IKEA LIXHULT cabinet assembly instructions
How to assemble the IKEA LIXHULT cabinet, step by step: 18 animated steps built from the official manual, about 30–45 minutes for 1 person, with flat-blade screwdriver, Phillips screwdriver, hammer (only without legs), wall screws and plugs (not included).
A small grey powder-coated steel cabinet with two doors: two base frames, panels that click and hook together, four legs and doors on pivot pins. Size: 60×35×57 cm (23 5/8×13 3/4×22 1/2"). About 30–45 minutes, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer (only without legs), Wall screws and plugs (not included).
Based on the official IKEA manual AA-1826474-8 (PDF). Guide updated .
| Steps | 18 |
|---|---|
| Time | 30–45 minutes |
| People | 1 |
| Tools | Flat-blade screwdriver, Phillips screwdriver, Hammer (only without legs), Wall screws and plugs (not included) |
| Size | 60×35×57 cm (23 5/8×13 3/4×22 1/2") |
| Official manual | AA-1826474-8 |
| IKEA article number | 703.286.69 (metal grey) |
| Pieces in the box | 35 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Base frame | 2 | |
| Side panel | 2 | |
| Back panel | 1 | |
| Bottom panel | 1 | |
| Top panel | 1 | |
| Leg | 4 | |
| Door | 2 | |
| Top hinge | 10047138 | 2 |
| Screw | 106917 | 8 |
| Plug | 115447 | 4 |
| Pivot pin | 151059 | 2 |
| Connector | 151060 | 2 |
| Glide | 151061 | 4 |
Steps
- Lay out the two base frames — Lay the two base frames on a rug, posts up, the long rails parallel. The back frame has 2 holes in each post: they face in. The front frame has a hole on top of its rail near each end: those face up. Check: Check the holes before you go on: a frame turned the wrong way cannot be fixed later.
- Click on the side panels — Hold a side panel over the left posts, the folded edges towards the middle, and push it down until the channels at its corners click over both posts. Do the same with the other side panel on the right.
- Hook in the back panel — Hold the back panel over the back of the cabinet, right end raised. Slide it left until its left edge is over the channel at the back of the left side panel, swing the right end down over the right channel, then slide the panel down into both channels.
- Lock the back panel at the top — At both top back corners, put a flat-blade screwdriver behind the small tab on the back panel and bend it outwards over the top edge of the side panel. That locks the back panel in place.
- Put in the bottom panel — Hold the bottom panel with its back edge raised and hook the bent lip along its front edge over the front rail. Then press the back down until the panel lies flat on both rails.
- Lay it on its back, lock the bottom — Tip the cabinet back so it lies on its back panel, bottom towards you. Under the bottom panel, near the back, bend the tab at each side outwards with a flat-blade screwdriver.
- Push in the legs — Push a leg, narrow end first, into the open end of each of the 4 corner posts as far as it goes. Then stand the cabinet up on its legs. Without legs: tap a glide (151061) into each post with a hammer instead. Check: The legs are optional: with them the cabinet is 57 cm high, without them 35 cm.
- Screw the back legs in place — From inside the cabinet, drive a screw (106917) through the hole in the inner face of each back corner post, into the leg. Without legs: press a plug (115447) into each hole instead.
- Screw the front legs in place — Do the same at the two front corner posts: a screw (106917) from inside through each post into the leg. Without legs: a plug (115447) in each hole.
- Put on the top panel — Turn the top panel over so the two hinge holes underneath are at the front. Lower it onto the cabinet so the 4 tabs on the side panels go into its slots, then push it back until it stops.
- Lock the top panel — Under the front edge of the top panel, next to each hinge hole, bend the small tab down with a flat-blade screwdriver. The top panel is now locked.
- Stand it against the wall — Put the cabinet where it will stand and push it back against the wall.
- Fix it to the wall — From inside, drive a wall screw through each of the 2 holes near the top of the back panel into the wall. Check: Fix the cabinet to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall. Use screws with a flat-bottomed head, not countersunk.
- Pivot pins for the doors — Press a pivot pin (151059) into the hole at each front corner of the bottom, pin end up.
- Set the doors on the pins — Hold a door open at a right angle and set the hole in its bottom hinge corner over the pivot pin. Hang the left door first, then the right one.
- Click in the top hinges — In the top hinge corner of each door, push a top hinge (10047138) up into the door until it clicks and its pin goes into the hole in the top panel.
- Close the doors — Close both doors and check that they turn freely and meet evenly in the middle.
- Done! — Your LIXHULT cabinet is assembled and fixed to the wall. Max load on the top: 5 kg. To join two LIXHULT cabinets side by side or stacked, screw a connector (151060) across the joint at the back with 2 screws (106917): the box includes 2 connectors and 4 screws for this.
LIXHULT cabinet: questions and answers
How long does it take to assemble the IKEA LIXHULT cabinet?
About 30–45 minutes for 1 person, working through the 18 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the LIXHULT cabinet?
Flat-blade screwdriver, Phillips screwdriver, hammer (only without legs), wall screws and plugs (not included).
Can one person assemble the LIXHULT cabinet?
Yes, it is a one-person build.
Does the LIXHULT cabinet need to be fixed to the wall?
The manual shows a wall fixing: see step 13 (Fix it to the wall) and step 18 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the LIXHULT cabinet once assembled?
60×35×57 cm (23 5/8×13 3/4×22 1/2"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the LIXHULT cabinet?
22 fittings of 6 kinds, the most numerous being 8 × screw, 4 × plug, 4 × glide. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA LIXHULT cabinet assembly instructions PDF?
The official PDF is manual AA-1826474-8, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 703.286.69 (metal grey); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1826474-8. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example top hinge 10047138). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
- IKEA EKET cabinet assembly instructions
- IKEA BRIMNES bookcase assembly instructions
All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained