Step by StepAssembly Find your furniture

IKEA ROSENTORP chair assembly instructions

How to assemble the IKEA ROSENTORP chair, step by step: 16 animated steps built from the official manual, about 20–30 min for 1 person, with Allen key (included), Phillips screwdriver, flat-blade screwdriver.

White solid wood dining chair with a crossed backrest: the side rails bolt to the back and front frames with barrel nuts, and the seat screws on with four brackets. Size: 44×53 cm, 91 cm high, seat height 45 cm (17 3/8×20 7/8", 35 7/8" high). About 20–30 min, 1 person. Tools: Allen key (included), Phillips screwdriver, Flat-blade screwdriver.

Based on the official IKEA manual AA-2420961-1 (PDF). Guide updated .

ROSENTORP chair: quick facts
Steps16
Time20–30 min
People1
ToolsAllen key (included), Phillips screwdriver, Flat-blade screwdriver
Size44×53 cm, 91 cm high, seat height 45 cm (17 3/8×20 7/8", 35 7/8" high)
Official manualAA-2420961-1
IKEA article number805.699.98 (white)
Pieces in the box30

In the box

PartPart numberQuantity
Back frame1
Front frame1
Side rail2
Seat1
Bolt1001594
Barrel nut1005054
Screw1095988
Curved washer1159834
Angle bracket1026464
Allen key1116311

Steps

  1. Screw 2 brackets to the back frame — Lay the back frame on its back on a soft surface. Screw 2 angle brackets (102646) onto the back seat rail with 2 screws (109598), round hole flat on the rail and the slotted flange standing up at the seat edge. Check: Work on a rug or the flattened box so the white finish does not get scratched.
  2. Barrel nuts and bolts in the back legs — Push a barrel nut (100505) into the hole on the inside of each back leg, slot facing you. Put a bolt (100159) into the hole on the front of the leg and turn it in by hand a couple of turns, holding the nut straight with a flat screwdriver. Leave the bolts sticking out. Check: Only turn the bolts in by hand for now. They are tightened later.
  3. Push the side rails onto the bolts — Hold each side rail upright, pockets facing in, and push it down over the bolt so the bolt head goes into the pocket and the dowels at the bottom go into the leg.
  4. Washer in and tighten the left back bolt — In the pocket of the left side rail, slide a curved washer (115983) under the bolt head, curved side down into the round end of the pocket. Then tighten the bolt with the Allen key. Check: The curved side of the washer must follow the round end of the pocket. The other way round it will not sit flat.
  5. Washer in and tighten the right back bolt — Do the same in the right side rail: slide the second curved washer (115983) under the bolt head, curved side into the round end, and tighten the bolt with the Allen key.
  6. Screw 2 brackets to the front frame — Lay the front frame on its front beside the chair. Screw the other 2 angle brackets (102646) onto the inside of the front seat rail with 2 screws (109598), slotted flange standing up at the seat edge.
  7. Barrel nuts and bolts in the front legs — Push a barrel nut (100505) into the inside of each front leg, slot facing you. Turn a bolt (100159) into the hole on the top of each leg by hand, a couple of turns, holding the nut straight with the screwdriver. Leave the bolts sticking out.
  8. Put the front frame onto the rails — Turn the front frame over and hold it above the side rails, bolts pointing down. Push it down so the bolt heads go into the pockets of the rails and the dowels into the front legs.
  9. Turn the chair upside down onto a table — Turn the chair upside down and lay it on a table, seat frame on the table top and the backrest hanging over the edge. Check: Put a cloth on the table so the frame does not get scratched.
  10. Washer in and tighten the left front bolt — In the front pocket of the left side rail, slide a curved washer (115983) under the bolt head, curved side into the round end of the pocket, and tighten the bolt with the Allen key. Check: Check the washer: its curved side follows the round end of the pocket.
  11. Washer in and tighten the right front bolt — Do the same in the right side rail: slide the last curved washer (115983) under the bolt head and tighten the bolt with the Allen key.
  12. Stand the chair up, tighten the left bolts — Stand the chair on its legs on the floor and press it square so all 4 legs touch the floor. Then tighten the 2 bolts in the left side rail once more with the Allen key. Check: If the chair rocks, loosen the bolts a little, press it level and tighten them again.
  13. Tighten the right bolts — Tighten the 2 bolts in the right side rail once more with the Allen key, so all 4 bolts are tight.
  14. Turn the chair over onto the seat — Lay the seat top down on a cloth on the table. Turn the chair upside down and lower it onto the seat, backrest over the table edge, so the seat stands out evenly at the sides and front.
  15. Screw the seat on — Turn a screw (109598) through the slot of each of the 4 brackets into the seat with a Phillips screwdriver. Check: Use a hand screwdriver, not a power drill: the screws can strip the seat.
  16. Done! — Your ROSENTORP chair is ready. Lift it off the table and stand it on its legs. It is tested for 110 kg. Check the bolts and screws now and then and tighten them again if needed.

ROSENTORP chair: questions and answers

How long does it take to assemble the IKEA ROSENTORP chair?

About 20–30 min for 1 person, working through the 16 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the ROSENTORP chair?

Allen key (included), Phillips screwdriver, flat-blade screwdriver. Already in the box: Allen key.

Can one person assemble the ROSENTORP chair?

Yes, it is a one-person build.

What size is the ROSENTORP chair once assembled?

44×53 cm, 91 cm high, seat height 45 cm (17 3/8×20 7/8", 35 7/8" high), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the ROSENTORP chair?

24 fittings of 5 kinds, the most numerous being 8 × screw, 4 × bolt, 4 × barrel nut. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA ROSENTORP chair assembly instructions PDF?

The official PDF is manual AA-2420961-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 805.699.98 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2420961-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 100159). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained