IKEA INGOLF junior chair assembly instructions
How to assemble the IKEA INGOLF junior chair, step by step: 16 animated steps built from the official manual, about 30 min for 1 person, with Allen key (included), Phillips screwdriver.
A tall junior chair in antique-stained solid wood with a footrest: two glued side frames joined by four rails, a seat, a crossed backrest brace and a curved backrest. Size: 41×45 cm, 77 cm high, seat height 52 cm. About 30 min, 1 person. Tools: Allen key (included), Phillips screwdriver.
Based on the official IKEA manual AA-2025674-5 (PDF). Guide updated .
| Steps | 16 |
|---|---|
| Time | 30 min |
| People | 1 |
| Tools | Allen key (included), Phillips screwdriver |
| Size | 41×45 cm, 77 cm high, seat height 52 cm |
| Official manual | AA-2025674-5 |
| IKEA article number | 603.538.38 (antique stain) |
| Pieces in the box | 32 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side frame (back leg + front leg, glued) | 2 | |
| Seat rail | 2 | |
| Lower rail | 2 | |
| Seat | 1 | |
| X brace bar | 2 | |
| Backrest | 1 | |
| Screw | 100214 | 8 |
| Screw | 100217 | 2 |
| Screw | 109578 | 3 |
| Dowel | 101357 | 2 |
| Dowel | 101350 | 6 |
| Allen key | 100092 | 1 |
Steps
- Stand the lower rails in a side frame — Lay one side frame flat on the floor, legs pointing the same way as shown. Check the round insert at each end of the 2 lower rails is pressed fully in, then stand the rails up in the middle holes of the back leg and the front leg. Check: Work on a soft surface so the wood doesn't get scratched.
- Big dowels in the front seat rail — Take the 2 seat rails. Push a big dowel 101357 into the large hole at each end of one of them: this is the front seat rail. Use only the big dowels here.
- Small dowels in the seat rails — Push the 6 small dowels 101350 in: 1 into the free outer hole at each end of the front seat rail, and 2 into each end of the other seat rail. Leave the middle holes empty: they are for the screws.
- Stand the seat rails up — Push the seat rails, dowels down, into the top holes of the 2 legs: front rail in the front leg, the other in the back leg. The round hole in the side of each rail must show the cross nut inside it. Check: If a rail's side hole shows no nut, turn the rail round.
- Lay on the other side frame — Lower the other side frame onto the 4 rails so the rail ends go into its holes: back leg over the back rails, front leg over the front rails. Press it down evenly.
- Screw the top frame on — Put a screw 100214 through each of the 4 holes in the top side frame into the rails. Turn them in with the Allen key 100092, but leave each head 5 mm proud: they are tightened later. Check: Leave the screw heads 5 mm out for now.
- Stand it up and screw the other side — Lift the chair frame and stand it on its feet. Put 4 more screws 100214 through the holes in the other side frame into the rails, and again leave each head 5 mm proud.
- Lay the seat on — Lay the seat on the frame, rounded edge at the front, and push it back so its back edge sits against the 2 back legs.
- X brace into one back leg — Gently pull the tops of the back legs apart. Hold the 2 crossed bars of the X brace between them and slide their ends into the 2 slots of the right back leg.
- X brace into the other leg — Keep the left back leg pulled out. Line the other ends of the bars up with its 2 slots, then let the leg spring back so the ends go into the slots.
- Tighten the screws on one side — With the Allen key, tighten the 4 screws 100214 on the right side of the chair until their heads are flush with the legs.
- Tighten the other 4 screws — Tighten the 4 screws 100214 on the left side the same way. All 8 screws are now tight.
- Fit the backrest — Ease the backrest between the tops of the back legs so its dowels go into the lower holes. Fix each end with a screw 100217 through the leg, tightened with the Allen key.
- Turn the chair onto a table — Turn the chair upside down onto a table, with the backrest hanging over the edge. Check that the seat sits evenly against the frame all round. Check: Hold the chair as you turn it so the backrest doesn't knock the table edge.
- Screw the seat on — Fix the seat with 3 screws 109578 and a Phillips screwdriver: 1 through the back seat rail and 2 through the front seat rail, into the underside of the seat.
- Done! — Turn the chair back onto its feet. Your INGOLF junior chair is ready. Check the screws now and then and tighten them again if needed.
INGOLF junior chair: questions and answers
How long does it take to assemble the IKEA INGOLF junior chair?
About 30 min for 1 person, working through the 16 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the INGOLF junior chair?
Allen key (included), Phillips screwdriver. Already in the box: Allen key.
Can one person assemble the INGOLF junior chair?
Yes, it is a one-person build.
What size is the INGOLF junior chair once assembled?
41×45 cm, 77 cm high, seat height 52 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the INGOLF junior chair?
21 fittings of 5 kinds, the most numerous being 8 × screw, 6 × dowel, 3 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA INGOLF junior chair assembly instructions PDF?
The official PDF is manual AA-2025674-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 603.538.38 (antique stain); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2025674-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 100214). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BESTÅ TV bench assembly instructions
All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained