Step by StepAssembly Find your furniture

IKEA STÄLL shoe cabinet with 4 compartments assembly instructions

How to assemble the IKEA STÄLL shoe cabinet with 4 compartments, step by step: 34 animated steps built from the official manual, about 2–3 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver, hammer, drill with 8 mm bit (for the wall plugs), pencil.

IKEA STÄLL shoe cabinet with 4 compartments, assembled

A very slim white shoe cabinet with four tilt-out compartments: you build the frame face down, add the legs, fix it to the wall, then hook in the four compartments. Size: 96x17x90 cm. About 2–3 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Drill with 8 mm bit (for the wall plugs), Pencil.

Based on the official IKEA manual AA-2341972-6 (PDF). Guide updated .

STÄLL shoe cabinet with 4 compartments: quick facts
Steps34
Time2–3 hours
People1
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Drill with 8 mm bit (for the wall plugs), Pencil
Size96x17x90 cm
Official manualAA-2341972-6
IKEA article number605.302.66 (white)
Pieces in the box154

In the box

PartPart numberQuantity
Side panel2
Bottom panel1
Top panel1
Centre divider1
Back rail1
Front leg2
Plinth rail1
Base runner2
Compartment door4
Plastic compartment body101301014
End piece101301234
End piece101300984
Hex key1000011
Connector screw1002144
Screw10034724
Pivot bracket100998778
Guide knob100970278
Dowel10135019
Cam screw11833116
Cam lock11813716
Angle bracket1027152
Screw1095034
Screw1095771
Glide1535522
Screw15193016
Wall screw1090482
Washer1008232
Wall plug1217142

Steps

  1. Divider onto the bottom — Lay the panels on a soft surface. Stand the bottom panel on its long edge and push 2 dowels 101350 into the end of the centre divider. Push the divider onto the middle of the bottom panel, square to it. Check: The bottom panel has two holes in the middle of its outer face; that face goes outwards.
  2. Screw the divider — Drive a connector screw 100214 through the larger centre hole of the bottom panel into the end of the divider, with the hex key 100001. Turn it clockwise until it is tight.
  3. Cam screws — Screw cam screws 118331 into the small holes shown: 3 in each side panel (2 at one end, 1 near the middle) and 6 in the top (2 at each end, 2 in the middle). Turn them in until the collar sits on the board.
  4. Pivot brackets — Fix 8 pivot brackets 10099877, each with 2 screws 100347: 2 on the inner face of each side panel and 2 on each face of the divider, in the pre-drilled holes near the front edge. The hooks open towards the front edge.
  5. Guide knobs — Fix a guide knob 10097027 above each pivot bracket, peg in the hole, with 1 screw 100347 each. 8 in all: 2 per side panel and 2 on each face of the divider.
  6. First side panel — Push 2 dowels 101350 into one end of the bottom panel. Stand a side panel on its front edge, brackets inwards, and push it onto the dowels so its two cam screws go into the holes in the end of the bottom panel.
  7. Lock the side panel — Push 2 cam locks 118137 into the large holes at that end of the bottom panel, arrow towards the edge, and turn them clockwise with a flat-blade screwdriver to pull the side panel tight.
  8. Back rail and second side — Push 2 dowels 101350 into each end of the back rail and 2 into the free end of the bottom panel. Lay the rail flat across the back, onto the divider, its dowels in the side panel. Then push the second side panel onto the bottom and the rail.
  9. Lock the rail and the bottom — Push 4 cam locks 118137 into the large holes: 2 in the back face of the rail, near its ends, and 2 at the new end of the bottom panel. Turn them all clockwise.
  10. Screw the rail to the divider — Drive a connector screw 100214 through the middle hole of the back rail into the back edge of the divider with the hex key 100001.
  11. Put the top on — Push 5 dowels 101350 into the top ends: 2 in each side panel and 1 in the divider. Stand the top on its front edge, cam screws towards the frame, and push it onto the dowels.
  12. Lock the top — Push 6 cam locks 118137 into the large holes near the top end: 2 in each side panel and 2 in the divider, on the inside. Turn them clockwise to pull the top tight.
  13. Cam screws in the legs — Screw 2 cam screws 118331 into each front leg: one in the small hole of its inner side face and one in the end that faces the back.
  14. Plinth rail — Push a dowel 101350 into the inner side face of each leg. Lay the plinth rail between the legs and push the legs onto its ends.
  15. Lock the plinth rail — Push 2 cam locks 118137 into the holes near the ends of the plinth rail and turn them clockwise.
  16. Angle brackets on the runners — Screw an angle bracket 102715 onto one end of each base runner with a screw 109503, its free leg standing up.
  17. Runners onto the legs — Push a dowel 101350 into the back end of each leg. Stand a runner on each leg, bracket at the top and facing inwards, on the dowel and the cam screw.
  18. Lock the runners — Push a cam lock 118137 into the hole in the inner face of each runner, near the leg, and turn it clockwise.
  19. Fix the base — Slide the base up against the underside of the bottom panel, legs at the front edge. Screw the 2 angle brackets to the bottom panel with screws 109503, then drive the long screw 109577 through the middle of the plinth rail into the bottom panel.
  20. Turn it onto its back — Turn the cabinet over its side panel so it lies on its back, open front up. Check: Get help or work slowly: the frame is long and the legs stick out.
  21. Screw the legs from inside — Inside the cabinet, drive a connector screw 100214 through each front corner of the bottom panel into the leg below, with the hex key 100001.
  22. Glides — Tap a glide 153552 into the hole in the foot of each leg with a hammer.
  23. Stand it up by the wall — Stand the cabinet up next to where it will go and lean it back against the wall. It only has front legs, so it tips backwards until it is screwed to the wall: keep a hand on it. Check: STÄLL must be fixed to the wall. Never leave it standing free.
  24. Plugs in the wall — Mark 2 holes on the wall where the cabinet will stand: 63 cm up and 66 cm apart, level and centred on its place (the holes in the back rail). Drill them (8 mm for the plugs supplied) and tap in the 2 plugs 121714. Check: The screws and plugs suit most solid and hollow walls. In solid wood use the screws without plugs. If unsure, ask a professional.
  25. Slide it into place — Slide the cabinet along the wall in front of the plugs, so the holes in the back rail line up with them. Keep its back against the wall.
  26. Screw it to the wall — Put a washer 100823 on each long screw 109048 and drive them through the holes in the back rail into the plugs, one in each column, until the cabinet sits tight against the wall. Check: Use the long screws 109048 here, not the screw 109577.
  27. Fold the compartment bodies — Stand each plastic body 10130101 on its end. Fold the narrow flap along its hinge line so it stands at a right angle to the perforated wall, the way the arrow shows (not the other way).
  28. First end pieces — Press an end piece 10130123 down onto the top end of each body until it clicks onto the clips.
  29. Second end pieces — Turn each body end for end and press an end piece 10130098 onto the other end until it clicks.
  30. Bodies onto the doors — Lay the 4 doors face down, finger notch away from you. Lower a body onto each door, perforated wall up and the folded flap at the door's lower edge, so the pegs on the flap go into the holes in the door. Check: Never let anyone climb on or hang from an open compartment.
  31. Screw the end pieces — Fix each compartment with 4 screws 151930, through the tabs of the end pieces into the door. Use a hand screwdriver, not a power drill. Check: No power drill: the screws strip the door easily.
  32. Hook in a compartment — Hold a compartment tilted open, finger notch up, and push it into an opening: the pins at its lower corners go into the pivot brackets and the curved arms run under the guide knobs. Then tilt it closed.
  33. The other three compartments — Hook in the other 3 compartments the same way, tilted open, then tilt each one closed.
  34. Done! — Your STÄLL is finished and fixed to the wall. Pull a door at its finger notch to tilt the compartment open, stand your shoes inside and push it closed again.

STÄLL shoe cabinet with 4 compartments: questions and answers

How long does it take to assemble the IKEA STÄLL shoe cabinet with 4 compartments?

About 2–3 hours for 1 person, working through the 34 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the STÄLL shoe cabinet with 4 compartments?

Phillips screwdriver, flat-blade screwdriver, hammer, drill with 8 mm bit (for the wall plugs), pencil.

Can one person assemble the STÄLL shoe cabinet with 4 compartments?

Yes, it is a one-person build.

Does the STÄLL shoe cabinet with 4 compartments need to be fixed to the wall?

The manual shows a wall fixing: see step 24 (Plugs in the wall) and step 34 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the STÄLL shoe cabinet with 4 compartments once assembled?

96x17x90 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the STÄLL shoe cabinet with 4 compartments?

139 fittings of 19 kinds, the most numerous being 24 × screw, 19 × dowel, 16 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA STÄLL shoe cabinet with 4 compartments assembly instructions PDF?

The official PDF is manual AA-2341972-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 605.302.66 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2341972-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example plastic compartment body 10130101). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All hallway assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained