Step by StepAssembly Find your furniture

IKEA NORDKISA bedside table assembly instructions

How to assemble the IKEA NORDKISA bedside table (nightstand), step by step: 14 animated steps built from the official manual, about 40 min for 1 person, with Allen key (supplied), Phillips screwdriver.

IKEA NORDKISA bedside table, assembled

A light bamboo bedside table with a slatted bottom shelf, an open shelf and a loose drawer that rests on two rails, built from two ready-made side frames with 16 Allen screws, then topped and finished with a screwed-together drawer. Size: 40x40 cm, bamboo. About 40 min, 1 person. Tools: Allen key (supplied), Phillips screwdriver.

Based on the official IKEA manual AA-2523518-2 (PDF). Guide updated .

NORDKISA bedside table: quick facts
Steps14
Time40 min
People1
ToolsAllen key (supplied), Phillips screwdriver
Size40x40 cm, bamboo
Official manualAA-2523518-2
IKEA article number604.476.77 (bamboo)
Pieces in the box41

In the box

PartPart numberQuantity
Side frame (2 legs + top rail)2
Slatted bottom shelf1
Shelf1
Drawer rail2
Tabletop1
Drawer end (with finger notch)2
Drawer side2
Drawer bottom1
Allen screw1004062516
Dowel1013454
Screw1053648
Allen key1000061

Steps

  1. Side frame and slatted shelf — Work on a soft surface. Lay the table out on its back: stand one side frame on its edge, feet to your left. Put the slatted shelf against it at the foot end and fix it with 2 Allen screws 10040625, one through each leg. Turn them clockwise with the Allen key. Check: The holes in the frame must have their plain side facing out, and the 2 holes in the slatted shelf go against the legs.
  2. The shelf — Put the plain shelf against the frame at the top-rail end, notched corners round the legs, and fix it with 2 Allen screws 10040625 through the legs. Check: Check the notches: the hole in the end of the shelf must face the leg.
  3. The two drawer rails — Put the 2 drawer rails against the frame between the two shelves, one at the front leg and one at the back leg. Fix each with 1 Allen screw 10040625 through the leg.
  4. Second side frame — Tip the table over onto the frame, so the shelves and rails stand up. Lower the second side frame onto their ends, feet at the same end as the first frame. Check: The wide, countersunk side of the holes faces up.
  5. Screw on the second frame — Fix the second frame with 6 Allen screws 10040625, down through the legs into the slatted shelf, the rails and the shelf. Turn them clockwise with the Allen key.
  6. Stand it up, add the dowels — Stand the table upright on its feet. Push 4 dowels 101345 into the holes on top of the two top rails, 2 in each.
  7. Put on the tabletop — Lay the tabletop on the frames with its holes underneath, over the dowels, and press it down.
  8. Screw the tabletop on — From the open shelf, drive 4 Allen screws 10040625 up through the top rails into the tabletop, 2 in each rail. Tighten them clockwise with the Allen key.
  9. Drawer: one end and a side — Stand a drawer end on its long edge, notch up and cleats facing in. Put a drawer side against the end of it and fix it with 2 screws 105364 into the cleat, using a Phillips screwdriver. Check: The small notch at the bottom corner of the side goes down, next to the cleat.
  10. Drawer: the other end — Put the second drawer end against the other end of the side, notch up, and fix it with 2 screws 105364.
  11. Slide in the drawer bottom — Turn the drawer over onto the side you just fitted. Slide the drawer bottom down into the grooves in the two ends until it rests on that side.
  12. Second drawer side — Lay the second drawer side on top, over the cleats, and fix it with 4 screws 105364, 2 into each cleat.
  13. Slide in the drawer — Turn the drawer upright. Hold it level with the opening under the shelf and slide it in from the front, so it runs on the two rails.
  14. Done! — Your NORDKISA bedside table is assembled.

NORDKISA bedside table: questions and answers

How long does it take to assemble the IKEA NORDKISA bedside table?

About 40 min for 1 person, working through the 14 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the NORDKISA bedside table?

Allen key (supplied), Phillips screwdriver. Already in the box: Allen key.

Can one person assemble the NORDKISA bedside table?

Yes, it is a one-person build.

What size is the NORDKISA bedside table once assembled?

40x40 cm, bamboo, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the NORDKISA bedside table?

28 fittings of 3 kinds, the most numerous being 16 × allen screw, 8 × screw, 4 × dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA NORDKISA bedside table assembly instructions PDF?

The official PDF is manual AA-2523518-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.476.77 (bamboo); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2523518-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example allen screw 10040625). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained