IKEA AGAM junior chair assembly instructions
How to assemble the IKEA AGAM junior chair, step by step: 17 animated steps built from the official manual, about 30 min for 1 person, with Allen key and key handle (included), hammer.
A tall junior chair in black-stained solid wood with a footrest: a spindle backrest, four splayed legs and an H-shaped stretcher, all held with 16 screws. Size: 41×43 cm, 79 cm high, seat height 52 cm. About 30 min, 1 person. Tools: Allen key and key handle (included), Hammer.
Based on the official IKEA manual AA-183046-9 (PDF). Guide updated .
| Steps | 17 |
|---|---|
| Time | 30 min |
| People | 1 |
| Tools | Allen key and key handle (included), Hammer |
| Size | 41×43 cm, 79 cm high, seat height 52 cm |
| Official manual | AA-183046-9 |
| IKEA article number | 702.535.41 (black) |
| Pieces in the box | 28 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Seat | 1 | |
| Backrest with 4 spindles | 1 | |
| Front leg (2 holes) | 2 | |
| Back leg (1 hole) | 2 | |
| Footrest rail | 1 | |
| Side stretcher with centre hole | 2 | |
| Centre rail | 1 | |
| Screw | 106553 | 16 |
| Allen key | 100092 | 1 |
| Key handle | 121030 | 1 |
Steps
- Start the backrest in the seat — Lay the seat flat on a rug, top up. Hold the backrest upright above it and set the ends of the 2 middle spindles in the 2 middle holes at the back of the seat. The 2 outer spindles just rest on the seat for now. Check: Work on a rug or another soft surface so the seat doesn't get scratched.
- Guide the outer spindles in — Squeeze the 2 outer spindles gently inwards until their ends are over the 2 outer holes, and let them slip in.
- Press the backrest down — Push the backrest straight down with both hands on the top rail until all 4 spindles are fully home in the seat.
- Turn the seat over — Turn the seat and backrest over so they rest on the top rail and the front edge of the seat, with the underside facing you. Slide the long arm of Allen key 100092 into the key handle 121030.
- Screw the backrest to the seat — Screw 4 screws 106553 through the underside of the seat into the ends of the 4 spindles. Tighten them firmly with the key in its handle.
- Join the front legs with the footrest — Take the 2 legs with 2 holes (the front legs) and the thinnest rail, the footrest. Push the footrest into the facing holes of the legs, pegs up. Put a screw 106553 through the outside of each leg into the footrest. Leave them loose. Check: Don't tighten the screws yet: they are tightened in step 11.
- Build the H frame — Take the 2 rails with a hole in the middle (side stretchers) and the remaining rail. Push the rail's ends into the middle holes of the side stretchers. Put a screw 106553 through each side stretcher into the rail, and leave them loose.
- Fit the H frame to the front legs — Turn the front legs upside down. Push the front ends of the side stretchers into the lower holes of the front legs, then put a screw 106553 through the front of each leg into the stretcher. Leave them loose.
- Seat on a table, legs on the seat — Turn the seat over and lay it on a table, with the backrest hanging over the edge. Set the pegs of the front legs in the 2 front holes of the seat.
- Fit the first back leg — Take a back leg (1 hole). Set its peg in a back hole of the seat and its hole over the end of the side stretcher. Put a screw 106553 through the back of the leg into the stretcher and leave it loose.
- Fit the second back leg — Fit the other back leg the same way: peg in the last hole of the seat, hole over the end of the other side stretcher. Put a screw 106553 through the back of the leg and leave it loose.
- Tap the legs home and add 4 screws — Tap the frame with a hammer so the legs are fully home in the seat. Then put a screw 106553 into the notch on the inner side of each leg, angled into the seat. Leave them loose too. Check: The notch at the top of each leg must face the middle of the seat.
- Stand the chair up — Turn the chair over, stand it on the floor and press down on the seat so that all the legs sit firmly on the floor.
- Tighten the screws on one side — With the key in its handle, tighten the 4 screws on one side: the front of the front leg, the footrest, the middle of the side stretcher and the back of the back leg.
- Tighten the screws on the other side — Tighten the same 4 screws on the other side of the chair.
- Tighten the 4 screws under the seat — Finally tighten the 4 angled screws at the tops of the legs under the seat. All 12 screws are now tight.
- Done! — Your AGAM junior chair is ready. Check the screws now and then and tighten them again if needed.
AGAM junior chair: questions and answers
How long does it take to assemble the IKEA AGAM junior chair?
About 30 min for 1 person, working through the 17 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the AGAM junior chair?
Allen key and key handle (included), hammer. Already in the box: Allen key and key handle.
Can one person assemble the AGAM junior chair?
Yes, it is a one-person build.
What size is the AGAM junior chair once assembled?
41×43 cm, 79 cm high, seat height 52 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the AGAM junior chair?
17 fittings of 2 kinds, the most numerous being 16 × screw, 1 × key handle. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA AGAM junior chair assembly instructions PDF?
The official PDF is manual AA-183046-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 702.535.41 (black); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-183046-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 106553). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BESTÅ TV bench assembly instructions
All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained