IKEA METOD wall cabinet frame assembly instructions
How to assemble the IKEA METOD wall cabinet frame, step by step: 26 animated steps built from the official manual, about 30–45 min for 1 person, with Phillips screwdriver, flat screwdriver, hammer, clamps (only to join cabinets).
The white METOD kitchen wall cabinet carcass: cam-lock frame built lying on its side, slide-in back panel nailed square, then hung on a suspension rail or straight on the wall. Doors are sold separately. Size: 60x37x80 cm. About 30–45 min, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Hammer, Clamps (only to join cabinets).
Based on the official IKEA manual AA-2238433-6 (PDF). Guide updated .
| Steps | 26 |
|---|---|
| Time | 30–45 min |
| People | 1 |
| Tools | Phillips screwdriver, Flat screwdriver, Hammer, Clamps (only to join cabinets) |
| Size | 60x37x80 cm |
| Official manual | AA-2238433-6 |
| IKEA article number | 302.055.28 (white) |
| Pieces in the box | 52 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top panel | 1 | |
| Bottom panel | 1 | |
| Back panel | 1 | |
| Cam screw | 118331 | 8 |
| Cam lock | 113434 | 8 |
| Dowel | 101351 | 8 |
| Suspension fitting | 10049278 | 2 |
| Screw | 10046940 | 6 |
| Bag of nails | 319503 | 1 |
| Spacer 10036383/10039201 | 2 | |
| Lock 124526 (rail) | 2 | |
| Cover 124518/124519 | 2 | |
| Insert 10039571 (no rail) | 2 | |
| Keyhole plate 103693 (no rail) | 2 | |
| Screw 10035574 (joining cabinets) | 4 |
Steps
- Cam screws into the side panels — Lay both side panels on a soft surface, inner faces (with the rows of holes) up and the back-panel grooves facing outwards. Screw 4 cam screws 118331 into the small holes at the ends of each panel.
- Suspension fittings — Screw a suspension fitting 10049278 into the corner of each side panel at the grooved edge, next to the top end (where the pre-drilled holes are), with 3 screws 10046940. The upright plate goes along the grooved edge.
- Top and bottom panels on one side — Push 2 dowels 101351 into one end of the top panel and 2 into the bottom panel. Stand both on the side panel whose back groove faces away from you: the top panel at the end with the fitting, grooves at the back. Press the dowels into the holes.
- Cam locks: bottom panel — Push 2 cam locks 113434 into the holes in the outside of the bottom panel, next to the side panel on the floor. Turn each clockwise with a flat screwdriver until it grips the cam screw.
- Cam locks: top panel — Do the same on the outside of the top panel: 2 cam locks 113434, each turned clockwise with the flat screwdriver until it locks.
- Slide in the back panel — Slide the back panel down into the grooves of the top and bottom panels, notched corners at the top-panel end, until it sits in the groove of the side panel underneath.
- Second side panel — Push 4 dowels 101351 into the free ends of the top and bottom panels. Turn the second side panel over onto them, cam screws and fitting facing down and its fitting at the top-panel end, and press it into place.
- Cam locks: bottom panel, top end — Push 2 cam locks 113434 into the outside of the bottom panel next to the side panel you just fitted, and turn them clockwise to lock.
- Cam locks: top panel, top end — Lock the top panel the same way: 2 cam locks 113434 in its outside face, turned clockwise with the flat screwdriver.
- Square it up, first nail — Tip the frame forward onto its front edges, back panel up. Make sure all corners are at 90°, then hammer a nail 319503 straight down through the back panel into the edge of the side panel nearest you, low down near the bottom panel. Check: Hammer straight, not at an angle, or the nail can come out through the side of the panel.
- Second nail — Keep the corners square: push the back panel against the bottom panel and hammer a nail into the bottom panel edge, close to the far side panel.
- Third nail — Push the back panel towards the near side panel and hammer a nail into its edge near the top, just below the suspension fitting.
- Spacers at the bottom corners — Place a spacer 10036383 on the back panel at each bottom corner, over the bottom panel edge, and nail it on with a nail 319503. The spacers keep the bottom of the cabinet the same distance from the wall as the hooks.
- Nail the back all round — Hammer in the remaining nails 319503 all round: 5 more along each side panel edge, 1 in the middle of the bottom edge and 1 in the middle of the top edge. Check: The manual labels this step 10x but its drawing shows 12 nail positions; the animation follows the drawing.
- Rail: hang it on the suspension rail — With a METOD suspension rail (sold separately, fixed to the wall as its own manual shows): stand the cabinet up, lift it, and hook both suspension fittings over the rail. Check: Hanging it straight on the wall instead? Follow the "No rail" steps after the rail steps.
- Rail: lock the fittings — Check that both hooks sit fully over the rail. Push a lock 124526 into the round hole of each suspension fitting and turn it clockwise with a flat screwdriver until it locks.
- Info: joining two cabinets — Only when two cabinets hang side by side: clamp their front edges flush, then screw 4 screws 10035574 through the pre-drilled holes in the side panel into the next cabinet, 2 near the top and 2 near the bottom.
- Rail: covers on — Push a cover 124518 over each suspension fitting, towards the side panel, until it clicks into place.
- No rail: start from the bare frame — Hanging the cabinet straight on the wall instead of on a rail? Start again from the frame as it was after step 12: no rail, no locks 124526 and no covers yet. Stand it with its back towards you.
- No rail: inserts in the fittings — Slide an insert 10039571 onto each suspension fitting from behind, towards the side panel, so its round hole lines up with the hole in the fitting. Check: Fit the insert the right way round, as the small drawing in the manual shows.
- No rail: mark the wall, set it aside — Hold the cabinet up against the wall where it will hang and mark the middle of each fitting's round hole on the wall. Then set the cabinet aside.
- No rail: screws in the wall — Drive a pan-head wall screw into each mark, leaving the head about 1.5 cm out. Nothing is in front of the wall now, so you can see what you are doing. Check: Wall screws and plugs are not included: use ones that suit your wall (fix into studs in a stud wall). Pan heads only, not countersunk.
- No rail: hang it on the screws — Lift the cabinet in front of the screws and push it back against the wall, so the screw heads go through the round holes in the fittings and inserts.
- No rail: keyhole plates, adjust, tighten — From inside, push a keyhole plate 103693 over each screw head and slide it down so the head sits in the slot. Adjust the cabinet sideways and up or down, then tighten both screws with a flat screwdriver.
- No rail: covers on — Push a cover 124518 over each suspension fitting, towards the side panel, until it clicks into place.
- Done! — Your METOD wall cabinet frame is up. Doors, shelves and interior fittings are sold separately and have their own manuals.
METOD wall cabinet frame: questions and answers
How long does it take to assemble the IKEA METOD wall cabinet frame?
About 30–45 min for 1 person, working through the 26 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the METOD wall cabinet frame?
Phillips screwdriver, flat screwdriver, hammer, clamps (only to join cabinets).
Can one person assemble the METOD wall cabinet frame?
Yes, it is a one-person build.
Does the METOD wall cabinet frame need to be fixed to the wall?
The manual shows a wall fixing: see step 15 (Rail: hang it on the suspension rail) and step 21 (No rail: mark the wall, set it aside). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the METOD wall cabinet frame once assembled?
60x37x80 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the METOD wall cabinet frame?
37 fittings of 8 kinds, the most numerous being 8 × cam screw, 8 × cam lock, 8 × dowel. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA METOD wall cabinet frame assembly instructions PDF?
The official PDF is manual AA-2238433-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 302.055.28 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2238433-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
- IKEA EKET cabinet assembly instructions
- IKEA BRIMNES bookcase assembly instructions
All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained