IKEA TJUSIG bench with shoe storage assembly instructions
How to assemble the IKEA TJUSIG bench with shoe storage, step by step: 16 animated steps built from the official manual, about 30–45 min for 1 person, with flat-blade screwdriver, Allen key (included).
White hallway bench with two shoe shelves of steel rods: two ready-made end frames joined by wooden rails, rods and bolts, built standing on end, with the seat screwed on last. Size: 108x34x50 cm. About 30–45 min, 1 person. Tools: Flat-blade screwdriver, Allen key (included).
Based on the official IKEA manual AA-354147-1 (PDF). Guide updated .
| Steps | 16 |
|---|---|
| Time | 30–45 min |
| People | 1 |
| Tools | Flat-blade screwdriver, Allen key (included) |
| Size | 108x34x50 cm |
| Official manual | AA-354147-1 |
| IKEA article number | 701.527.02 (white) |
| Pieces in the box | 43 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| End frame | 2 | |
| Lower rail | 2 | |
| Top rail | 1 | |
| Rod with threaded ends | 2 | |
| Plain rod | 6 | |
| Seat | 1 | |
| Cardboard spacer | 1 | |
| Long bolt | 100263 | 4 |
| Screw | 100214 | 7 |
| Bolt | 100102 | 4 |
| Dowel | 101350 | 8 |
| Cross dowel | 100505 | 4 |
| Allen key | 100001 | 1 |
Steps
- Lower rails onto the first end frame — Stand one end frame on its edge on a soft surface, as drawn. Push a dowel (101350) into the dowel hole in one end of each lower rail, then push both rails onto the frame, in line with its legs, at the end with the free leg ends. Check: Each lower rail has a small round hole near both ends on one face: turn both rails so these holes face the same way, towards the leg ends, as drawn.
- Bolt the rails to the frame — Push a cross dowel (100505) into the hole near the end of each rail and turn its slot with a flat screwdriver so the threaded hole lines up with the bolt hole. Push a long bolt (100263) through each leg into the rail and screw it into the cross dowel with the allen key (100001).
- Turn it up, then the top rail — Turn the frame over so it lies flat with the rails standing up. Push 2 dowels (101350) into each end of the top rail (4 in all) and stand it on the dowel holes in the top crosspiece, at the opposite end of the frame from the lower rails. Check: The top rail has 3 screw holes along one face: turn that face the same way as the cross-dowel holes in the lower rails (towards the leg ends).
- Rods with threaded ends into the legs — Find the 2 rods with a thread inside their ends. Push them down into the holes in the inside of the 2 legs, at the middle crosspiece. Check: Use only the 2 threaded rods here: the bolts screw into them later. The other 6 rods are plain.
- Six plain rods into the crosspieces — Push the 6 plain rods down into the holes in the 2 lower crosspieces of the frame: 3 into the middle crosspiece and 3 into the one by the lower rails.
- Press out the spacer corners — Take the cardboard spacer and press out the 2 small perforated corner pieces, so it can fit around the lower rails.
- Spacer over the rods — Press the cardboard spacer down over the tops of all 8 rods, each rod through its own hole, until it sits a little below the rod ends. It holds the rods in line for the next step.
- Second end frame on top — Push a dowel (101350) into the top end of each lower rail. Lower the second end frame onto the rods, rails and dowels, inside face down, with its leg ends on the same side as the first frame.
- Bolt the second frame to the rails — Push a cross dowel (100505) into the hole near the top of each lower rail and line up its slot with the flat screwdriver. Push a long bolt (100263) down through each leg of the top frame into the rail and screw it into the cross dowel.
- Bolt the threaded rods (top frame) — Screw a bolt (100102) through each leg of the top frame into the end of the threaded rod below it and tighten it with the allen key (100001).
- Remove the cardboard spacer — The frames now hold the rods in place. Tear the cardboard spacer out from between the rods and throw it away.
- Lay it down, bolt the first frame — Lay the bench down on its side again. Screw the last 2 bolts (100102) through the legs of the first end frame into the other ends of the threaded rods and tighten them with the allen key.
- Upside down onto the seat — Lay the seat face down on a soft surface, such as a rug. Turn the bench upside down and lower it onto the seat, centred, so the seat sticks out a little all round.
- Screw on the seat — Drive 7 screws (100214) into the seat with the allen key (100001): 2 through the top crosspiece of each end frame and 3 through the top rail.
- Turn it the right way up — Turn the bench over onto its legs.
- Done! — Your TJUSIG bench is assembled: sit on the top and keep shoes on the two rod shelves.
TJUSIG bench with shoe storage: questions and answers
How long does it take to assemble the IKEA TJUSIG bench with shoe storage?
About 30–45 min for 1 person, working through the 16 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TJUSIG bench with shoe storage?
Flat-blade screwdriver, Allen key (included). Already in the box: Allen key.
Can one person assemble the TJUSIG bench with shoe storage?
Yes, it is a one-person build.
What size is the TJUSIG bench with shoe storage once assembled?
108x34x50 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the TJUSIG bench with shoe storage?
27 fittings of 5 kinds, the most numerous being 8 × dowel, 7 × screw, 4 × long bolt. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TJUSIG bench with shoe storage assembly instructions PDF?
The official PDF is manual AA-354147-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 701.527.02 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-354147-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example long bolt 100263). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TJUSIG shoe rack assembly instructions
- IKEA MARIUS stool assembly instructions
- IKEA BEKVÄM step stool assembly instructions
- IKEA LÄTT children's table with 2 chairs assembly instructions
- IKEA STIG bar stool with backrest assembly instructions
- IKEA FRANKLIN bar stool with backrest, foldable assembly instructions
- IKEA MAMMUT children's stool assembly instructions
- IKEA BRIMNES TV bench assembly instructions
All IKEA TJUSIG assembly guides · All chairs & stools assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained