Step by StepAssembly Find your furniture

IKEA FLISAT doll's house/wall shelf assembly instructions

How to assemble the IKEA FLISAT doll's house/wall shelf, step by step: 22 animated steps built from the official manual, about 45 min for 1 person, with Allen key (included), Phillips screwdriver.

IKEA FLISAT doll's house/wall shelf, assembled

A solid pine doll's house that doubles as a wall shelf: two floors, two partitions, a pitched roof with a chimney, hung on the wall with two screws. Size: 58×22 cm, 59 cm high. About 45 min, 1 person. Tools: Allen key (included), Phillips screwdriver.

Based on the official IKEA manual AA-1635002-7 (PDF). Guide updated .

FLISAT doll's house/wall shelf: quick facts
Steps22
Time45 min
People1
ToolsAllen key (included), Phillips screwdriver
Size58×22 cm, 59 cm high
Official manualAA-1635002-7
IKEA article number502.907.85
Pieces in the box52

In the box

PartPart numberQuantity
Side panel2
Shelf (bottom, middle)2
Partition (lower, upper)2
Back panel (lower, upper)2
Gable1
Roof panel2
Chimney1
Connector screw10029515
Wood screw1095397
Dowel10134513
Dowel1013734
Allen key1000061

Steps

  1. Dowel the upper partition — Lay the middle shelf on its edge. Push a long dowel (101345) into the hole in the end of the upper partition, then fit the partition onto the shelf with the dowel in its hole. Check: Use the long dowels 101345 here, not the short 101373.
  2. Screw the partition on — From the other side of the middle shelf, drive one connector screw (100295) through the shelf into the partition with the Allen key. Turn it by hand, no power drill.
  3. Add the bottom shelf — Stand the lower partition against the middle shelf and put the bottom shelf against it, grooved edge the same way as the middle shelf. Fix it with 2 connector screws (100295) through the bottom shelf.
  4. Dowels in the bottom shelf — Push 2 long dowels (101345) into the holes in the right-hand end of the bottom shelf.
  5. Push the frame together — Press the bottom shelf firmly towards the middle shelf so the partitions sit tight and both shelves line up at the ends.
  6. Fit the right side — Push 2 long dowels (101345) into the end of the middle shelf and 2 into the holes in the right side panel. Then fit the side onto the shelf ends, rounded corner at the bottom front.
  7. Screw the right side — Drive 4 connector screws (100295) through the right side into the ends of the two shelves with the Allen key.
  8. Turn it onto the right side — Carefully tip the frame over so it stands on the right side panel.
  9. Slide in the lower back — Slide the lower back panel down into the grooves of the bottom and middle shelves, all the way to the right side. The smooth side faces into the house.
  10. Slide in the upper back — Push a long dowel (101345) into the hole in the right side, slide the upper back panel down the groove of the middle shelf onto it, then push a second long dowel into its top end.
  11. Fit the left side — Push 4 long dowels (101345) into the ends of the bottom and middle shelves, then put the left side panel on top.
  12. Screw the left side — Drive 5 connector screws (100295) through the left side: 2 into the bottom shelf, 2 into the middle shelf and 1 into the upper back.
  13. Screw the upper back — Turn the house face down. Drive 1 connector screw (100295) through the right side into the upper back panel.
  14. Stand it up — Turn the house over and stand it upright on the bottom edge of the sides.
  15. Short dowels in the tops — Push 3 short dowels (101373) into the top edges of the left side, the upper partition and the right side.
  16. Slide in the gable — Slide the gable down into the groove at the back until it rests on the upper back panel. The long slope goes to the right.
  17. Chimney on the roof — Lay the long roof panel flat, put the chimney on it near the top end and fix it with 2 connector screws (100295) from underneath with the Allen key.
  18. Fit the right roof — Put the long roof panel on the right side, gable and upper partition, over the short dowels. Fix it with 3 wood screws (109539) using a Phillips screwdriver. No power drill.
  19. Dowel at the ridge — Push 1 short dowel (101373) into the hole in the top edge of the right roof panel.
  20. Fit the left roof — Put the short roof panel on the left side and gable, against the dowel at the ridge. Fix it with 4 wood screws (109539) using the Phillips screwdriver.
  21. Fix it to the wall — Hang the house on the wall. Drive 2 screws through the upper back panel into the wall, one in each upper room. Wall screws are not included: choose ones that suit your wall. Check: Screws for the wall are not included. Use a pan-head screw suitable for your wall material.
  22. Done! — Your FLISAT doll's house is ready. Check every screw is tight and the house hangs firmly before children play with it.

FLISAT doll's house/wall shelf: questions and answers

How long does it take to assemble the IKEA FLISAT doll's house/wall shelf?

About 45 min for 1 person, working through the 22 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the FLISAT doll's house/wall shelf?

Allen key (included), Phillips screwdriver. Already in the box: Allen key.

Can one person assemble the FLISAT doll's house/wall shelf?

Yes, it is a one-person build.

Does the FLISAT doll's house/wall shelf need to be fixed to the wall?

The manual shows a wall fixing: see step 21 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the FLISAT doll's house/wall shelf once assembled?

58×22 cm, 59 cm high, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the FLISAT doll's house/wall shelf?

39 fittings of 4 kinds, the most numerous being 15 × connector screw, 13 × dowel, 7 × wood screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA FLISAT doll's house/wall shelf assembly instructions PDF?

The official PDF is manual AA-1635002-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 502.907.85; other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1635002-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example connector screw 100295). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA FLISAT assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained