Step by StepAssembly Find your furniture

IKEA SKRUVBY cabinet with doors assembly instructions

How to assemble the IKEA SKRUVBY cabinet with doors, step by step: 32 animated steps built from the official manual, about 1.5–2 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer, spirit level.

IKEA SKRUVBY cabinet with doors, assembled

White SKRUVBY cabinet: a cam-lock frame on screw-in feet, a folding back panel held by clips, adjustable wall fixing, two shelves and two grooved doors on clip hinges. Size: 70×37.5×90 cm (27 1/2×14 3/4×35 3/8"). About 1.5–2 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer, Spirit level.

Based on the official IKEA manual AA-2313549-5 (PDF). Guide updated .

SKRUVBY cabinet with doors: quick facts
Steps32
Time1.5–2 hours
People2
ToolsFlat-blade screwdriver, Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer, Spirit level
Size70×37.5×90 cm (27 1/2×14 3/4×35 3/8")
Official manualAA-2313549-5
IKEA article number205.035.47 (white)
Pieces in the box81

In the box

PartPart numberQuantity
Base1
Top1
Side panel2
Folding back panel1
Shelf2
Door2
Foot1526764
Cam pin100471358
Dowel1013458
Cam lock 10078589/100699368
Back clip1009308110
Clip wedge1009308210
Shelf support 10075382/100516608
Hinge100713034
Handle1304172
Screw1004004
Cover 133303/1333042
Bumper sheet 104663 (2 bumpers)2
Wall kit 327495: bracket 150688, knob 150689, washer 126916, screw 147968 or 158469, plug1217142

Steps

  1. Feet on the base — Lay the base upside down on a rug or the empty box, so the four threaded inserts face up. Screw a foot (152676) into each insert by hand, clockwise. Check: Work on a soft surface so the moulded edges do not get scratched.
  2. Turn the base over, cam pins in — Turn the base over onto its feet. Push a cam pin (10047135) into each of the 4 holes near the ends, the threaded end down, until its collar is flush with the board. Push them in by hand: do not screw them. Check: The rounded head points up; a pin put in the wrong way round cannot be locked.
  3. Dowels in the side panels — Lay both side panels flat, inner side (the one with the rows of holes) up. Push 2 dowels (101345) into the holes in each end of both panels: 8 dowels in all.
  4. Stand the sides on the base — Stand each side panel up, inner side facing in, and lower it onto the base so its dowels and the cam pins go into the holes in its lower edge.
  5. Lock the sides to the base — Put a cam lock (10078589) into each of the 4 round holes just above the base, arrow towards the edge. Turn each one clockwise with a flat screwdriver until it grips the cam pin.
  6. Slide in the back panel — Unfold the back panel, smooth side to the front. Slide it down from the top into the grooves in the side panels until its lower edge drops into the groove in the base. Check: The two holes near the top corners of the back panel go at the top.
  7. Cam pins in the top — Lay the top upside down on the rug. Push a cam pin (10047135) into each of the 4 holes near its ends, the same way as in the base.
  8. Put the top on — Turn the top over and lower it onto the side panels, moulded edge at the front, so the dowels and cam pins go into the side panels.
  9. Lock the top — Put a cam lock (10078589) into each of the 4 round holes just under the top and turn it clockwise with the flat screwdriver until it is tight.
  10. Clip the back panel — Turn the cabinet round. Push a clip (10093081) into each of the 10 holes behind the back panel: 3 in each side, 2 in the top and 2 in the base. Push a wedge (10093082) into each clip so it presses the back panel in place.
  11. Wall brackets — Open the wall kit. At each top back corner, push a wall bracket (150688) into the 2 holes in the side panel, behind the back panel, with the round threaded part towards the middle over the hole in the back panel.
  12. Knobs (only with a skirting board) — If your wall has a skirting board, screw a knob (150689) onto each wall bracket, clockwise, all the way. Without a skirting board, leave the knobs out and push the cabinet straight against the wall in the next step.
  13. Set the knobs — Turn each knob out (anticlockwise) until it sticks out past the back edge by about the thickness of your skirting board.
  14. Against the wall — Turn the cabinet round and move it to its place. Push it back until the base rests against the skirting board and both knobs touch the wall, so it stands straight. Check: If a knob does not touch the wall, turn it out a little more.
  15. Check it is level — Put a spirit level on the top, first across the width and then front to back.
  16. Level it with the feet — Turn the 4 feet (152676) in or out by hand until the cabinet stands level and does not rock.
  17. Mark the wall — Reach in at the top and mark the wall with a pencil through the hole in the back panel and wall bracket, in both corners. Check: Read the tip-over warning: this cabinet must be fixed to the wall.
  18. Move the cabinet away — Pull the cabinet out and move it to the side, clear of the two marks.
  19. Drill the holes — Drill a hole at each mark: Ø 8 mm and about 70 mm deep in a solid wall, 30 mm in a hollow wall, or Ø 3 mm into solid wood (no plugs needed there). Check: The screws and plugs suit most solid and hollow walls. If you are unsure, ask a specialist.
  20. Plugs in, cabinet back — Tap a plug (121714) into each hole with a hammer until it is flush with the wall. Then push the cabinet back to its place against the wall.
  21. Screw the left corner to the wall — From inside, put a washer (126916) on a long screw (147968) and screw it through the hole into the wall. Without a skirting board (no knobs), use the short screws (158469). Check: The hollow side of the washer faces the screw head, not the back panel.
  22. Screw the right corner to the wall — Do the same in the right corner: washer (126916), long screw (147968), screwed in until it is tight.
  23. Covers — Press a cover (133303/133304) over each washer and screw head until it clicks.
  24. Shelf supports — Push 8 shelf supports (10075382) into the holes in the side panels: 4 for each shelf, front and back, at the same height on both sides.
  25. Put in the shelves — Slide each shelf in above its supports and lower it onto them. The rounded long edge goes to the front.
  26. Hinges on the doors — Lay both doors on the rug, inner side up. Press a hinge (10071303) into each of the 4 round holes, the mounting plate pointing out past the door edge, until it sits flat.
  27. Hang the left door — With a helper holding the door open, put the hinge plates against the inside of the left side panel, over the holes at the front edge, and tighten their 2 screws each. Check: Two people: one holds the door while the other tightens the screws.
  28. Hang the right door — Hang the right door the same way: hinge plates against the right side panel, 2 screws each.
  29. Hold the handles on — Swing the doors half closed. Hold a handle (130417) against the front of each door, over the two holes near the free edge.
  30. Screw the handles on — Open the doors wide. From the inside of each door, drive 2 screws (100400) through the holes into the handle.
  31. Bumpers on the shelves — Peel the bumpers (104663) off their sheets and stick 2 on the front edge of each shelf, left of the middle as drawn. Then close the doors.
  32. Done! — Your SKRUVBY cabinet is assembled and fixed to the wall. Max load per shelf: 15 kg. To line the doors up, turn the hinge screws as shown on manual page 30.

SKRUVBY cabinet with doors: questions and answers

How long does it take to assemble the IKEA SKRUVBY cabinet with doors?

About 1.5–2 hours for 2 people, working through the 32 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the SKRUVBY cabinet with doors?

Flat-blade screwdriver, Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer, spirit level.

Can one person assemble the SKRUVBY cabinet with doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 4 and 8, where the furniture is lifted or turned.

Does the SKRUVBY cabinet with doors need to be fixed to the wall?

The manual shows a wall fixing: see step 11 (Wall brackets) and step 17 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the SKRUVBY cabinet with doors once assembled?

70×37.5×90 cm (27 1/2×14 3/4×35 3/8"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the SKRUVBY cabinet with doors?

70 fittings of 12 kinds, the most numerous being 10 × back clip, 10 × clip wedge, 8 × cam pin. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA SKRUVBY cabinet with doors assembly instructions PDF?

The official PDF is manual AA-2313549-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 205.035.47 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2313549-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example foot 152676). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA SKRUVBY assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained