Step by StepAssembly Find your furniture

IKEA LISABO chair assembly instructions

How to assemble the IKEA LISABO chair, step by step: 10 animated steps built from the official manual, about 20–30 min for 1 person, with Allen key (included).

Solid ash dining chair: two leg frames that cross under the seat in a half-lap joint, a bent ash-veneer backrest and seat, all fixed with one Allen key. Size: 46×51 cm, 80 cm high, seat height 45 cm (18 1/8×20 1/8", 31 1/2" high). About 20–30 min, 1 person. Tools: Allen key (included).

Based on the official IKEA manual AA-2174482-9 (PDF). Guide updated .

LISABO chair: quick facts
Steps10
Time20–30 min
People1
ToolsAllen key (included)
Size46×51 cm, 80 cm high, seat height 45 cm (18 1/8×20 1/8", 31 1/2" high)
Official manualAA-2174482-9
IKEA article number004.572.35 (ash)
Pieces in the box20

In the box

PartPart numberQuantity
Leg frame (back leg + front leg)2
Block1
Backrest1
Seat1
Bolt1235956
Screw 100211/1002124
Bolt 10087753/100877544
Allen key1000011

Steps

  1. Cross the two leg frames — Stand up the leg frame whose rail has its slot at the top. Lower the other frame onto it from above, slot downwards, so the two slots lock together and the rails cross in an X. Both tall legs must be at the back. Check: Check the inset: the two tall back legs go at the back, side by side. If one tall leg ends up at the front, turn that frame round.
  2. Push in the block and screw the first side — Push the block in from the front between the two rails, small hole on top. Turn 2 screws 100211/100212 through the holes in the rail on this side into the end of the block with the Allen key. Leave the heads a little proud for now. Check: The small hole goes on top. If you see the wide counterbored hole on top, turn the block over.
  3. Screw the other side of the block — Turn 2 more screws 100211/100212 through the other rail into the other end of the block the same way. Again leave the heads a little proud.
  4. Tighten the 4 block screws — Tighten the 4 screws in the rails with the Allen key until the heads sit flush in their holes. Check: The heads must sit flush, not stick out.
  5. Fit the backrest — Hold the backrest between the two tall back legs, curved side to the front, against the inner faces of the legs. From the outside, turn 2 bolts 10087753/10087754 through each leg into the backrest with the Allen key. Leave the heads a little proud. Check: Do not tighten the bolts fully yet: leave a small gap under the heads.
  6. Tighten the backrest bolts — Tighten the 4 backrest bolts with the Allen key until the heads sit flush against the legs. Check: The bolt heads must sit flush against the legs, not stick out.
  7. Turn the chair over onto the seat — Lay the seat on a table, underside up, with its narrow back edge at the table edge. Turn the chair upside down and lower it onto the seat, so the rails rest on the raised pads and the backrest hangs over the table edge.
  8. Bolt the seat on — Push the 6 long bolts 123595 into the holes in the rails and the block and turn them into the seat with the Allen key. Leave the heads a little proud for now. Check: Do not tighten fully yet: first get all 6 bolts started.
  9. Tighten the 6 seat bolts — Tighten all 6 seat bolts with the Allen key until the heads sit flush in their holes. Check: The heads must sit flush in the rails, not stick out.
  10. Done! — Your LISABO chair is ready. Lift it off the table and stand it on its legs. It is tested for 110 kg. Check the bolts now and then and tighten them again if needed.

LISABO chair: questions and answers

How long does it take to assemble the IKEA LISABO chair?

About 20–30 min for 1 person, working through the 10 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the LISABO chair?

Allen key (included). Already in the box: Allen key.

Can one person assemble the LISABO chair?

Yes, it is a one-person build.

What size is the LISABO chair once assembled?

46×51 cm, 80 cm high, seat height 45 cm (18 1/8×20 1/8", 31 1/2" high), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the LISABO chair?

14 fittings of 3 kinds, the most numerous being 6 × bolt, 4 × screw 100211/100212, 4 × bolt 10087753/10087754. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA LISABO chair assembly instructions PDF?

The official PDF is manual AA-2174482-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 004.572.35 (ash); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2174482-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 123595). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA LISABO assembly guides · All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained