Step by StepAssembly Find your furniture

IKEA KNOXHULT base cabinet with doors and drawer assembly instructions

How to assemble the IKEA KNOXHULT base cabinet with doors and drawer, step by step: 58 animated steps built from the official manual, about 2–3 hours for 2 people, with flat-blade screwdriver, Phillips screwdriver, hammer, pencil, clamps, spirit level, wall screws and plugs (not included).

IKEA KNOXHULT base cabinet with doors and drawer, assembled

A 120 cm white KNOXHULT kitchen base cabinet with its worktop: a dowelled and bolted frame built lying on its front, a nailed-on back, wall fixing, two hinged doors, two shelves and a drawer on runners. Size: 120x61x91 cm. About 2–3 hours, 2 people. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer, Pencil, Clamps, Spirit level, Wall screws and plugs (not included).

Based on the official IKEA manual AA-1849533-10 (PDF). Guide updated .

KNOXHULT base cabinet with doors and drawer: quick facts
Steps58
Time2–3 hours
People2
ToolsFlat-blade screwdriver, Phillips screwdriver, Hammer, Pencil, Clamps, Spirit level, Wall screws and plugs (not included)
Size120x61x91 cm
Official manualAA-1849533-10
IKEA article number303.267.90 (white)
Pieces in the box144

In the box

PartPart numberQuantity
Side panel2
Bottom panel1
Post2
Top middle bar1
Top rail2
Plinth1
Back panel1
Worktop 122 × 61 cm1
Door2
Shelf2
Drawer front1
Drawer side2
Drawer back1
Drawer bottom1
Allen key1000011
Connector bolt1002148
Screw10034415
Screw10036512
Nails 101221 (bag)1
Dowel1013452
Dowel10135020
Leg sleeve1014495
Shelf pin1015328
Foot1030955
Cam lock1034304
Wall plate1036933
Angle bracket1037171
Screw1053443
Bumpers 107091 (sheet of 2)3
Screw1090298
Plastic pin1105192
Wall bracket1157533
Cam screw 118331/1129966
Cam lock1190302
Screw1485102
Hinge1178774
Hinge mounting plate1186924
Drawer runner set 139505 (4 rails)1
Drawer bottom rail1183011

Steps

  1. Feet in the side panels — Lay both side panels flat on a soft surface, inside faces up. Tap 2 leg sleeves 101449 into the bottom edge of each panel with a hammer, then screw a foot 103095 into each sleeve by hand. Check: The edge with the narrow groove is the back edge.
  2. Cam screws for the bottom panel — Screw 2 cam screws 118331 into the inside face of each side panel, in the holes near the bottom end where the bottom panel will sit.
  3. Wall brackets on the side panels — Fix a wall bracket 115753 at the top back corner of each side panel with 2 screws 100344. The leg with the big hole stands up along the back edge. Check: Use the screws 100344 here, not the shorter 100365.
  4. Dowels in the bottom panel — Lay the bottom panel down and push 2 dowels 101350 into each of its short ends. Check: Use the thicker dowels 101350, not 101345.
  5. Bottom panel onto the left side — Stand the left side panel on its front edge, inside facing the room. Stand the bottom panel on its front edge too and push it onto the side panel so its dowels and the cam screws go into the holes.
  6. Lock the bottom panel — Put 2 cam locks 103430 into the holes in the underside of the bottom panel, next to the side panel, and turn them clockwise with a flat screwdriver until they grip the cam screws. Check: Use the cam locks 103430 here, not 119030.
  7. Wall bracket on the back post — Lay the two posts down. Fix the third wall bracket 115753 near one end of the back post with 2 screws 100344, the leg with the hole standing up at the back edge. Check: Use the screws 100344, not 100365.
  8. Dowels in the posts — Push a dowel 101350 into each end of both posts.
  9. Front post onto the bottom panel — Turn the front post upright on its narrow side and push its dowel into the middle hole near the front edge of the bottom panel.
  10. Bolt the front post — From the underside of the bottom panel, drive a connector bolt 100214 into the end of the post with the Allen key 100001.
  11. Middle top bar — Push 2 dowels 101350 into each end of the short middle bar. Press one end onto the top end of the front post, on the face that points to the back.
  12. Back post on — Put the bottom dowel of the back post into the bottom panel, next to the back edge, then lower its top end onto the dowels of the middle bar. The wall bracket ends up at the top.
  13. Bolt the back post — Drive a connector bolt 100214 through the bottom panel into the end of the back post with the Allen key.
  14. Dowels in the top rails — Push a dowel 101350 into each end of both top rails.
  15. Top rails on — Fit the two rails across the top end, one at the back and one at the front: put the dowel of the left end into the left side panel, then swing the rail down onto the dowel in the end of the post.
  16. Bolt the top rails — With the Allen key, drive 2 connector bolts 100214 through the left side panel into the ends of the rails, and 2 through the rails into the top ends of the posts.
  17. Foot in the plinth — Lay the plinth down. Tap a leg sleeve 101449 into the hole in the middle of its bottom edge and screw a foot 103095 into it.
  18. Angle bracket on the plinth — Screw the small angle bracket 103717 to the back face of the plinth, in the middle along its top edge, with a screw 105344.
  19. Dowels in the plinth — Push 2 dowels 101350 into each end of the plinth.
  20. Plinth in — Hold the plinth on its edge under the front of the bottom panel, bracket at the top, and push its dowels into the left side panel.
  21. Fix the plinth to the bottom — Screw the angle bracket to the underside of the bottom panel with a screw 105344.
  22. Right side panel on — Stand the right side panel on its front edge and push it onto the free ends of the bottom panel, rails and plinth. Drive 2 connector bolts 100214 through it into the ends of the rails.
  23. Lock the right side — Put 2 cam locks 103430 into the underside of the bottom panel next to the right side panel and turn them clockwise to lock.
  24. Mark the back post — Mark the middle of the back post with a pencil on the back edges of the top rail and of the bottom panel. The back panel will cover the post, and the marks show where to nail.
  25. Back panel and the first nail — Lay the back panel on the back of the frame, white side down, and line it up with the edges at the top left corner. Hammer in a nail 101221 there. Check: Keep the edges of the back panel flush with the frame before each corner nail.
  26. Second corner — Push the back panel flush at the top right corner and nail it there.
  27. Third corner — Square the frame so the panel lines up at the bottom left corner, and nail it there.
  28. Nail all round — Hammer in 21 more nails 101221 along the side panels, the top rail and the bottom panel.
  29. Line for the back post — Draw a pencil line across the back panel from the mark on the top rail to the mark on the bottom panel. The back post is under this line.
  30. Nail along the line — Hammer 6 nails 101221 along the line into the back post.
  31. Stand it up — Tip the cabinet up over its front bottom edge until it stands on its feet. Check: Get help to stand the cabinet up.
  32. Runners in the frame — Screw a runner from set 139505 along the top of the right side panel and another across the two posts, wheels at the front. Use 3 screws 100365 for each runner. Check: Use the short screws 100365 here, not 100344.
  33. Front screws of the runners — Fix the front end of each runner with a screw 148510. Check: Use the screws 148510, not 105344.
  34. Worktop on — Lay the worktop on the cabinet, flush with the back and overhanging 1 cm at each side, and hold it in place with clamps. Check: If the cabinet stands next to another KNOXHULT cabinet, let the worktop overhang 2 cm on the free side instead.
  35. Screw the worktop on — From underneath, drive 8 screws 109029 up through the top rails into the worktop: 5 through the front rail and 3 through the back rail.
  36. Level the cabinet — Turn the 5 feet by hand until the cabinet stands level and steady.
  37. Mark the wall — Push the cabinet against the wall where it will stand. With a pencil, mark the wall through the hole in each of the 3 wall brackets. Check: The cabinet must be fixed to the wall. Screws and plugs for the wall are not included: choose ones that suit your wall.
  38. Plugs and wall screws — Move the cabinet away. Drill at the 3 marks, tap in plugs that suit your wall and drive in 3 screws with a round head, leaving each head about 1.5 cm out from the wall. Check: Use round (pan) head screws, not countersunk ones.
  39. Hang it on the wall — Push the cabinet back so the screw heads come through the brackets. Slide a wall plate 103693 down into each bracket so its keyhole hooks over the screw head. Adjust the cabinet sideways and up or down.
  40. Tighten the wall screws — Tighten the 3 wall screws through the wall plates with a screwdriver.
  41. Hinge plates on the right side — Screw 2 hinge mounting plates 118692 to the inside of the right side panel near the front edge, one under the drawer runner and one near the bottom. Their screws come fitted.
  42. Hinge plates on the left side — Screw 2 hinge mounting plates 118692 to the inside of the left side panel in the same way, near the top and near the bottom.
  43. Hinges on the doors — Lay both doors face down. Press 2 hinges 117877 into the round holes of each door, arms pointing outwards, and fix each hinge with 2 screws 100344. Check: Use the screws 100344, not 100365.
  44. Hang the doors — Slide each hinge arm onto its mounting plate in the cabinet and press until it clicks, then tighten the screw on the hinge arm. Check: The hinge screws adjust the doors up and down, sideways and in and out.
  45. Shelves — Push 8 shelf pins 101532 into the side panels and posts, 4 at the same height in each compartment. Lay a shelf on each set of pins, then close the doors.
  46. Cam screws in the drawer front — Lay the drawer front face down. Screw 2 cam screws 118331 into the holes near its ends on the inside.
  47. Screw for the bottom rail — Screw a screw 100344 into the middle hole on the groove line of the drawer front. Leave the head standing out a few millimetres: the bottom rail hooks onto it. Check: Do not screw it in all the way.
  48. Dowels in the drawer sides — Push a dowel 101345 into the hole in the front end of each drawer side. Check: Use the thin dowels 101345 here.
  49. Sides onto the front — Stand both sides on the drawer front, grooves facing each other, so the dowels and cam screws go into the holes in their ends.
  50. Lock the sides — Put a cam lock 119030 into the hole on the outside of each side and turn it clockwise with a flat screwdriver to lock.
  51. Bottom rail — Hook the bottom rail 118301 onto the head of the screw in the drawer front, so it stands up in the middle between the sides.
  52. Drawer bottom — Slide the drawer bottom down into the grooves of the sides and the front, in front of the rail.
  53. Drawer back — Fit the drawer back between the free ends of the sides, over the bottom. Tap a plastic pin 110519 through each side into the ends of the back.
  54. Fix the rail to the back — Press the free end of the bottom rail against the drawer back and fix its tab to the back with a screw 105344.
  55. Runners on the drawer — Turn the drawer upright. Fix a drawer runner from set 139505 along the bottom of each side, wheel at the back, with 3 screws 100365 each.
  56. Put the drawer in — Hold the drawer level in front of its opening, rest its wheels on the runners and push it all the way in.
  57. Bumpers — Open the doors and the drawer. Stick the 6 bumpers 107091 on the front edges of the frame where the doors and drawer close: 5 on the front post and 1 on the right side panel. Then close them.
  58. Done! — Your KNOXHULT base cabinet is finished and fixed to the wall. The shelves can be moved to other heights with the shelf pins.

KNOXHULT base cabinet with doors and drawer: questions and answers

How long does it take to assemble the IKEA KNOXHULT base cabinet with doors and drawer?

About 2–3 hours for 2 people, working through the 58 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the KNOXHULT base cabinet with doors and drawer?

Flat-blade screwdriver, Phillips screwdriver, hammer, pencil, clamps, spirit level, wall screws and plugs (not included).

Can one person assemble the KNOXHULT base cabinet with doors and drawer?

It is planned as a 2-person build. One person can do most of it, but get help for step 31, where the furniture is lifted or turned.

Does the KNOXHULT base cabinet with doors and drawer need to be fixed to the wall?

The manual shows a wall fixing: see step 3 (Wall brackets on the side panels) and step 7 (Wall bracket on the back post). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the KNOXHULT base cabinet with doors and drawer once assembled?

120x61x91 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the KNOXHULT base cabinet with doors and drawer?

118 fittings of 21 kinds, the most numerous being 20 × dowel, 15 × screw, 12 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA KNOXHULT base cabinet with doors and drawer assembly instructions PDF?

The official PDF is manual AA-1849533-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 303.267.90 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1849533-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example allen key 100001). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained