Step by StepAssembly Find your furniture

IKEA BYÅS TV bench assembly instructions

How to assemble the IKEA BYÅS TV bench, step by step: 34 animated steps built from the official manual, about 2–3 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, hammer, wall screw to suit your wall (not included).

IKEA BYÅS TV bench, assembled

A high-gloss white BYÅS TV bench: a cam-lock carcass on a recessed plinth, three compartments with shelves, two push-open drawers on runners, fixed to the wall. Size: 160x42x45 cm. About 2–3 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer, Wall screw to suit your wall (not included).

Based on the official IKEA manual AA-575586-10 (PDF). Guide updated .

BYÅS TV bench: quick facts
Steps34
Time2–3 hours
People2
ToolsFlat-blade screwdriver, Phillips screwdriver, Hammer, Wall screw to suit your wall (not included)
Size160x42x45 cm
Official manualAA-575586-10
IKEA article number802.277.97 (high gloss white)
Pieces in the box146

In the box

PartPart numberQuantity
Top1
Side panel2
Divider2
Bottom panel1
Back rail1
Plinth rail (long)2
Plinth rail (short)2
Shelf3
Drawer front2
Drawer side4
Drawer back2
Drawer bottom2
Cam screw1153124
Cam lock1106304
Plastic nail1105194
Cam screw11833126
Cam lock10343026
Wooden dowel10137512
Screw1003658
Screw11663712
Drawer runner set 113104 (4 rails)2
Wall bracket1069891
Screw1090491
Washer1008232
Grip1234422
Felt pads 108357 (sheet of 4)2
Bumpers 107091 (sheet of 2)4
Shelf support11330112

Steps

  1. Drawer front: cam screws — Start with a drawer (you build two the same way). Lay a drawer front face down on a rug and screw the 2 cam screws 115312 into the small holes near its ends. Check: Use cam screws 115312 here, not 118331. Lay the high-gloss front on something soft.
  2. Dowels and drawer sides — Push a dowel 101375 into the hole next to each cam screw. Stand the 2 drawer sides on the front, grooves facing in, so the dowels and cam screws go into their holes.
  3. Lock the drawer sides — Put a cam lock 110630 into the hole on the inside of each drawer side, next to the front, and turn it clockwise with a flat screwdriver until it grips the cam screw. Check: Use cam locks 110630 here, not 103430.
  4. Slide in the drawer bottom — Tip the drawer up so the front stands upright. Slide the drawer bottom into the grooves in the sides from the open end, all the way to the front.
  5. Drawer back — Lower the drawer back between the sides at the open end, over the drawer bottom. Hammer a plastic nail 110519 through each side into the ends of the back.
  6. Runners on the drawer — Turn the drawer upside down. Lay a runner 113104 on the bottom edge of each side, wheel at the back end, and fix each one with 2 screws 100365. Check: Use screws 100365 here, not 116637.
  7. Grip on the drawer front — Turn the drawer the right way up. Fit the grip 123442 over the middle of the front’s top edge and screw it on from the inside with 2 screws 116637. Check: The drawers have no handle: they open when you push the front (push-open).
  8. The second drawer — Build the second drawer the same way: cam screws and dowels in the front, sides on, cam locks, bottom, back with plastic nails, runners with screws, and the grip.
  9. Plinth frame — Push 2 dowels 101375 into each end of the 2 short plinth rails, 8 in all. Stand the rails on edge on the rug and push the 2 long rails onto the dowels to make a frame.
  10. Cam screws in the bottom panel — Lay the bottom panel next to the frame, top face down. Screw 6 cam screws 118331 into the small holes: 3 along the front edge and 3 along the back edge.
  11. Frame onto the bottom panel — Lift the plinth frame onto the bottom panel so the cam screws go into the holes in the long rails.
  12. Lock the frame — Put 6 cam locks 103430 into the holes on the inside of the long rails and turn each one clockwise until it grips its cam screw.
  13. Felt pads — Press 8 felt pads 108357 onto the bottom edges of the long rails (facing up now): one at each corner and two along the middle of each rail.
  14. Turn it over, cam screws — Turn the base over so it stands on the plinth. Screw 8 cam screws 118331 into the top of the bottom panel: 2 at each end and 2 where each divider goes.
  15. Dividers — Lower the 2 dividers onto the middle cam screws. Turn each so its cam-lock holes face outwards, towards the ends of the bench, and the row of shelf holes runs as shown. Check: Check the hole pattern: the large cam-lock holes are at the bottom and face the drawer compartments.
  16. Lock the dividers — Put 2 cam locks 103430 into the bottom of each divider, on its outer face, and turn each one clockwise to lock it onto the cam screws.
  17. Cam screws in the side panels — Lay the 2 side panels on the rug, inside face up. Screw 2 cam screws 118331 into each, in the small holes along the back edge.
  18. Side panels onto the back rail — Lay the back rail on its back on the rug. Stand each side panel on its back edge and push it onto the end of the rail, so the cam screws go into the holes.
  19. Lock the side panels — Put 4 cam locks 103430 into the back rail, 2 at each end, and turn each one clockwise to lock the side panels.
  20. Frame onto the base — With a helper, stand the side panels and back rail up and lower them onto the base: the side panels over the end cam screws, the back rail behind the dividers. Check: This is a two-person job.
  21. Lock the side panels to the base — Put 2 cam locks 103430 into the bottom of each side panel, on the inside, and turn each one clockwise to lock it onto the base.
  22. Wall bracket — Hold the wall bracket 106989 against the right-hand divider at its top back corner, the bent leg towards the back. Fix it through the slot with a washer 100823 and a screw 109049.
  23. Cam screws in the top — Lay the top face down on the rug. Screw 8 cam screws 118331 into the small holes: 2 at each end and 2 for each divider.
  24. Top on — Turn the top over and lower it onto the side panels and dividers so the cam screws go into the holes. Its ends must be flush with the outer faces of the side panels.
  25. Lock the top — Put 8 cam locks 103430 into the holes just under the top: 2 in each side panel and 2 in each divider. Turn each one clockwise to lock.
  26. Against the wall — Move the bench to where it will stand and push it back against the wall. Check: The bench must be fixed to the wall so it can’t tip over. The wall screw is not included: ask your local shop for one that suits your wall.
  27. Screw it to the wall — Loosen the screw 109049 and slide the bracket back until it touches the wall. Screw a wall screw with a washer 100823 through its hole into the wall, then tighten the screw 109049 again.
  28. Runners in the bench — Fix a runner 113104 low on each side of both drawer compartments, wheel at the front, with 2 screws 116637 each. The runners are marked L and R: L on the left of each opening, R on the right.
  29. Shelf supports — Push 12 shelf supports 113301 into the holes, 4 in each compartment, all at the same height.
  30. Shelves — Put a shelf into each compartment and press it down onto its 4 supports so it locks in place.
  31. First drawer in — Hold the right-hand drawer in front of its opening, tilt the front up a little and set the back wheels on the runners. Slide it in, lower the front and push it home.
  32. Second drawer in — Put the second drawer into the left-hand opening the same way.
  33. Bumpers — Pull both drawers out. Stick 8 bumpers 107091 on the front edges where the drawer fronts close: top and bottom on each side panel and divider. Push the drawers shut; press a front to open it.
  34. Done! — Your BYÅS TV bench is finished and fixed to the wall. Press a drawer front to open it; the shelves sit on their supports in all three compartments.

BYÅS TV bench: questions and answers

How long does it take to assemble the IKEA BYÅS TV bench?

About 2–3 hours for 2 people, working through the 34 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BYÅS TV bench?

Flat-blade screwdriver, Phillips screwdriver, hammer, wall screw to suit your wall (not included).

Can one person assemble the BYÅS TV bench?

It is planned as a 2-person build. One person can do most of it, but get help for steps 4, 11 and 14, where the furniture is lifted or turned.

Does the BYÅS TV bench need to be fixed to the wall?

The manual shows a wall fixing: see step 22 (Wall bracket) and step 27 (Screw it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BYÅS TV bench once assembled?

160x42x45 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the BYÅS TV bench?

114 fittings of 13 kinds, the most numerous being 26 × cam screw, 26 × cam lock, 12 × wooden dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BYÅS TV bench assembly instructions PDF?

The official PDF is manual AA-575586-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 802.277.97 (high gloss white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-575586-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 115312). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained