Step by StepAssembly Find your furniture

IKEA KOLBJÖRN cabinet in/outdoor assembly instructions

How to assemble the IKEA KOLBJÖRN cabinet in/outdoor, step by step: 25 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Allen key (included), Phillips screwdriver, flat-blade screwdriver, spirit level, wall screws and plugs (not included).

IKEA KOLBJÖRN cabinet in/outdoor, assembled

A beige powder-coated steel cabinet for indoors or outdoors: two side frames and a bottom panel bolted together lying down, a back and a top that hook on, two doors on pivot pins and a shelf on hooks. Size: 80×35×81 cm (31 1/2×13 3/4×31 7/8"). About 1–1.5 hours, 1 person. Tools: Allen key (included), Phillips screwdriver, Flat-blade screwdriver, Spirit level, Wall screws and plugs (not included).

Based on the official IKEA manual AA-2136123-13 (PDF). Guide updated .

KOLBJÖRN cabinet in/outdoor: quick facts
Steps25
Time1–1.5 hours
People1
ToolsAllen key (included), Phillips screwdriver, Flat-blade screwdriver, Spirit level, Wall screws and plugs (not included)
Size80×35×81 cm (31 1/2×13 3/4×31 7/8")
Official manualAA-2136123-13
IKEA article number304.092.95 (beige)
Pieces in the box61

In the box

PartPart numberQuantity
Back leg (channel)2
Front leg2
Side panel2
Bottom panel1
Back panel1
Top panel1
Shelf half2
Door2
Foot100057574
Hex bolt1000571616
Screw1308642
Screw1442623
Screw1900181
Bushing1426614
Cap100056904
Hook100058354
Wall spacer1146642
Rubber bumper100043502
Door pivot100908804
Allen key1000921
Door stop plate100061561

Steps

  1. Screw on the feet — Lay out the 4 legs: 2 back legs (open channels with slots) and 2 front legs. Screw a foot (10005757) clockwise into the bottom end of each leg by hand.
  2. Build the two side frames — For each side: lay a side panel into the slots of a back leg and press it down. Push a front leg onto the other edge of the panel. Then bend the 4 tabs along the back leg over with your fingers so the panel is locked. Check: The feet of both legs must be at the same end.
  3. Stand up a side frame, push in the bottom — Stand one side frame on its back leg, inner side facing the middle. Push the bottom panel onto it at the end with the feet, so its corners slide into place between the legs. Check: The flanges of the bottom panel point towards the feet.
  4. Push on the second side frame — Stand the second side frame up the same way and push it onto the free end of the bottom panel.
  5. Bolt the bottom in, stand it up — Screw in 6 bolts (10005716) with the Allen key: one through the front of each front leg and one through the outer side of every leg, into the bottom panel. Then tip the frame up onto its feet. Check: Tighten the bolts firmly, but not so hard that the powder coating cracks.
  6. Two more bolts at the front — With the frame standing, screw a bolt (10005716) through the lower hole in the front of each front leg, into the bottom panel.
  7. Join the two shelf halves — Lay the two shelf halves upside down, end to end, so the holes in their middle flanges line up. Join them with 3 screws (144262) from inside the near half.
  8. Hook in the back panel — From above, lower the back panel between the back legs, push its hooks into the slots of the legs and slide it all the way down. Bend the 2 tabs at the edge over to lock it.
  9. Bend the bottom tabs down — Inside the cabinet, bend the 8 tabs in the bottom panel down flat into their recesses: 4 along the back panel and 2 at each side.
  10. Put on the top panel — Lower the top panel onto the frame, skirts over the leg tops, and press it down all round until it sits flat.
  11. Bend the top tabs up — From inside, push the 8 tabs under the top panel up flat into their recesses: 4 along the back and 2 at each side.
  12. Bolt the top to the legs — Screw 2 bolts (10005716) into each leg top with the Allen key: one through the side skirt of the top panel and one through the front or back skirt. 8 bolts in all.
  13. Bushings for the door pivots — Press a bushing (142661) into the hole at each front corner: up into the flange under the top panel, and down into the bottom panel.
  14. Put the doors in — Hold each door open and set it into the opening, hinge edge against the front leg, so the holes at its top and bottom corners line up with the bushings. Check: The door with the padlock handle goes on the right.
  15. Clip in the door pivots — At each hinge corner, push a door pivot (10090880) into the door from inside until it clicks, so its pin goes into the bushing. Top and bottom on both doors.
  16. Stop plate on the left door — Inside the left door, at the bottom of its free edge, screw on the stop plate (10006156) with the screw (190018), the bent tongue sticking out past the edge. Check: The plate stops the right door when it closes over the left one.
  17. Bumpers on the right door — Inside the right door, near its free edge at the top and the bottom, screw a screw (130864) through a rubber bumper (10004350) into the small hole.
  18. Hang the shelf hooks — Hook the 4 hooks (10005835) into the slots at the height you want the shelf: front and back on both sides, all at the same height.
  19. Lay in the shelf — Turn the shelf the right way up. Tilt it to pass between the front legs, then lower it flat onto the 4 hooks.
  20. Wall spacers behind the fixing holes — Measure the gap between the back panel and the wall, snap a wall spacer (114664) to that thickness (6, 12 or 18 mm) and put one behind each fixing hole near the top of the back panel.
  21. Against the wall, level it — Close the doors. Push the cabinet back against the wall, check the top with a spirit level and turn the feet in or out until it is level.
  22. Fix it to the wall — Open the doors. From inside, screw a wall screw through each hole near the top of the back panel and through the spacer behind it into the wall. Check: Fix the cabinet to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall.
  23. Caps on top — Close the doors and press a cap (10005690) into each of the 4 holes on top, above the legs.
  24. Stacking with KOLBJÖRN (optional) — Only when you stack this cabinet with another KOLBJÖRN unit: leave the caps off where the units meet. The upper unit's feet go through the holes in the lower unit's top and are screwed into its legs from inside with a flat-blade screwdriver. Check: Nothing to do for a cabinet that stands on its own.
  25. Done! — Your KOLBJÖRN cabinet is assembled and fixed to the wall. Max load on the shelf: 30 kg. The right door has a loop for a padlock.

KOLBJÖRN cabinet in/outdoor: questions and answers

How long does it take to assemble the IKEA KOLBJÖRN cabinet in/outdoor?

About 1–1.5 hours for 1 person, working through the 25 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the KOLBJÖRN cabinet in/outdoor?

Allen key (included), Phillips screwdriver, flat-blade screwdriver, spirit level, wall screws and plugs (not included). Already in the box: Allen key.

Can one person assemble the KOLBJÖRN cabinet in/outdoor?

Yes, it is a one-person build.

Does the KOLBJÖRN cabinet in/outdoor need to be fixed to the wall?

The manual shows a wall fixing: see step 20 (Wall spacers behind the fixing holes) and step 22 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the KOLBJÖRN cabinet in/outdoor once assembled?

80×35×81 cm (31 1/2×13 3/4×31 7/8"), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the KOLBJÖRN cabinet in/outdoor?

47 fittings of 12 kinds, the most numerous being 16 × hex bolt, 4 × foot, 4 × bushing. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA KOLBJÖRN cabinet in/outdoor assembly instructions PDF?

The official PDF is manual AA-2136123-13, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 304.092.95 (beige); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2136123-13. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example foot 10005757). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained