IKEA BRUSALI shoe cabinet with 3 compartments assembly instructions
How to assemble the IKEA BRUSALI shoe cabinet with 3 compartments, step by step: 27 animated steps built from the official manual, about 1.5–2 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver, hammer, spirit level, wall screws and plugs (not included).
A tall white shoe cabinet with three tilt-out compartments: you build the carcass lying on its side, assemble the three compartments face down, hang them on their pivots, then stand it up and fix it to the wall. Size: 61x30x130 cm. About 1.5–2 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Spirit level, Wall screws and plugs (not included).
Based on the official IKEA manual AA-1010480-15 (PDF). Guide updated .
| Steps | 27 |
|---|---|
| Time | 1.5–2 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Hammer, Spirit level, Wall screws and plugs (not included) |
| Size | 61x30x130 cm |
| Official manual | AA-1010480-15 |
| IKEA article number | 804.803.93 (white) |
| Pieces in the box | 134 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top | 1 | |
| Bottom | 1 | |
| Fixed shelf | 1 | |
| Back rail | 2 | |
| Back strip (niche) | 1 | |
| Compartment door | 3 | |
| Plastic side fan | 6 | |
| Compartment base board | 3 | |
| Compartment back lip | 3 | |
| Shoe rest board | 3 | |
| Front foot 123727/123728 | 2 | |
| Cam screw | 130449 | 16 |
| Cam lock 119252/119250 | 16 | |
| Dowel | 101350 | 6 |
| Tilt stop | 116713 | 6 |
| Screw | 100365 | 6 |
| Screw | 112792 | 26 |
| Screw | 106562 | 18 |
| Bush | 120292 | 6 |
| Knob | 130440 | 3 |
| Screw | 100412 | 3 |
Steps
- Cam screws into the 4 panels — Lay the two side panels, the top and the bottom on a soft surface, inner faces up. Screw a cam screw 130449 into each of the 16 small holes shown: 4 in each side panel, 4 in the top and 4 in the bottom. Stop when the collar sits on the board.
- Tilt stops into the side panels — Hammer a tilt stop 116713 into each of the 3 large holes near the front of both side panels, round stop up. Then fix each stop's plate with a small screw 100365. Check: Use the short screws 100365 here, not the 112792 screws.
- Back rails on dowels — Push a dowel 101350 into both ends of the two back rails. Stand the rails on the side panel lying on the floor, at its back edge: one near the top end, one about a third of the way up from the bottom.
- Lock the rails at the bottom — Push a cam lock 119252 into the hole at the lower end of each rail, slot facing you, and turn it clockwise with a flat-blade screwdriver to pull the rail tight against the side panel.
- Fixed shelf — Lower the fixed shelf onto the side panel at the top end, just above the upper rail. The edge with the groove goes at the back, groove facing the top end of the cabinet. Check: Check the groove: it must face the top end, where the narrow back strip goes later.
- Lock the shelf at the bottom — Push 2 cam locks 119252 into the shelf's face near the side panel and turn them clockwise.
- Put the other side panel on — Turn the second side panel over, inner face down, and lay it on the rails and the shelf so their dowels and cam screws go into its holes. The notch at the back of both side panels must be at the same (bottom) end.
- Lock the rails and shelf at the top — Push 4 cam locks 119252 into the upper ends of the two rails and the shelf, and turn them clockwise.
- Fit the bottom — Stand the bottom panel on its edge at the bottom end of the cabinet, cam screws facing the side panels, and push it on so the cam screws go into the holes in the ends of the side panels.
- Lock the bottom — Push 4 cam locks 119252 into the holes near the bottom end of both side panels, on their inside faces, and turn them clockwise.
- Back strip above the shelf — Slide the narrow back strip in from the open top end, at the back, so it runs in the groove of the fixed shelf.
- Fit the top — Stand the top on its edge at the top end, cam screws towards the cabinet and the groove at the back over the back strip, and push it on.
- Lock the top — Push 4 cam locks 119252 into the holes near the top end of both side panels and turn them clockwise.
- Front feet on dowels — Push a dowel 101350 into the hole inside each front foot. Put the feet on the bottom panel at its two front corners: the left foot 123727 on the left, the right foot 123728 on the right, curved faces to the front.
- Screw the feet on — Fix each foot with a screw 112792 through its hole into the bottom panel. Check: Use the 112792 screws here, not the short 100365 ones.
- Fans onto the 3 doors — Lay the 3 doors face down on a soft surface. Stand a plastic fan at each end of a door, its straight edge along the door's bottom edge, and fix it with 3 screws 112792. Do the same for all three doors. Check: Use the 112792 screws, not the short 100365 ones.
- Base boards into the fans — Push a base board down into the clips along the straight edges of the two fans, at the door's bottom edge. Check its edges match the correct drawing in the manual. Repeat for the other two compartments.
- Screw the base boards — Fix each base board with 2 screws 106562, one through each fan.
- Back lips through the fans — Slide a back lip along its length through the slots at the far corner of the two fans, so it hooks into both clips. Check its edges match the correct drawing. Repeat for the other two compartments.
- Screw the back lips — Fix each back lip with 2 screws 106562 through the fans.
- Hang the bottom compartment — Tilt a compartment open and slide it into the bottom opening (next to the bottom panel), so the hook at the top of each fan goes behind the tilt stop on the side panel.
- Pivot bushes and screws — Push a bush 120292 into the pivot hole of each fan, then drive a screw 112792 through each bush into the side panel. Tighten by hand. Check: Don't use a power drill here: the screws must not be overtightened, or the compartment won't tilt.
- Hang the other 2 compartments — Hang the two remaining compartments in the middle and top openings in the same way, each with 2 bushes 120292 and 2 screws 112792 in its pivots. Check: Again, tighten by hand, no power drill.
- Stand it up and fix it to the wall — Tip the cabinet up onto its feet and push it against the wall. Check with a spirit level that the top is level. Then screw it to the wall with 4 screws through the two back rails, reaching in through the open compartments. Check: BRUSALI must be fixed to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall, with a flat head (not countersunk).
- Shoe rests into the compartments — Put a shoe rest board into each compartment, in whichever of the 3 positions in the fans suits your shoes, with its bevelled edges as shown. Fix it with 2 screws 106562 through the fans.
- Knobs — Tilt the compartments half closed. Hold a knob 130440 on the front of each door, at the hole near the top, and screw it on from behind with a screw 100412. Then tilt the compartments closed.
- Done! — Your BRUSALI is finished and fixed to the wall. Pull a knob to tilt a compartment open, put your shoes in, and push it closed again.
BRUSALI shoe cabinet with 3 compartments: questions and answers
How long does it take to assemble the IKEA BRUSALI shoe cabinet with 3 compartments?
About 1.5–2 hours for 1 person, working through the 27 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the BRUSALI shoe cabinet with 3 compartments?
Phillips screwdriver, flat-blade screwdriver, hammer, spirit level, wall screws and plugs (not included).
Can one person assemble the BRUSALI shoe cabinet with 3 compartments?
Yes, it is a one-person build.
Does the BRUSALI shoe cabinet with 3 compartments need to be fixed to the wall?
The manual shows a wall fixing: see step 24 (Stand it up and fix it to the wall) and step 27 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the BRUSALI shoe cabinet with 3 compartments once assembled?
61x30x130 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the BRUSALI shoe cabinet with 3 compartments?
108 fittings of 11 kinds, the most numerous being 26 × screw, 18 × screw, 16 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA BRUSALI shoe cabinet with 3 compartments assembly instructions PDF?
The official PDF is manual AA-1010480-15, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 804.803.93 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1010480-15. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example front foot 123727). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TRONES shoe cabinet/storage assembly instructions
- IKEA BISSA shoe cabinet with 3 compartments assembly instructions
- IKEA BISSA shoe cabinet with 2 compartments assembly instructions
- IKEA TJUSIG shoe rack assembly instructions
- IKEA STÄLL shoe cabinet with 4 compartments assembly instructions
All hallway assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained