IKEA SANDSBERG chair assembly instructions
How to assemble the IKEA SANDSBERG chair, step by step: 13 animated steps built from the official manual, about 15–20 min for 1 person, with Phillips screwdriver, adjustable spanner.
Stackable black dining chair: two steel tube side frames bolted to two curved cross rails, with a perforated plastic backrest and a seat that clicks on. Size: 39×47 cm, 77 cm high, seat height 45 cm (15 3/8×18 1/2", 30 1/4" high). About 15–20 min, 1 person. Tools: Phillips screwdriver, Adjustable spanner.
Based on the official IKEA manual AA-2549283-1 (PDF). Guide updated .
| Steps | 13 |
|---|---|
| Time | 15–20 min |
| People | 1 |
| Tools | Phillips screwdriver, Adjustable spanner |
| Size | 39×47 cm, 77 cm high, seat height 45 cm (15 3/8×18 1/2", 30 1/4" high) |
| Official manual | AA-2549283-1 |
| IKEA article number | 306.054.23 (black) |
| Pieces in the box | 18 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side frame (legs and seat rail) | 2 | |
| Curved cross rail | 2 | |
| Backrest | 1 | |
| Seat | 1 | |
| Seat-hook cap | 128671 | 2 |
| Bolt | 128654 | 4 |
| Screw | 106917 | 2 |
| Nut | 104875 | 4 |
Steps
- Lay out the frames, fit the first cross rail — Lay both side frames flat on a rug, short pegs pointing up. Push one curved cross rail straight down onto the peg at the front corner of the first frame, with the hex hole at its end facing the top of the chair. Check: Check the curve of the rail: it must bow the way shown in the manual, not the other way round.
- Fit the second cross rail — Push the second cross rail straight down onto the peg at the back post of the same frame, curved the same way and with its hex hole facing the top of the chair.
- Bolt the rails to the first frame — Push a bolt 128654 into the hex hole at the end of each rail, through the rail and the peg. The hex head sits in the hex hole.
- Flip the second frame onto the rails — Turn the second side frame over so its pegs point down, and lower it onto the free ends of the two rails: front corner peg into the front rail, back post peg into the back rail.
- Bolt the rails to the second frame — Push the other 2 bolts 128654 into the hex holes at the rail ends on the second frame, through the rails and the pegs.
- Put the 4 nuts on by hand — On the other side of each rail end, turn a nut 104875 onto the end of each bolt, flange towards the rail. Hand-tight only for now. Check: You tighten the nuts with a spanner in step 9.
- Stand the chair up, fit the backrest — Stand the frame up on its four legs. Press the backrest straight down over the tops of the two back posts until it stops.
- Screw the backrest to the posts — From behind, drive a screw 106917 through the bottom of each backrest sleeve into the post with a Phillips screwdriver.
- Tighten the 4 nuts — Turn the chair round to face you. Tighten the 4 nuts under the rail ends firmly with an adjustable spanner, crosswise in the manual's order: 1 front left, 2 back right, 3 back left, 4 front right (left and right as you sit on the chair). Check: Tightening crosswise keeps the frame square and the chair level.
- Push the caps onto the back nuts — Push a cap 128671 up over each of the two back nuts, under the back cross rail, slot towards the back of the chair.
- Hook the seat on at the back — Hold the seat with its front raised and lower its back edge between the back posts, so the 2 hooks under the back go down into the slots of the caps.
- Click the seat down — Press the front of the seat down until all 6 clips under it snap over the rails with a click.
- Done! — Your SANDSBERG chair is ready. It is tested for 110 kg. Check the nuts now and then: lift off the two back caps, tighten all 4 nuts with the spanner and push the caps back on.
SANDSBERG chair: questions and answers
How long does it take to assemble the IKEA SANDSBERG chair?
About 15–20 min for 1 person, working through the 13 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the SANDSBERG chair?
Phillips screwdriver, adjustable spanner.
Can one person assemble the SANDSBERG chair?
Yes, it is a one-person build.
What size is the SANDSBERG chair once assembled?
39×47 cm, 77 cm high, seat height 45 cm (15 3/8×18 1/2", 30 1/4" high), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the SANDSBERG chair?
12 fittings of 4 kinds, the most numerous being 4 × bolt, 4 × nut, 2 × seat-hook cap. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA SANDSBERG chair assembly instructions PDF?
The official PDF is manual AA-2549283-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 306.054.23 (black); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2549283-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example seat-hook cap 128671). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BESTÅ TV bench assembly instructions
All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained