Step by StepAssembly Find your furniture

IKEA LUBBAN trolley table with storage assembly instructions

How to assemble the IKEA LUBBAN trolley table with storage (cart), step by step: 11 animated steps built from the official manual, about 20 min for 1 person, with Allen key 100092 (included), spanner 100089 (included).

IKEA LUBBAN trolley table with storage, assembled

A round rattan side table on castors: a deep basket and a shallow tray ring held between two anthracite tube frames, topped with glass. Built lying on its side with screws, cap nuts and the two included tools. Size: Ø50x66 cm. About 20 min, 1 person. Tools: Allen key 100092 (included), Spanner 100089 (included).

Based on the official IKEA manual AA-2587753-3 (PDF). Guide updated .

LUBBAN trolley table with storage: quick facts
Steps11
Time20 min
People1
ToolsAllen key 100092 (included), Spanner 100089 (included)
SizeØ50x66 cm
Official manualAA-2587753-3
IKEA article number504.343.07 (rattan anthracite)
Pieces in the box23

In the box

PartPart numberQuantity
Tube frame with castors2
Rattan basket (bottom)1
Rattan ring with metal cross (top)1
Glass top1
Screw1244354
Washer1008274
Cap nut1048444
Bumper1514104
Allen key1000921
Spanner1000891

Steps

  1. Basket onto the first frame — Lay one frame flat on a soft surface, handle to the left. Stand the deep basket on its edge on the frame, bottom towards the castors. From inside the basket, put a screw (124435) through each of the 2 plates into the legs and turn it in with the allen key (100092). Check: The screw heads must sit flush in the plates, not stick out.
  2. Turn it round, top ring on — Turn the whole thing round. Slide the shallow ring onto the frame from the handle end so its 2 threaded studs go through the holes in the frame tabs. On each stud put a washer (100827) and a cap nut (104844) and turn the nut on by hand. Check: Only hand-tight for now: the nuts are tightened with the spanner once the trolley stands upright.
  3. Second frame on top — Lay the second frame on top, handle at the same end as the first. Its castor end goes over the basket and its 2 tabs slide onto the other 2 studs of the ring. Fit a washer (100827) and a cap nut (104844) on each stud, hand-tight.
  4. Screw the basket to the second frame — Turn it round again. From inside the basket, screw a screw (124435) through each of the 2 plates into the legs of the top frame with the allen key (100092). Check: Check that the screw heads sit flush in the plates.
  5. Stand it upright — Tip the trolley up onto its 4 castors, handles at the top.
  6. Tighten the basket screws (back) — Tighten the 2 screws on the far side of the basket fully with the allen key (100092). Check: The screw heads must end up flush with the metal plates.
  7. Tighten the basket screws (front) — Go round to the other side and tighten the other 2 screws fully in the same way.
  8. Tighten the cap nuts — Under the top ring, tighten all 4 cap nuts with the spanner (100089). Check: Tighten until the washer is pressed flat against the tab.
  9. Bumpers on the ledge — Stick the 4 bumpers (151410) onto the metal ledge inside the top ring, one above each leg, and press them down.
  10. Glass top — Lower the glass top straight down into the top ring so it rests on the 4 bumpers.
  11. Done! — Your LUBBAN trolley table is assembled. The top holds up to 5 kg and the basket up to 10 kg; do not sit on it.

LUBBAN trolley table with storage: questions and answers

How long does it take to assemble the IKEA LUBBAN trolley table with storage?

About 20 min for 1 person, working through the 11 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the LUBBAN trolley table with storage?

Allen key 100092 (included), spanner 100089 (included). Already in the box: Allen key 100092, Spanner 100089.

Can one person assemble the LUBBAN trolley table with storage?

Yes, it is a one-person build.

What size is the LUBBAN trolley table with storage once assembled?

Ø50x66 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the LUBBAN trolley table with storage?

16 fittings of 4 kinds, the most numerous being 4 × screw, 4 × washer, 4 × cap nut. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA LUBBAN trolley table with storage assembly instructions PDF?

The official PDF is manual AA-2587753-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 504.343.07 (rattan anthracite); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2587753-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 124435). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All kitchen & carts assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained