IKEA SKRUVBY bookcase assembly instructions
How to assemble the IKEA SKRUVBY bookcase, step by step: 29 animated steps built from the official manual, about 1–1.5 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer, spirit level.
White SKRUVBY bookcase: a cam-lock frame built lying on its back, screw-in feet, a folding back panel held by clips, three shelves and an adjustable wall fixing. Size: 60×37.5×140 cm (23 5/8×14 3/4×55 1/8"). About 1–1.5 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer, Spirit level.
Based on the official IKEA manual AA-2313530-5 (PDF). Guide updated .
| Steps | 29 |
|---|---|
| Time | 1–1.5 hours |
| People | 2 |
| Tools | Flat-blade screwdriver, Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer, Spirit level |
| Size | 60×37.5×140 cm (23 5/8×14 3/4×55 1/8") |
| Official manual | AA-2313530-5 |
| IKEA article number | 405.035.46 (white) |
| Pieces in the box | 76 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Base | 1 | |
| Top | 1 | |
| Side panel | 2 | |
| Folding back panel | 1 | |
| Shelf | 3 | |
| Foot | 152676 | 4 |
| Cam pin | 10047135 | 8 |
| Dowel | 101345 | 8 |
| Cam lock 10078589/10069936 | 8 | |
| Back clip | 10093081 | 12 |
| Clip wedge | 10093082 | 12 |
| Shelf support 10075382/10051660 | 12 | |
| Cover 133303/133304 | 2 | |
| Wall kit 327495: bracket 150688, knob 150689, washer 126916, screw 147968 or 158469, plug | 121714 | 2 |
Steps
- Feet on the base — Lay the base upside down on a rug or the empty box, so the four threaded inserts face up. Screw a foot (152676) into each insert by hand, clockwise. Check: Work on a soft surface so the moulded edges do not get scratched.
- Turn the base over, cam pins in — Turn the base over onto its feet. Push a cam pin (10047135) into each of the 4 holes near the ends, threaded end down, until it is flush. Push them in by hand: do not screw them. Check: The rounded head points up; a pin put in the wrong way round cannot be locked.
- Dowels in the side panels — Lay both side panels flat, inner side (the one with the rows of holes) up. Push 2 dowels (101345) into the holes in the lower end of each panel: 4 dowels.
- Left side onto the base — Stand the base on its back edge, feet facing out. Stand the left side panel on its back edge too, inner side facing in, and push its dowels and holes onto the base and its cam pins. Check: The bookcase is put together lying on its back on the floor.
- Lock the left side — Put a cam lock (10078589) into each of the 2 round holes in the left side, next to the base, arrow towards the edge. Turn each one clockwise with a flat screwdriver until it grips the cam pin.
- Right side onto the base — Stand the right side panel on its back edge, inner side facing in, and push it onto the base the same way, onto the dowels and cam pins.
- Lock the right side — Put a cam lock (10078589) into each of the 2 round holes in the right side, next to the base, and turn it clockwise with the flat screwdriver until it is tight.
- Slide in the back panel — Unfold the back panel. From the open top end, slide it into the grooves in both side panels, holes towards the top, until its lower edge drops into the groove in the base.
- Stand it up, dowels in the sides — Stand the frame up on its feet. Push 2 dowels (101345) into the holes in the upper end of each side panel: 4 dowels. Check: Lift it with two people so the joints are not strained.
- Cam pins in the top — Lay the top upside down on the rug. Push a cam pin (10047135) into each of the 4 holes near its ends, the same way as in the base.
- Put the top on — Turn the top over and lower it onto the side panels, moulded edge at the front, so the dowels and cam pins go into its holes.
- Lock the top — Put a cam lock (10078589) into each of the 4 round holes just under the top and turn it clockwise with the flat screwdriver until it is tight.
- Shelf supports — Push 12 shelf supports (10075382) into the holes in the side panels: 4 for each shelf, front and back, at the same height on both sides.
- Put in the shelves — Slide each of the 3 shelves in above its supports and lower it onto them. The rounded long edge goes to the front.
- Clip the back panel — Turn the bookcase round. Push a clip (10093081) into each of the 12 holes behind the back panel: 4 in each side, 2 in the top and 2 in the base. Push a wedge (10093082) into each clip so it holds the back panel.
- Wall brackets — Open the wall kit. At each top back corner, push a wall bracket (150688) into the 2 holes in the side panel, behind the back panel, with the round threaded part towards the middle over the hole in the back panel.
- Knobs (only with a skirting board) — If your wall has a skirting board, screw a knob (150689) onto each wall bracket, clockwise, all the way. Without a skirting board, leave the knobs out and push the bookcase straight against the wall in the next step.
- Set the knobs — Turn each knob out (anticlockwise) until it sticks out past the back edge by about the thickness of your skirting board.
- Against the wall — Turn the bookcase round and move it to its place. Push it back until the base rests against the skirting board and both knobs touch the wall, so it stands straight. Check: If a knob does not touch the wall, turn it out a little more.
- Check it is level — Put a spirit level on the top, first across the width and then front to back.
- Level it with the feet — Turn the 4 feet (152676) in or out by hand until the bookcase stands level and does not rock.
- Mark the wall — Reach in at the top and mark the wall with a pencil through the hole in the back panel and wall bracket, in both corners. Check: Read the tip-over warning: this bookcase must be fixed to the wall.
- Move the bookcase away — Pull the bookcase out and move it to the side, clear of the two marks.
- Drill the holes — Drill a hole at each mark: Ø 8 mm and about 70 mm deep in a solid wall, 30 mm in a hollow wall, or Ø 3 mm into solid wood (no plugs needed there). Check: The screws and plugs suit most solid and hollow walls. If you are unsure, ask a specialist.
- Plugs in, bookcase back — Tap a plug (121714) into each hole with a hammer until it is flush with the wall. Then push the bookcase back to its place against the wall.
- Screw the left corner to the wall — From inside, put a washer (126916) on a long screw (147968) and screw it through the hole into the wall. Without a skirting board (no knobs), use the short screws (158469). Check: The hollow side of the washer faces the screw head, not the back panel.
- Screw the right corner to the wall — Do the same in the right corner: washer (126916), long screw (147968), screwed in until it is tight.
- Covers — Press a cover (133303/133304) over each washer and screw head until it clicks.
- Done! — Your SKRUVBY bookcase is assembled and fixed to the wall. Max load per shelf: 13 kg.
SKRUVBY bookcase: questions and answers
How long does it take to assemble the IKEA SKRUVBY bookcase?
About 1–1.5 hours for 2 people, working through the 29 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the SKRUVBY bookcase?
Flat-blade screwdriver, Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer, spirit level.
Can one person assemble the SKRUVBY bookcase?
It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 9 and 11, where the furniture is lifted or turned.
Does the SKRUVBY bookcase need to be fixed to the wall?
The manual shows a wall fixing: see step 16 (Wall brackets) and step 22 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the SKRUVBY bookcase once assembled?
60×37.5×140 cm (23 5/8×14 3/4×55 1/8"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the SKRUVBY bookcase?
68 fittings of 9 kinds, the most numerous being 12 × back clip, 12 × clip wedge, 12 × shelf support 10075382/10051660. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA SKRUVBY bookcase assembly instructions PDF?
The official PDF is manual AA-2313530-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 405.035.46 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2313530-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example foot 152676). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA SKRUVBY cabinet with doors assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
- IKEA EKET cabinet assembly instructions
All IKEA SKRUVBY assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained