IKEA TEODORES chair assembly instructions
How to assemble the IKEA TEODORES chair, step by step: 16 animated steps built from the official manual, about 20–30 min for 1 person, with Phillips screwdriver, Allen keys (included), scissors.
Stackable dining chair: two powder-coated steel side frames joined by three cross rails, with a moulded plastic backrest and seat. Size: 46×54 cm, 80 cm high, seat height 45 cm (18 1/8×21 1/4", 31 1/2" high). About 20–30 min, 1 person. Tools: Phillips screwdriver, Allen keys (included), Scissors.
Based on the official IKEA manual AA-2024077-17 (PDF). Guide updated .
| Steps | 16 |
|---|---|
| Time | 20–30 min |
| People | 1 |
| Tools | Phillips screwdriver, Allen keys (included), Scissors |
| Size | 46×54 cm, 80 cm high, seat height 45 cm (18 1/8×21 1/4", 31 1/2" high) |
| Official manual | AA-2024077-17 |
| IKEA article number | 905.306.27 (blue) |
| Pieces in the box | 33 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Front leg tube (bent) | 2 | |
| Back leg / backrest post tube | 2 | |
| Plastic insert (square and round mark) | 2 | |
| Backrest | 1 | |
| Back cross rail (curved) | 1 | |
| Cross rail (straight) | 2 | |
| Seat | 1 | |
| Bolt | 100104 | 6 |
| Stud screw | 10117292 | 4 |
| Screw | 121760 | 4 |
| Screw | 109544 | 2 |
| Spacer | 10051998 | 4 |
| Allen key | 108490 | 1 |
| Allen key | 100001 | 1 |
Steps
- Click the inserts onto the bent tubes — Cut the two plastic inserts apart with scissors. Lay both bent tubes flat on a soft surface and press an insert onto the short end of each until it clicks: the square-marked insert on one tube, the round-marked one on the other. Check: Each insert fits one way only: the marks face up and the holes line up with the holes in the tube.
- Join the tubes of the first side frame — Stand the bent tube with the square-marked insert up and put a straight tube against its outside, alongside the short end. From the inside, screw 2 stud screws 10117292 through the insert into the straight tube with Allen key 108490, until they sit flush. Check: Tighten the studs fully: the head must sit level with the insert, not stick out.
- Join the tubes of the second side frame — Build the second side frame the same way, with the round-marked insert: straight tube on the outside, 2 stud screws 10117292 from the inside, tightened flush with Allen key 108490. Stand it next to the first frame.
- Push the backrest onto the first post — Hold the backrest above the first side frame, curved side to the front, and push its pocket down over the top of the straight tube until the post is fully inside.
- Fit the second side frame — Hold the first frame with the backrest up, stand the second side frame under the free side of the backrest and push its post up into the other pocket. Both frames then stand level on the floor. Check: The two posts must go all the way into the backrest pockets.
- Fit the curved back cross rail — Push the curved cross rail up between the back ends of the seat rails, curving backwards. Turn a bolt 100104 into each end from the outside by hand, leaving a small gap under the head. Check: Do not tighten the bolts yet: all 6 are tightened together once the three cross rails are in.
- Fit the middle cross rail — Push a straight cross rail up between the seat rails at the middle holes. Turn a bolt 100104 into each end from the outside by hand, again leaving a small gap.
- Fit the front cross rail — Push the second straight cross rail up between the seat rails at the front holes, just behind the front legs. Turn a bolt 100104 into each end by hand, leaving a small gap.
- Screw the backrest to the posts — Reach in under the backrest and drive a screw 109544 through the inner wall of each pocket into the post, with a Phillips screwdriver. Check: Use a hand screwdriver, not a drill. These are the flat-headed screws 109544, not 121760.
- Tighten the bolts on the first side — Tighten the 3 bolts 100104 on the first side frame firmly with Allen key 100001.
- Tighten the bolts on the other side — Tighten the 3 bolts on the other side frame the same way. Stand the chair on a flat floor: all four legs must touch it. If it rocks, loosen the bolts, press the chair down and tighten them again. Check: The chair must stand level on all four legs before you fit the seat.
- Hook the seat onto the front rail — Hold the seat with its back edge raised and slide it in from the front, so the two hooks under its front edge catch under the front cross rail.
- Press the seat down — Hold the backrest and press the back of the seat down until it clicks: the 4 pegs under the seat go into the holes in the seat rails.
- Turn the chair over onto a table — Turn the chair upside down and lay the seat on a table, with the backrest hanging over the edge.
- Screw the seat on from below — Press a spacer 10051998 into each of the 4 holes under the seat rails. Drive a screw 121760 through each spacer into the seat with a Phillips screwdriver. Check: Use a hand screwdriver, not a drill, so the screws do not strip the plastic. These are the round-headed screws 121760.
- Done! — Your TEODORES chair is ready. Turn it back onto its legs. It is tested for 110 kg. Check the bolts now and then and tighten them again if needed.
TEODORES chair: questions and answers
How long does it take to assemble the IKEA TEODORES chair?
About 20–30 min for 1 person, working through the 16 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TEODORES chair?
Phillips screwdriver, Allen keys (included), scissors. Already in the box: Allen keys.
Can one person assemble the TEODORES chair?
Yes, it is a one-person build.
What size is the TEODORES chair once assembled?
46×54 cm, 80 cm high, seat height 45 cm (18 1/8×21 1/4", 31 1/2" high), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the TEODORES chair?
20 fittings of 5 kinds, the most numerous being 6 × bolt, 4 × stud screw, 4 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TEODORES chair assembly instructions PDF?
The official PDF is manual AA-2024077-17, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 905.306.27 (blue); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2024077-17. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 100104). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BESTÅ TV bench assembly instructions
All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained