Step by StepAssembly Find your furniture

IKEA MARIEDAMM table assembly instructions

How to assemble the IKEA MARIEDAMM table, step by step: 13 animated steps built from the official manual, about 30 min for 2 people, with Allen key (supplied).

IKEA MARIEDAMM table, assembled

Round dining table with a black marble-effect top on 4 crossing bent steel legs, locked together in the middle by a square connector. Size: 105 cm. About 30 min, 2 people. Tools: Allen key (supplied).

Based on the official IKEA manual AA-2521672-2 (PDF). Guide updated .

MARIEDAMM table: quick facts
Steps13
Time30 min
People2
ToolsAllen key (supplied)
Size105 cm
Official manualAA-2521672-2
IKEA article number704.926.45 (black marble effect)
Pieces in the box55

In the box

PartPart numberQuantity
Table top1
Leg4
End cap100823234
Floor cap100822994
Screw1051008
Screw1010871416
Washer10083116
Centre connector100824521
Allen key1000921

Steps

  1. Push an end cap into each leg — Lay the 4 bent legs flat on a rug. Push an end cap (10082323) into the open end of the short arm of each leg, until it sits flush. Check: Work on a rug or the flattened box so the legs and top are not scratched.
  2. Push a floor cap into each leg — Push a floor cap (10082299) into the angled end of the long arm of each leg. The sloped cap sits level with the cut of the tube.
  3. Fit 2 screws in the middle of each leg — Turn 2 screws (105100) into the 2 holes in the middle of the long arm of each leg with the allen key. Do not tighten them: leave the heads standing proud, the centre connector slides under them later. Check: Leave a gap under each screw head. A screw turned in flush stops the centre connector fitting.
  4. Screw the first leg under the top — Lay the top upside down on the rug. Hold the first leg with its short arm flat on one group of 4 holes and screw it on with 4 washers (100831) and screws (10108714) using the allen key. Do not tighten the screws yet. Check: Two people: one holds the leg while the other fits the screws. Leave every screw loose until step 9.
  5. Add the second leg — Bring the second leg in from the side so it crosses under the first one. Place its short arm on the next group of holes and fit 4 washers (100831) and screws (10108714). Leave them loose.
  6. Add the third leg — Fit the third leg the same way, crossing the second one. Fix its short arm with 4 washers (100831) and screws (10108714), still loose.
  7. Add the fourth leg — Fit the last leg so it crosses the third leg and the first. Fix it with 4 washers (100831) and screws (10108714), still loose. The 4 legs now meet in the middle.
  8. Push on the centre connector — Push the centre connector (10082452) down over the point where the 4 legs cross, so the 8 screw heads standing proud slide into the slots in its walls.
  9. Tighten the 8 screws in the connector — Reach into the connector with the allen key and tighten all 8 screws (105100), so the connector clamps the 4 legs together.
  10. Tighten the screws of the first 2 legs — Now that the legs are locked together, tighten the 4 screws (10108714) of the first leg firmly with the allen key, then the 4 of the second leg, so the washers are pressed flat.
  11. Tighten the screws of the other 2 legs — Tighten the 8 screws (10108714) of the third and fourth leg the same way. All 16 screws under the top are now tight.
  12. Turn the table over — With two people, lift the table and turn it over onto its legs. Lift it rather than dragging it, so the legs are not loaded sideways.
  13. Done! — Your MARIEDAMM table is ready.

MARIEDAMM table: questions and answers

How long does it take to assemble the IKEA MARIEDAMM table?

About 30 min for 2 people, working through the 13 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the MARIEDAMM table?

Allen key (supplied). Already in the box: Allen key.

Can one person assemble the MARIEDAMM table?

It is planned as a 2-person build. One person can do most of it, but get help for step 12, where the furniture is lifted or turned.

What size is the MARIEDAMM table once assembled?

105 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the MARIEDAMM table?

49 fittings of 6 kinds, the most numerous being 16 × screw, 16 × washer, 8 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA MARIEDAMM table assembly instructions PDF?

The official PDF is manual AA-2521672-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 704.926.45 (black marble effect); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2521672-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example end cap 10082323). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All tables assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained