Step by StepAssembly Find your furniture

IKEA FJÄLLBO shelving unit assembly instructions

How to assemble the IKEA FJÄLLBO shelving unit, step by step: 31 animated steps built from the official manual, about 1.5–2 hours for 2 people, with Phillips screwdriver, spirit level.

IKEA FJÄLLBO shelving unit, assembled

Black steel frame on six posts with a wooden top and middle shelf, a perforated steel bottom shelf and side panels, and two perforated doors. Size: 100x95 cm. About 1.5–2 hours, 2 people. Tools: Phillips screwdriver, Spirit level.

Based on the official IKEA manual AA-1926910-5 (PDF). Guide updated .

FJÄLLBO shelving unit: quick facts
Steps31
Time1.5–2 hours
People2
ToolsPhillips screwdriver, Spirit level
Size100x95 cm
Official manualAA-1926910-5
IKEA article number503.392.92 (black)
Pieces in the box100

In the box

PartPart numberQuantity
Side frame (2 posts + perforated panel)2
Perforated bottom shelf1
Middle rail2
Middle post2
Middle shelf (smaller board)1
Top board (larger board)1
Top frame1
Curved brace4
Door catch plate1
Perforated door2
Adjustable foot1221586
Screw1392124
Screw10761639
Screw15249716
Screw1525274
Sleeve nut1525264
Angle bracket1527302
Hinge1533344
Magnet1395782
Screw1147552

Steps

  1. Right side frame and bottom shelf — The frame is built lying on its back. Lay the right side frame on a rug with its perforated panel standing up, front post on top and the short leg ends towards you. Fit the perforated bottom shelf, standing on its long edge, into the two cradles at the bottom of the side frame. Line up the holes. Check: Work on a rug or the flattened box so the black finish does not get scratched.
  2. Screw the back corner — Fix the back corner of the bottom shelf with 1 screw (107616) through the cradle on the side frame. Turn it in clockwise with a Phillips screwdriver.
  3. Back middle rail — Take a middle rail and lay it on the floor at the back, at the top edge of the perforated side panel, with its tabs pointing up. Slide its end into the cradle on the side frame.
  4. Screw the back rail — Fix the end of the back rail with 1 screw (107616) through the cradle.
  5. Back middle post — Slide one of the two loose posts in under the bottom shelf and the back rail, in the middle, threaded end towards you (the leg end). Use the post with 3 evenly spaced holes for the back. Check: The two loose posts differ: the back one has 3 evenly spaced holes. The end with the threaded insert is the bottom.
  6. Bottom shelf to the back post — Fix the bottom shelf to the back middle post with 1 long screw (139212), through the back tube of the shelf into the post.
  7. Bracket on the back rail — Put an angle bracket (152730) on the back rail over the middle post, round hole on the rail and the slotted flange standing up along its edge towards the open top end. Fix it with 1 long screw (139212) through the rail into the post. Check: Check the bracket's direction: the round hole lies on the rail, the slotted flange stands up.
  8. Front middle rail — Fit the second middle rail at the front, on top, with its tabs pointing down. Slide its end into the upper cradle of the side frame.
  9. Left side frame — With a second person, lift the left side frame and push it onto the free ends of the bottom shelf and the two rails, so they go into its cradles. Check: Two people needed: the frame is long and the joints must go in together.
  10. 4 screws for the left frame — Fix the joints with 4 screws (107616) through the cradles: the front rail, the back rail and the bottom shelf on the left, and the front rail on the right.
  11. Bottom braces — Hold a curved brace under each front corner of the bottom shelf, curve towards the leg, and fix each one with 2 screws (107616) into the shelf.
  12. Braces to the front posts — Join each brace to its front post: push 2 sleeve nuts (152526) in from the front of the post and screw 2 screws (152527) in from the brace side, into the sleeve nuts. Check: The sleeve nuts go in from the post side, the screws from the brace side, not the other way round.
  13. Front middle post — Lay the other loose post on top, in the middle of the front, threaded end at the leg end. Check: The threaded insert for the foot goes at the bottom (leg) end.
  14. Bottom shelf to the front post — Fix the bottom shelf to the front middle post with 1 long screw (139212), from inside through the front tube of the shelf into the post.
  15. Bracket on the front rail — Hold the second angle bracket (152730) under the front rail at the middle post, slotted flange hanging down along its edge towards the open top end, and fix it with 1 long screw (139212) through the rail into the post.
  16. Middle shelf — Take the smaller of the two wooden boards. Tilt it in from the open top end and lay it on the two middle rails, so it rests on all the tabs. Check: Use the smaller board here; the larger one is the top.
  17. 8 screws in the middle shelf — Fix the middle shelf with 8 short screws (152497), turned in through the slotted tabs into the underside of the board: 3 along the back, 1 in each side frame and 3 along the front.
  18. Door catch plate — Hold the catch plate under the front middle post, just below the front rail, raised middle against the post and the wings on either side. Fix it with 1 screw (107616). Check: Check the direction: the raised middle goes against the post.
  19. Feet, then stand it up — Screw an adjustable foot (122158) into the bottom of each of the 6 posts by hand. Then, with two people, stand the frame up on its feet. Check: Lift it up, don't drag it over the floor.
  20. Top frame on the top board — Lay the larger wooden board face down on the rug. Put the top frame on it with the U-shaped sockets pointing up, and its outer edges level with the edges of the board. Check: The flat side of the frame goes on the board, not the side with the sockets.
  21. 8 screws in the top — Fix the top frame to the board with 8 short screws (152497) through the tabs: 2 along each long bar and 2 in each end.
  22. Top onto the posts — Turn the top over and lower it onto the frame so the 6 post ends go into the 6 sockets. Check: Two people make this easier.
  23. 3 screws into the back posts — From inside, fix the top of each post in its socket with 1 screw (107616). Start with the 3 back posts.
  24. 3 screws into the front posts — Then fix the 3 front posts the same way, 1 screw (107616) each from inside: 6 screws in total.
  25. Top braces — Fix a curved brace in each top front corner, on the front of the post and the top frame, with 3 screws (107616) each. Its top edge sits level with the top frame. Check: The top edge of the brace must line up with the top frame.
  26. Level it — Put the unit where it will stand, against the wall. Check it with a spirit level and turn the 6 feet in or out until it stands level and steady.
  27. Hinges on the doors — Lay the two perforated doors face up. Screw 2 hinges (153334) to the outer edge of each door, 2 screws (107616) per hinge, with the second leaf sticking out past the edge.
  28. Hang the doors — Hold each door in its opening and screw the free hinge leaves to the front of the corner post with 2 screws (107616) each.
  29. Magnets in the doors — Open the doors. Screw a magnet (139578) to the inside of each door at the top corner by the middle post, with a screw (114755). Close the doors: the magnets hold them on the catch plate. Check: If the doors do not line up, push the frame square and adjust the hinges (info on manual pages 26-27).
  30. Fix it to the wall — Fix the unit to the wall with 2 screws through the holes near the top of the two back corner posts. Use pan-head screws (not countersunk) and plugs that suit your wall. Check: Must be fixed to the wall to prevent tip-over. Wall screws and plugs are not included.
  31. Done! — Your FJÄLLBO shelving unit is assembled and fixed to the wall. Max load: 34 kg per shelf.

FJÄLLBO shelving unit: questions and answers

How long does it take to assemble the IKEA FJÄLLBO shelving unit?

About 1.5–2 hours for 2 people, working through the 31 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the FJÄLLBO shelving unit?

Phillips screwdriver, spirit level.

Can one person assemble the FJÄLLBO shelving unit?

It is planned as a 2-person build. One person can do most of it, but get help for steps 9, 19 and 22, where the furniture is lifted or turned.

Does the FJÄLLBO shelving unit need to be fixed to the wall?

The manual shows a wall fixing: see step 30 (Fix it to the wall) and step 31 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the FJÄLLBO shelving unit once assembled?

100x95 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the FJÄLLBO shelving unit?

83 fittings of 10 kinds, the most numerous being 39 × screw, 16 × screw, 6 × adjustable foot. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA FJÄLLBO shelving unit assembly instructions PDF?

The official PDF is manual AA-1926910-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 503.392.92 (black); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1926910-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example adjustable foot 122158). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA FJÄLLBO assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained