IKEA SKOGSTA dining table assembly instructions
How to assemble the IKEA SKOGSTA dining table, step by step: 21 animated steps built from the official manual, about 1 h for 2 people, with Allen key 100092 + handle 121030 (included), flat-blade screwdriver.
Large solid acacia dining table with a two-piece top on two black leaning leg frames, joined by a long stretcher and a V-shaped brace. Size: 235×100 cm. About 1 h, 2 people. Tools: Allen key 100092 + handle 121030 (included), Flat-blade screwdriver.
Based on the official IKEA manual AA-1984886-6 (PDF). Guide updated .
| Steps | 21 |
|---|---|
| Time | 1 h |
| People | 2 |
| Tools | Allen key 100092 + handle 121030 (included), Flat-blade screwdriver |
| Size | 235×100 cm |
| Official manual | AA-1984886-6 |
| IKEA article number | 704.192.64 (acacia black) |
| Pieces in the box | 91 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Table top half | 2 | |
| Leg | 4 | |
| Top rail | 2 | |
| Lower rail | 2 | |
| Long stretcher | 1 | |
| Diagonal brace | 2 | |
| Leg bracket | 4 | |
| Connector pin | 158454 | 4 |
| Bolt 113152 (long) | 8 | |
| Bolt | 104558 | 14 |
| Barrel nut | 123098 | 8 |
| Washer | 100854 | 8 |
| Dowel | 101350 | 25 |
| Screw | 106553 | 4 |
| Felt pads 114138 (sheet of 4) | 1 | |
| Allen key | 100092 | 1 |
| Allen-key handle | 121030 | 1 |
Steps
- Lay out the two top halves — Lay both halves of the top upside down on a rug or the flattened box, long edges facing each other. Push the 4 connector pins (158454) into the holes in the long edge of one half, up to their collars. Check: Work on a soft surface so the acacia top is not scratched.
- Push the halves together — Slide the two halves together so the pins go into the holes of the other half, until the edges meet along the whole length.
- Dowels in the rails — Each leg frame has a top rail (with 4 slots) and a lower rail (with a notch). Lay the rails on the floor and push 2 dowels (101350) into each end of every rail: 16 dowels for the two frames.
- Push the legs onto the rails — Push a leg onto the dowels at each end of the rails, so the rails sit flush with the outer face of the legs. Build both frames the same way.
- Bolt the first frame — Push a barrel nut (123098) into each hole in the inner face of the rails and turn its slot with a flat screwdriver so the hole lines up. Then screw a long bolt (113152) through each leg into the nut with the allen key in its handle. Check: Use the long bolts 113152 here, not 104558.
- Bolt the second frame — Fit the second frame the same way: 4 barrel nuts (123098) lined up with the screwdriver, then 4 long bolts (113152) through the legs, tightened with the allen key.
- Dowels in the leg brackets — Push one dowel (101350) into the hole at the back of each leg bracket, at the end of the long bar: 4 brackets in all.
- Screw on the leg brackets — Put a bracket on the outer face of each leg, over the lower rail bolt, with the dowel end towards the top rail. Fix it with a screw (106553) and the allen key.
- Stand the frames up, top dowels in — Stand both frames up on their feet. Push 2 dowels (101350) into the holes in the middle of each top rail.
- Put the frames on the top — Turn each frame upside down and lower it onto the top, dowels into the holes near the ends. The legs must lean outwards, away from the middle of the table. Check: Check the lean: a frame put on the wrong way round has its legs leaning in towards the middle.
- Bolt the frames to the top — Put a washer (100854) on each of 8 bolts (104558) and screw them through the slots of the top rails into the top with the allen key: 4 per frame. Check: The washer must lie flat under the bolt head.
- Fit the long stretcher — Feed one end of the stretcher under the left lower rail, lower the other end and slide it under the right rail, so it lies in both notches with its ends sticking out a little. Fix it with a bolt (104558) through each lower rail.
- Join the two braces — Push a dowel (101350) into the end of one brace and push the second brace onto it, so the two braces form a V.
- Put the V brace under the stretcher — Turn the V point up and slide it in under the stretcher from the side, held at an angle so the ends pass between the legs. Turn it straight so the ends meet the top rails, then push the point up against the stretcher.
- Bolt the stretcher to the brace — Screw 2 bolts (104558) through the stretcher into the point of the V with the allen key.
- Bolt the brace to the left frame — From the outside, screw a bolt (104558) through the middle of the left top rail into the end of the brace.
- Bolt the brace to the right frame — Do the same at the other end: a bolt (104558) through the right top rail into the other end of the brace.
- Felt pads on the feet — Peel the 4 felt pads (114138) off the sheet and press one firmly onto the end of each foot.
- Tighten the 8 frame bolts again — Go round the 8 bolts that hold the frames to the top and tighten each one again with the allen key, until the washer is pressed flat. Check: Check that every washer lies flat and is not bent.
- Turn the table over — With two people, lift the table by the frames, tip it onto one long edge and then lower it onto its feet. Lift it; do not drag it on its legs. Check: This needs two people: the table is long and heavy.
- Done! — Your SKOGSTA dining table is ready.
SKOGSTA dining table: questions and answers
How long does it take to assemble the IKEA SKOGSTA dining table?
About 1 h for 2 people, working through the 21 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the SKOGSTA dining table?
Allen key 100092 + handle 121030 (included), flat-blade screwdriver. Already in the box: Allen key 100092 + handle 121030.
Can one person assemble the SKOGSTA dining table?
It is planned as a 2-person build. One person can do most of it, but get help for steps 9 and 20, where the furniture is lifted or turned.
What size is the SKOGSTA dining table once assembled?
235×100 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the SKOGSTA dining table?
64 fittings of 7 kinds, the most numerous being 25 × dowel, 14 × bolt, 8 × barrel nut. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA SKOGSTA dining table assembly instructions PDF?
The official PDF is manual AA-1984886-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 704.192.64 (acacia black); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1984886-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example connector pin 158454). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA SKOGSTA chair assembly instructions
- IKEA LACK side table assembly instructions
- IKEA LACK coffee table assembly instructions
- IKEA NORDEN gateleg table assembly instructions
- IKEA KVISTBRO storage table assembly instructions
- IKEA LISABO table assembly instructions
- IKEA TÄRNÖ table, outdoor assembly instructions
- IKEA TINGBY side table on castors assembly instructions
All IKEA SKOGSTA assembly guides · All tables assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained