Step by StepAssembly Find your furniture

IKEA GULLABERG bedside table assembly instructions

How to assemble the IKEA GULLABERG bedside table (nightstand), step by step: 27 animated steps built from the official manual, about 50 min for 1 person, with flat-blade screwdriver, Phillips screwdriver.

IKEA GULLABERG bedside table, assembled

A white GULLABERG bedside table on four tapered legs, with a drawer on roller runners and an open shelf below, built from two ready-made side frames joined by rails and cam locks. Size: 53x43x69 cm. About 50 min, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver.

Based on the official IKEA manual AA-2537632-3 (PDF). Guide updated .

GULLABERG bedside table: quick facts
Steps27
Time50 min
People1
ToolsFlat-blade screwdriver, Phillips screwdriver
Size53x43x69 cm
Official manualAA-2537632-3
IKEA article number205.617.40 (drawer shelf white)
Pieces in the box83

In the box

PartPart numberQuantity
Side frame (2 legs + side apron)2
Back panel1
Top rail1
Lower rail1
Tabletop1
Shelf1
Drawer front1
Drawer side2
Drawer bottom1
Drawer back1
Runner set 10102056 (CL, CR, DL, DR)1
Knob100959781
Screw1066031
Cam screw11833114
Dowel10134516
Cam lock1313618
Cam lock11925110
Plastic pin1457184
Screw1461148
Glide1123574
Shelf support100460784

Steps

  1. Drawer front: cam screws — The drawer comes first. Lay the drawer front face down on a soft surface. Screw 4 cam screws 118331 into the holes near its two ends, 2 at each end, with a Phillips screwdriver. Check: Screw them in only until the collar touches the panel.
  2. Dowels in the drawer sides — Lay the 2 drawer sides flat. Push 2 dowels 101345 into the holes in the front end of each side.
  3. Sides onto the front — Stand the 2 sides on the drawer front, dowel end down and the grooves facing each other, over the dowels and cam screws. Press them down until they sit tight on the front. Check: The groove near the top of each side must face inwards.
  4. Lock the sides — Push 4 cam locks 131361 into the holes in the outside of the sides, 2 per side, arrow towards the cam screw. Turn each half a turn clockwise with a flat screwdriver to lock it. Check: Use cam lock 131361 here, not the similar 119251.
  5. Slide in the drawer bottom — Slide the drawer bottom down into the grooves of the two sides until it sits in the groove of the front.
  6. Drawer back — Lay the drawer back between the sides at the open end, on the drawer bottom, holes facing out.
  7. Pins through the sides — Push 4 plastic pins 145718 through the holes at the back end of the sides into the drawer back, 2 per side.
  8. Lock the back — Push 4 cam locks 131361 into the holes in the drawer back, 2 at each end. Turn each half a turn clockwise with a flat screwdriver so it grips the pin. Check: Use cam lock 131361 here, not the similar 119251.
  9. Drawer runners — Turn the drawer upright. Fit runner DR on the right side and DL on the left, at the bottom edge with the wheel at the back, each with 2 screws 146114. Check: The runners are marked DR and DL: do not swap them.
  10. The knob — Hold the knob against the front. From inside the drawer, put screw 106603 through the hole and screw it into the knob with a Phillips screwdriver.
  11. Cabinet runners on the frames — Set the drawer aside. Lay the 2 side frames flat, inside up. Fit runner CL on the left frame and CR on the right, along the apron at the bottom edge with the wheel at the front, each with 2 screws 146114. Check: Line the runner up with the front edge of the apron, as drawn.
  12. Cam screws in the frames — Screw 3 cam screws 118331 into the inside of each frame by hand: one at the top of the front leg, one at the bottom of the apron by the front leg, one in the back leg. Check: Screw them in until the collar touches the wood, no further.
  13. Dowels in the rails and back panel — Push 8 dowels 101345 into the end holes: 1 in each end of the top rail and the lower rail, and 2 in each end of the back panel.
  14. Back panel on the left frame — Stand the back panel on the left frame at the back leg, cam lock holes facing the front, and press it down over the dowels and the cam screw.
  15. Top rail and lower rail — Stand the top rail at the top of the front leg and the lower rail below it, cam lock holes towards the top and the bottom of the table, and press them down over the dowels and cam screws.
  16. Lock the left frame — Push 3 cam locks 119251 into the holes in the top rail, the lower rail and the back panel at the left frame. Turn each half a turn clockwise with a flat screwdriver.
  17. Second side frame — Lift the second side frame over, inside down and feet the same way as the first, and lower it onto the rails and the back panel, over the dowels and cam screws.
  18. Lock the second frame — Push 3 cam locks 119251 into the holes in the top rail, the lower rail and the back panel at the second frame. Turn each half a turn clockwise to lock it.
  19. Glides in the feet — Turn the table upside down, onto its top edges. Push a glide 112357 into the hole in the end of each of the 4 legs.
  20. Turn upright, top dowels — Turn the table over onto its feet. Push 4 dowels 101345 into the top edges of the two side aprons, 2 in each.
  21. Cam screws in the tabletop — Lay the tabletop upside down on a soft surface. Screw 4 cam screws 118331 into the holes in its underside by hand, one near the middle of each edge.
  22. Put on the tabletop — Turn the tabletop over and lower it onto the frame, so the dowels and cam screws go into the holes in the aprons, the back panel and the top rail.
  23. Lock the tabletop — Reach in through the drawer opening. Push 4 cam locks 119251 into the holes in the two side aprons, the back panel and the top rail, just under the tabletop. Turn each half a turn clockwise.
  24. Shelf supports — Push 4 shelf supports 10046078 into the holes low down on the legs: into the back of each front leg and the front of each back leg.
  25. The shelf — Tilt the shelf and slide it in between the legs from the front. Level it and lower it onto the 4 supports, notched corners round the legs. Check: Lower the shelf straight down: do not let it scrape the legs.
  26. Slide in the drawer — Hold the drawer in front of the opening with the front slightly raised, set its back wheels on the runners and push it in until it closes.
  27. Done! — Your GULLABERG bedside table is assembled.

GULLABERG bedside table: questions and answers

How long does it take to assemble the IKEA GULLABERG bedside table?

About 50 min for 1 person, working through the 27 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the GULLABERG bedside table?

Flat-blade screwdriver, Phillips screwdriver.

Can one person assemble the GULLABERG bedside table?

Yes, it is a one-person build.

What size is the GULLABERG bedside table once assembled?

53x43x69 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the GULLABERG bedside table?

70 fittings of 10 kinds, the most numerous being 16 × dowel, 14 × cam screw, 10 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA GULLABERG bedside table assembly instructions PDF?

The official PDF is manual AA-2537632-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 205.617.40 (drawer shelf white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2537632-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example runner set 10102056). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained