inside the hex recess, flush with the tube, not stand out.
  5. Stand the chair up and fit the backrest — Turn the chair over onto its four legs. Hold the backrest above the two post tops and push it straight down onto them until it clicks.
  6. Tighten the nuts — Tighten the 4 nuts under the rail ends with the ring spanner 108184, turning it clockwise as seen from below, until the joints are firm.
  7. Hook the seat onto the front rail — Hold the seat with its back edge raised. Lower its front onto the front rail and slide it back a little so the 2 front clips hook under the rail.
  8. Press the seat down — Press the back of the seat down until the 2 back clips click over the back rail. Check from below that all 4 clips are fully in place.
  9. Done! — Your VIHALS chair is ready. It is tested for 110 kg. Check the nuts now and then and tighten them again if needed. The covers can be unzipped and taken off for washing.

VIHALS chair: questions and answers

How long does it take to assemble the IKEA VIHALS chair?

About 15–20 min for 1 person, working through the 9 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the VIHALS chair?

Ring spanner (included). Already in the box: Ring spanner.

Can one person assemble the VIHALS chair?

Yes, it is a one-person build.

What size is the VIHALS chair once assembled?

49×55 cm, 81 cm high, seat height 48 cm (19 1/4×21 5/8", 31 7/8" high), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the VIHALS chair?

8 fittings of 2 kinds, the most numerous being 4 × bolt, 4 × flange nut. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA VIHALS chair assembly instructions PDF?

The official PDF is manual AA-2515910-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 605.951.25; other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2515910-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 128654). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA VIHALS assembly guides · All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained