IKEA BILLY bookcase with foldable table assembly instructions
How to assemble the IKEA BILLY bookcase with foldable table, step by step: 42 animated steps built from the official manual, about 2–3 hours for 2 people, with flat & Phillips screwdriver, Allen key (included), drill and wall screws for your wall.
A low BILLY bookcase with a shelf cart on castors inside: pull it out and a hinged tabletop unfolds from the bookcase into a 112 cm deep table. Size: 80x33/112x106 cm. About 2–3 hours, 2 people. Tools: Flat & Phillips screwdriver, Allen key (included), Drill and wall screws for your wall.
Based on the official IKEA manual AA-2568863-4 (PDF). Guide updated .
| Steps | 42 |
|---|---|
| Time | 2–3 hours |
| People | 2 |
| Tools | Flat & Phillips screwdriver, Allen key (included), Drill and wall screws for your wall |
| Size | 80x33/112x106 cm |
| Official manual | AA-2568863-4 |
| IKEA article number | 005.797.55 (white) |
| Pieces in the box | 180 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel with groove | 2 | |
| Top board / fixed shelf | 2 | |
| Back board (top compartment) | 1 | |
| Plinth | 1 | |
| Cart side panel | 2 | |
| Cart shelf / bottom board | 2 | |
| Rail | 1 | |
| Cart back panel | 1 | |
| Rear tabletop | 1 | |
| Front tabletop | 1 | |
| Cam screw | 118331 | 32 |
| Cam lock | 119253 | 32 |
| Wooden dowel | 101351 | 30 |
| Short dowel | 101343 | 4 |
| Screw | 100358 | 36 |
| Bolt | 120925 | 4 |
| Allen key | 100092 | 1 |
| Back-panel fastener 151705 + | 151706 | 12 |
| Wall bracket | 102591 | 2 |
| Wall plate | 103693 | 2 |
| Bracket cover | 102220 | 2 |
| Castor | 10117892 | 2 |
| Wheel | 10118206 | 2 |
| Swing-arm castor | 10121345 | 1 |
| Roller bracket | 10121019 | 2 |
| Hinge | 10081198 | 2 |
Steps
- Dowels into the top-box boards — Use bag 1. Lay the top board, the fixed shelf and the narrow back board on a soft surface. Push 4 long wooden dowels (101351) into the ends of the top board and of the shelf, and 8 into the back board: 2 in each end and 2 in each long edge. 16 in total. Check: Use the long dowels 101351 here, not the short 101343.
- Cam screws into top board and shelf — Turn the top board over. Screw 2 cam screws (118331) into the small holes along one long edge of the top board and 2 into the shelf. Screw them straight in until the collar sits on the surface. Check: The cam screws must stand straight and the collar must not sink into the board.
- Back board onto the shelf — Stand the back board on its long edge on the shelf, cam-lock holes facing out, and push its dowels into the holes along the shelf edge, over the 2 cam screws.
- Top board onto the back board — With two people, turn the top board back over, cam screws pointing down, and press it straight down onto the dowels in the top edge of the back board. Mind your fingers at the joint. Check: Two people. Keep your fingers clear of the joint as you press it down.
- Lock the box and turn it over — Push 4 cam locks (119253) into the large holes of the back board and turn each one clockwise with a flat screwdriver until it grips its cam screw. Then turn the box over onto its end.
- Cam screws into the side panels — Lay both side panels flat, inside up (the face with the curved groove), notched ends the same way. Screw 7 cam screws (118331) into the small holes of each panel, 14 in total.
- Box onto a side panel — Stand the box on end on one side panel, at the end away from the notch, back board along the back edge. Press its dowels into the holes so the cam screws go into the large holes.
- Dowels into the plinth — Push one long wooden dowel (101351) into the hole in each end of the plinth. Check: Use the long dowels 101351.
- Plinth onto the side panel — Stand the plinth on end at the notched end of the side panel, along the back edge, and press its dowel and cam screw into the holes.
- Lock the boards to the lower panel — Push cam locks (119253) into the large holes next to the lower side panel: 2 under the top board, 2 under the shelf and 1 in the plinth. Turn each clockwise until it grips.
- Lock the back board to the lower panel — From behind, push 2 more cam locks into the back board next to the lower side panel and turn them clockwise. That makes 7 on this side.
- Second side panel on top — Turn the second side panel over, groove facing down and notch at the plinth end, and press it straight down onto all the dowels and cam screws.
- Lock the boards to the upper panel — Fit cam locks into the large holes next to the upper side panel: 2 under the top board, 2 under the shelf and 1 in the plinth. Turn each clockwise until it grips.
- Lock the back board to the upper panel — From behind, fit the last 2 cam locks into the back board next to the upper side panel and turn them clockwise. 7 on this side.
- Stand it up at the wall — Tip the bookcase up onto its bottom end and place it against the wall where it will stand. Check: Two people.
- Wall brackets under the shelf — Screw a wall bracket (102591) to the underside of the fixed shelf at each back corner, with 2 screws (100358) each, so its leg hangs down against the wall.
- Fix it to the wall — Hang a wall plate (103693) on each bracket leg and drive a wall screw through it into the wall. Use screws and plugs that suit your wall; they are not included. Check: Must be fixed to the wall to prevent tip-over. Wall screws and plugs are not included.
- Covers over the brackets — Push a cover (102220) over each wall bracket until it clicks.
- Dowels into the cart boards — Use bag 2. Lay out the bottom board, the cart shelf and one cart side panel. Push 4 long dowels (101351) into the ends of the bottom board and of the shelf, and 2 into the top end of the side panel. 10 in total. Check: Long dowels 101351 here, not the short 101343.
- Cam screws into the cart side — Screw 5 cam screws (118331) into the small holes in the inside face of the cart side panel.
- Shelf and bottom board onto the side — Stand the cart shelf and then the bottom board on end on the side panel and press their dowels into the holes, over the cam screws. The bottom board goes near the lower end, the shelf in the middle.
- Short dowels into the rail — Push 2 short dowels (101343) into each end of the rail, 4 in total. Check: Use the short dowels 101343 here.
- Castors onto the rail — Hold the rail on its edge, inside face towards you. Hold a castor (10117892) against the inside face at each end and fix it with 2 bolts (120925) from the other face, tightened with the Allen key.
- Rail onto the cart side — Stand the rail on end at the lower end of the side panel, along its front edge, castors pointing outwards, and press its dowels and cam screw into the holes.
- Lock the cart to the lower side — Push 5 cam locks (119253) into the large holes next to the side panel: 2 in the shelf, 2 in the bottom board, 1 in the rail. Turn each clockwise until it grips.
- Dowels into the second cart side — Lay the second cart side panel flat, inside up, and push 2 long dowels (101351) into its top end.
- Cam screws into the second side — Screw 5 cam screws (118331) into the small holes in its inside face.
- Second side on top — Turn the second side panel over, inside down and dowels at the top end, and press it down onto the shelf, bottom board and rail.
- Lock the cart to the upper side — Fit 5 cam locks into the large holes next to the upper side panel and turn each clockwise until it grips.
- Slide in the back panel — Tip the cart forward onto its front on a soft surface. Slide the back panel in from the top end, along the back edges, until it stops at the bottom board. Check: Stop when the panel reaches the bottom board.
- Rear wheels — Fit a wheel (10118206) in each bottom back corner, inside the side panel. Fix each with 2 screws (100358): one through the tab into the bottom board, one into the side panel.
- Fix the back panel — Push a plug (151706) through the back panel into each of the 12 holes in the bottom board, the shelf and the side panel edges, then press a pin (151705) into each plug.
- Swing-arm castor — Screw the swing-arm castor (10121345) to the underside of the bottom board, near the front, arm pointing to the back, with 4 screws (100358).
- Roller brackets on the rear tabletop — Lay the larger (rear) tabletop face down. Screw a roller bracket (10121019) to each back corner, flush with the edges, with 4 screws (100358) each. Check: Line each bracket up with the edges of the tabletop.
- Front tabletop against it — Lay the smaller (front) tabletop face down and slide it against the long edge of the rear tabletop, away from the brackets.
- Hinge the two tabletops — Lay 2 hinges (10081198) across the joint and screw each down with 8 screws (100358), 4 in each tabletop.
- Cam screws into the front tabletop — Screw 4 cam screws (118331) into the small holes near the side edges of the front tabletop. Check: Mind your fingers at the hinged joint when you lift the tabletop.
- Hook the tabletop into the bookcase — Turn the tabletop over. Slide it into the bookcase under the fixed shelf, rear tabletop first, and drop its rollers into the top of the curved grooves. Hold the front edge up.
- Roll the cart under the tabletop — Stand the cart up on its wheels and roll it in under the front tabletop. Lower the tabletop so the dowels and cam screws go into the tops of the cart side panels.
- Lock the tabletop: left side — Push 2 cam locks (119253) into the large holes just under the tabletop, on the inside of the left cart side panel, and turn each clockwise until it grips.
- Lock the tabletop: right side — Fit the other 2 cam locks inside the right cart side panel and turn them clockwise to lock the tabletop to the cart.
- Done! — Your BILLY bookcase with foldable table is ready. To fold it away, push the cart into the bookcase: the rear tabletop folds down behind it. Pull the cart out by the tabletop to open it again.
BILLY bookcase with foldable table: questions and answers
How long does it take to assemble the IKEA BILLY bookcase with foldable table?
About 2–3 hours for 2 people, working through the 42 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the BILLY bookcase with foldable table?
Flat & Phillips screwdriver, Allen key (included), drill and wall screws for your wall. Already in the box: Allen key.
Can one person assemble the BILLY bookcase with foldable table?
It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 4 and 5, where the furniture is lifted or turned.
Does the BILLY bookcase with foldable table need to be fixed to the wall?
The manual shows a wall fixing: see step 16 (Wall brackets under the shelf) and step 17 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the BILLY bookcase with foldable table once assembled?
80x33/112x106 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the BILLY bookcase with foldable table?
165 fittings of 15 kinds, the most numerous being 36 × screw, 32 × cam screw, 32 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA BILLY bookcase with foldable table assembly instructions PDF?
The official PDF is manual AA-2568863-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 005.797.55 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2568863-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BILLY bookcase assembly instructions
- IKEA LACK side table assembly instructions
- IKEA LACK coffee table assembly instructions
- IKEA NORDEN gateleg table assembly instructions
- IKEA KVISTBRO storage table assembly instructions
- IKEA LISABO table assembly instructions
- IKEA TÄRNÖ table, outdoor assembly instructions
- IKEA TINGBY side table on castors assembly instructions
All IKEA BILLY assembly guides · All tables assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained