Step by StepAssembly Find your furniture

IKEA HOLMERUD side table assembly instructions

How to assemble the IKEA HOLMERUD side table, step by step: 29 animated steps built from the official manual, about 1–1.5 hours for 1 person, with flat-blade screwdriver, Phillips screwdriver, Allen key (included).

IKEA HOLMERUD side table, assembled

Oak-effect side table with a low bench on one side and a shelved bay on the other, built upside down and on its back with cam locks, dowels and three screws. Size: 80×31×52 cm. About 1–1.5 hours, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Allen key (included).

Based on the official IKEA manual AA-2583944-3 (PDF). Guide updated .

HOLMERUD side table: quick facts
Steps29
Time1–1.5 hours
People1
ToolsFlat-blade screwdriver, Phillips screwdriver, Allen key (included)
Size80×31×52 cm
Official manualAA-2583944-3
IKEA article number405.414.21 (oak effect)
Pieces in the box62

In the box

PartPart numberQuantity
Top1
Bottom board1
Left leg panel1
Right side panel1
Shelf1
Partition1
Rail1
Support rail1
Cam screw11833114
Cam lock11925014
Screw1002143
Wooden dowel10135018
Allen key1000921
Glide1535484

Steps

  1. Cam screws into the bottom board — Lay the bottom board upside down on a soft surface. Screw 2 cam screws into the two holes at one end of its underside, near the long edges.
  2. Dowels into the other end — At the other end of the bottom board, push 2 wooden dowels into the holes in the end edge.
  3. Glides on the left leg panel — Lay the short leg panel flat. Press 2 glides into the holes along one long edge. This edge stands on the floor.
  4. Cam screw into the leg panel — Screw 1 cam screw into the hole in the middle of the leg panel face, the face with the large holes near the other long edge.
  5. Dowels into the leg panel — Push 2 wooden dowels into the holes in the long edge without glides.
  6. Leg panel onto the bottom board — Stand the leg panel on the cam-screw end of the bottom board, glides upwards and the cam screw facing along the board. Press it onto the dowels and cam screws, then turn 2 cam locks clockwise to lock it.
  7. Dowels into the rail — Lay the long narrow rail flat and push 1 wooden dowel into the hole in each end.
  8. Slide the rail into the leg — Stand the rail on its edge along the middle of the bottom board, large holes facing you. Slide it towards the leg panel so its dowel and the cam screw go into its end.
  9. Lock the rail to the leg — Push a cam lock into the large hole in the rail next to the leg panel and turn it clockwise until it grips the cam screw.
  10. Screw the board to the rail — Turn the frame onto its back edge. Drive 1 screw (100214) through the hole in the top face of the bottom board into the edge of the rail with the Allen key.
  11. Glides on the right side panel — Lay the tall side panel flat and press 2 glides into the holes in one short edge. This is its bottom edge.
  12. 5 cam screws into the side panel — Screw 5 cam screws into the small holes on the face of the side panel: 2 near the bottom and 1 between them for the bottom board and rail, 2 higher up for the shelf.
  13. Dowels into the top edge — Push 2 wooden dowels into the holes in the other short edge (the top) of the side panel.
  14. Fit the right side panel — Stand the side panel up at the free end of the bottom board and rail, cam screws facing inwards. Push it on so the dowels and cam screws go into the board and rail ends.
  15. Lock the right side panel — Push 2 cam locks into the large holes in the bottom board and 1 into the rail next to the side panel. Turn each one clockwise until it grips.
  16. Dowels into the shelf — Lay the shelf flat and push 2 wooden dowels into the holes in each end, 4 in total.
  17. Slide the shelf in — Hold the shelf on edge above the bottom board, parallel to it, and slide it along towards the side panel until its dowels and the 2 upper cam screws go into place.
  18. Cam screws into the partition — Lay the partition flat and screw 2 cam screws into the small holes on its face, near one edge.
  19. Dowels into the partition — Push 2 wooden dowels into the holes in the edge of the partition that becomes its top.
  20. Fit the partition — Stand the partition on the bottom board, dowels pointing the same way as the side panel dowels. Slide it onto the free end of the shelf so the shelf dowels and its cam screws engage.
  21. Screw the partition from below — From the underside of the bottom board, drive 2 screws (100214) through the holes either side of the rail up into the partition.
  22. Stand the table up — Tip the table up over its back edge and stand it on its glides.
  23. Lock the shelf — Push 4 cam locks into the large holes on the underside of the shelf, 2 at each end, and turn each one clockwise until it grips.
  24. Dowels into the support rail — Lay the narrow support rail flat and push 2 wooden dowels into each end, 4 in total.
  25. Fit the support rail — Stand the support rail upright beside the partition, in the bench section, and push it straight down into the 2 holes in the bottom board.
  26. Cam screws into the top — Lay the top upside down on a soft surface. Screw 4 cam screws into the small holes on its underside: 2 for the partition and 2 for the side panel.
  27. Lower the top on — Turn the top over, cam screws pointing down, and lower it straight onto the dowels of the partition, support rail and side panel so its cam screws go into their top edges.
  28. Lock the top — Push 4 cam locks into the large holes near the top: 2 in the right face of the partition and 2 in the inner face of the side panel. Turn each one clockwise until it grips.
  29. Done! — Your HOLMERUD side table is assembled. Max load 15 kg on the top and 5 kg on the shelf. Check the fittings now and then and tighten them if needed.

HOLMERUD side table: questions and answers

How long does it take to assemble the IKEA HOLMERUD side table?

About 1–1.5 hours for 1 person, working through the 29 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HOLMERUD side table?

Flat-blade screwdriver, Phillips screwdriver, Allen key (included). Already in the box: Allen key.

Can one person assemble the HOLMERUD side table?

Yes, it is a one-person build.

What size is the HOLMERUD side table once assembled?

80×31×52 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the HOLMERUD side table?

53 fittings of 5 kinds, the most numerous being 18 × wooden dowel, 14 × cam screw, 14 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HOLMERUD side table assembly instructions PDF?

The official PDF is manual AA-2583944-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 405.414.21 (oak effect); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2583944-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All tables assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained