Step by StepAssembly Find your furniture

IKEA BISSA shoe cabinet with 2 compartments assembly instructions

How to assemble the IKEA BISSA shoe cabinet with 2 compartments, step by step: 27 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver, hammer, spirit level, drill with 8 mm bit (for the wall plugs).

IKEA BISSA shoe cabinet with 2 compartments, assembled

A slim white shoe cabinet with two tilt-out compartments: you build the frame lying on its side, stand it on its top, lay it face down to put in the two compartments, then fix it to the wall. Size: 49x28x93 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Spirit level, Drill with 8 mm bit (for the wall plugs).

Based on the official IKEA manual AA-2324659-5 (PDF). Guide updated .

BISSA shoe cabinet with 2 compartments: quick facts
Steps27
Time1–1.5 hours
People1
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Spirit level, Drill with 8 mm bit (for the wall plugs)
Size49x28x93 cm
Official manualAA-2324659-5
IKEA article number705.302.56 (white)
Pieces in the box98

In the box

PartPart numberQuantity
Side panel2
Top1
Back rail2
Plinth rail1
Compartment door2
Plastic fan4
Compartment bottom (widest board)2
Back strip (narrowest board)2
Shoe rest (middle-width board)2
Cam screw11833110
Cam lock11822410
Dowel10135010
Felt pad1078494
Tilt-stop pin100970274
Screw1003474
Screw11279216
Screw10953512
Bush100950654
Wall screw1090482
Wall plug1217142
Washer1008232

Steps

  1. Cam screws into the panels — Lay the two side panels and the top on a soft surface, inner faces up. Screw a cam screw 118331 into each small hole shown: 3 in each side panel (along the edges, for the rails) and 4 in the top, near its ends. Turn them in until the collar sits on the board.
  2. Tilt-stop pins — Tap a tilt-stop pin 10097027 into the 2 holes near the front edge of each side panel with a hammer, its plate on the screw-hole side. Then fix each plate with a small screw 100347. Check: The pins hold the compartments: put one in each of the 4 holes.
  3. Two back rails — Push a dowel 101350 into both ends of the two back rails. Stand them on the back edge of the side panel lying in front of you, on its dowel holes and cam screws: one near the top end, one just above the notch at the bottom end. The face with the small holes faces you.
  4. Plinth rail — Push 2 dowels 101350 into the ends of the plinth rail and stand it on the front edge of the side panel, at the bottom end.
  5. Lock the rails at the bottom — Push a cam lock 118224 into the large hole at the lower end of each of the 3 rails, arrow towards the cam screw, and turn it clockwise with a flat-blade screwdriver to pull the rail tight against the side panel.
  6. Put the other side panel on — Turn the second side panel over, inner face down, and lower it onto the 3 rails so their dowels and its cam screws meet. Its notch must be at the same (bottom) end as the first panel's.
  7. Lock the rails at the top — Push 3 more cam locks 118224 into the upper ends of the rails and turn them clockwise.
  8. Stand it on its top end — Set the top aside for a moment. Tip the frame up onto its top end, so it stands upside down with the notched bottom end up.
  9. Onto the top — Lift the frame, push 4 dowels 101350 into the top ends of the side panels and lay the top on the floor under it, cam screws up. Lower the frame onto the top so the dowels and cam screws go into the holes in its ends.
  10. Lock the top — Push 4 cam locks 118224 into the holes near the top (lower) end of both side panels, on the inside, and turn them clockwise.
  11. Felt pads — Hammer a felt pad 107849 into each of the 4 small holes in the bottom ends of the side panels (now at the top).
  12. Lay it face down — Tip the cabinet over onto its front, on a soft surface, so it lies face down with the open back up and the top end towards you.
  13. Fans onto the doors — Lay the 2 doors face down. Stand a plastic fan at each end of a door, its straight edge along the door, the arc towards the door's top, and fix it with 3 screws 112792 (6 per door). Do the same for the second door.
  14. Bottoms into the fans — Take the widest of the three board sizes. Push it down into the clips along the straight edges of the two fans, at the door's bottom edge, until it snaps in. Repeat for the other compartment. Check: Check the board width: the widest boards are the compartment bottoms.
  15. Screw the bottoms — Fix each compartment bottom with 2 screws 109535, one through each fan from the outside.
  16. Back strips into the fans — Take the narrowest boards. Press one into the clips at the tips of the two fans of each compartment, so it runs along their back edges.
  17. Screw the back strips — Fix each back strip with 2 screws 109535 through the tips of the fans.
  18. Top compartment in — Tilt a compartment, door down and its top edge lowest, and lower it into the open back between the two back rails. Slide its top edge under the upper rail towards the top, then lay it down flat. The fans must go under the tilt-stop pins on the side panels. Check: Check both pins: the fan edge must be under the pin, not on top of it.
  19. Bottom compartment in — Feed the second compartment in through the open bottom end, door down, over the plinth rail, and slide it into the bottom opening under the pins.
  20. Let the compartment drop in — Lift the bottom end of the cabinet a little and set it down again, so the bottom compartment drops off the plinth rail. Both doors must lie flat and flush with the front edges of the sides.
  21. Pivot bushes and screws — Push a bush 10095065 into the pivot hole of each fan from inside the compartment, then drive a screw 112792 through each bush into the side panel. 4 in all. Tighten them by hand. Check: Don't use a power drill here: overtightened pivots stop the compartments tilting.
  22. Stand it up — Tip the cabinet back up onto its feet, near the wall where it will stand.
  23. Level it, plugs in the wall — Check the top with a spirit level. Mark the 2 holes of the upper back rail on the wall, drill them (8 mm for the plugs supplied) and tap in the 2 plugs 121714. Then push the cabinet back against the wall. Check: BISSA must be fixed to the wall. The plugs suit most solid and hollow walls; in solid wood use the screws without plugs. The notches at the back fit over a skirting board.
  24. Screw it to the wall — Tilt the top compartment open. Through the gap, put a washer 100823 on each screw 109048 and screw them through the holes in the upper back rail into the plugs.
  25. Shoe rests — Tilt both compartments fully open. Slide a middle-width board into each one, onto the ledges inside the fans (3 positions to choose from), and fix it with 2 screws 109535 from the outside of the fans.
  26. Close the compartments — Tilt both compartments closed.
  27. Done! — Your BISSA is finished and fixed to the wall. Pull the top of a door to tilt a compartment open, stand your shoes inside, and push it closed again.

BISSA shoe cabinet with 2 compartments: questions and answers

How long does it take to assemble the IKEA BISSA shoe cabinet with 2 compartments?

About 1–1.5 hours for 1 person, working through the 27 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BISSA shoe cabinet with 2 compartments?

Phillips screwdriver, flat-blade screwdriver, hammer, spirit level, drill with 8 mm bit (for the wall plugs).

Can one person assemble the BISSA shoe cabinet with 2 compartments?

Yes, it is a one-person build.

Does the BISSA shoe cabinet with 2 compartments need to be fixed to the wall?

The manual shows a wall fixing: see step 23 (Level it, plugs in the wall) and step 27 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BISSA shoe cabinet with 2 compartments once assembled?

49x28x93 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the BISSA shoe cabinet with 2 compartments?

80 fittings of 12 kinds, the most numerous being 16 × screw, 12 × screw, 10 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BISSA shoe cabinet with 2 compartments assembly instructions PDF?

The official PDF is manual AA-2324659-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 705.302.56 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2324659-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA BISSA assembly guides · All hallway assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained