Step by StepAssembly Find your furniture

IKEA SUNDVIK cot assembly instructions

How to assemble the IKEA SUNDVIK cot, step by step: 30 animated steps built from the official manual, about 45–60 min for 1 person, with flat-blade screwdriver, Phillips screwdriver, Allen key (included).

IKEA SUNDVIK cot, assembled

White cot for a 70x140 cm mattress: two end panels with legs, two barred sides and a base at two heights; one side swaps for a low rail to make a junior bed. Size: 70x140 cm. About 45–60 min, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Allen key (included).

Based on the official IKEA manual AA-2379187-2 (PDF). Guide updated .

SUNDVIK cot: quick facts
Steps30
Time45–60 min
People1
ToolsFlat-blade screwdriver, Phillips screwdriver, Allen key (included)
Size70x140 cm
Official manualAA-2379187-2
IKEA article number604.975.87 (white)
Pieces in the box47

In the box

PartPart numberQuantity
End panel with legs2
Side panel2
Base1
Rail for the junior bed1
Bolt1059078
Dowel1013518
Cross nut1005148
Hole cover1192454
Screw1471684
Bolt1486244
L-pin100507974
Allen key1000921

Steps

  1. Dowels into the side panels — Lay both side panels flat. Push a dowel (101351) into the small hole in the end of each rail: 4 per panel, 8 in all.
  2. Sides against the first end — Stand one end panel up. Lift each side panel upright and push its dowels into the holes in the end panel's posts, back side first, then the front.
  3. Bolt the sides to the first end — Push a cross nut (100514) up into the hole under each rail end, lining it up with the flat screwdriver. Then screw a bolt (105907) through each post into it with the allen key, 4 in all.
  4. On its end, second end on top — Turn the frame over so it stands on the end panel. Lower the second end panel onto the dowels at the top of the side rails.
  5. Bolt the second end on — Push 4 cross nuts (100514) into the rail ends below it, lined up with the flat screwdriver. Screw 4 bolts (105907) down through the posts into them with the allen key.
  6. Stand it up, L-pins in — Stand the cot on its legs. Push the 4 L-pins (10050797) into the holes inside the end panels, threaded end up: the upper holes for a newborn, the lower holes once your baby can stand.
  7. Base onto the pins — Lower the base into the cot with the label facing up, so the threaded ends of the 4 L-pins go into the holes in its corners. Check: The corner fittings must sit flush with the edge of the base, not turned out.
  8. Bolt the base to the pins — Screw a bolt (148624) down through each corner of the base into the L-pin below with the allen key, 4 in all.
  9. Hole covers at the first end — Push a hole cover (119245) into the empty hole just above the bottom side rail on the inside of each post, then screw it on from outside with a screw (147168) and a Phillips screwdriver.
  10. Hole covers at the other end — Fit the other 2 hole covers (119245) the same way at the second end panel, each screwed on from outside (147168). The cot is ready, with the base at the upper height.
  11. Later: undo the base bolts — To lower the base once your baby can stand, undo the 4 bolts (148624) in the corners of the base with the allen key.
  12. Later: lift the base out — Lift the base up out of the cot and put it down to one side.
  13. Later: pins to the lower holes — Pull each L-pin (10050797) out of its upper hole and push it into the lower hole below it, 4 in all.
  14. Later: base onto the lower pins — Lift the base back over the cot and lower it, label up, onto the pins in the lower holes.
  15. Later: bolt the base back on — Screw the 4 bolts (148624) back down through the corners of the base into the L-pins with the allen key.
  16. Junior bed: free the front side — To make a junior bed, keep the base in the lower holes. At one end, undo the 2 bolts (105907) of the front side with the allen key and take out their cross nuts (100514). Unscrew that end's front hole cover (147168, 119245).
  17. Junior bed: other front cover off — At the other end, unscrew the front hole cover too: screw (147168) out from outside, then pull the cover (119245) off the inside of the post.
  18. On its end, undo the top end — Turn the cot onto the end you just worked on. Undo the 4 bolts (105907) in the top end panel with the allen key and push the 4 cross nuts (100514) out of the rails.
  19. Top end off, front side away — Lift the top end panel off; the base pins slide out of its holes. Then lift the front side panel off the dowels in the bottom end panel and lay it down.
  20. Dowels out of the side panel — Pull the 4 dowels (101351) out of the ends of the front side panel's rails. Keep the side panel for later.
  21. Dowels into the rail — Lay the plain rail flat and push 2 of those dowels (101351) into each end of it.
  22. Cross nuts into the rail — Push 2 cross nuts (100514) into the holes in the face of the rail, one near each end, with the threaded hole lined up with the end of the rail. Check: Turn each nut so its threaded hole points along the rail towards the end, as in the manual's close-up, or the bolt will not catch.
  23. Rail into the bottom end — Stand the rail up where the front side was, nuts towards the base, and slide it down so its dowels go into the bottom end panel.
  24. Top end back on — Lower the end panel back on top so the dowels of the rail and the back side and the base pins go into its holes.
  25. Bolt the back side — Push 2 cross nuts (100514) back into the back side's rails and screw 2 bolts (105907) down through the posts into them with the allen key.
  26. Bolt the rail to the top end — Screw a bolt (105907) through the post into the nut already in the rail. Push the third cross nut (100514) into the lower hole in the rail from behind, then screw the second bolt into it.
  27. Stand the bed up — Turn the bed back onto its legs.
  28. Bolt the rail to the other end — At the bottom end, screw a bolt (105907) into the nut in the rail. Push the last cross nut (100514) into the lower hole from behind and screw the second bolt into it with the allen key.
  29. Hole covers at the top — Put the 2 hole covers (119245) into the empty bolt holes at the top of the front posts, on the inside, and screw them on from outside (147168) with the Phillips screwdriver.
  30. Done! — Your SUNDVIK is assembled. Use the upper base height for a newborn, the lower one once your baby can stand, and the junior bed with the low rail when your child can climb in and out.

SUNDVIK cot: questions and answers

How long does it take to assemble the IKEA SUNDVIK cot?

About 45–60 min for 1 person, working through the 30 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the SUNDVIK cot?

Flat-blade screwdriver, Phillips screwdriver, Allen key (included). Already in the box: Allen key.

Can one person assemble the SUNDVIK cot?

Yes, it is a one-person build.

What size is the SUNDVIK cot once assembled?

70x140 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the SUNDVIK cot?

40 fittings of 7 kinds, the most numerous being 8 × bolt, 8 × dowel, 8 × cross nut. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA SUNDVIK cot assembly instructions PDF?

The official PDF is manual AA-2379187-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.975.87 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2379187-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 105907). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA SUNDVIK assembly guides · All beds assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained