IKEA TROTTEN cabinet with doors assembly instructions
How to assemble the IKEA TROTTEN cabinet with doors, step by step: 24 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat screwdriver, Allen key (included), spirit level, wall screws (not included).
A steel office cabinet: two leg frames, side and back panels that slide into place, an open top section bolted together upside down, a middle panel, bottom, shelf and two lockable hinged doors on pins. Size: 70x35x110 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Allen key (included), Spirit level, Wall screws (not included).
Based on the official IKEA manual AA-2241595-6 (PDF). Guide updated .
| Steps | 24 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat screwdriver, Allen key (included), Spirit level, Wall screws (not included) |
| Size | 70x35x110 cm |
| Official manual | AA-2241595-6 |
| IKEA article number | 806.239.62 (light green) |
| Pieces in the box | 35 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Leg frame (2 legs + rail) | 2 | |
| Side panel | 2 | |
| Back panel | 2 | |
| Top | 1 | |
| Side frame for the top section | 2 | |
| Middle panel | 1 | |
| Bottom panel | 1 | |
| Shelf | 1 | |
| Door with lock 10072463 (keys included) | 1 | |
| Door | 1 | |
| Levelling foot | 10036516 | 4 |
| Bolt | 10074126 | 4 |
| Screw | 100404 | 6 |
| Hinge pin | 151059 | 2 |
| Hinge catch | 10056123 | 2 |
| Wall spacer | 114664 | 2 |
| Allen key | 130445 | 1 |
Steps
- Feet into the leg frames — Stand both leg frames upside down. Screw a levelling foot 10036516 into the end of each of the 4 legs by hand, clockwise, until it is snug.
- Frames into the right side panel — Lay the right side panel flat, inside up. Turn both leg frames so the rails point up, then push the top ends of their legs into the channels at the bottom end of the panel until the brackets rest against it. Check: Push the leg ends in all the way: the brackets must sit flat against the panel.
- Stand it up, add the left side — Stand the frame on its feet. Slide the left side panel down over the two free leg ends until it sits on the frame.
- Lower back panel — Hold the lower back panel with its flanges facing into the cabinet and the slotted flange at the bottom. Slide it down between the side panels all the way to the bottom.
- Lock the lower back panel — With a flat screwdriver, bend the 4 tabs in the side flanges out into the slots of the side panels. Then bend the 2 tabs in the bottom flange down.
- Upper back panel — Slide the upper back panel down between the side panels until it rests on the lower one.
- Lock the upper back panel — Bend the lower tab in each side flange of the upper back panel out with the flat screwdriver, then bend the 3 tabs at the joint between the two back panels down. Check: Leave the 2 tabs at the top of the side flanges straight for now. They are bent in step 13.
- Side frames into the top — Lay the top upside down on a soft surface. Stand the two open side frames upside down at its ends and push their post ends into the folded front and back edges of the top.
- Bolt the frames to the top — Push a bolt 10074126 through each of the 4 holes in the front and back edges of the top and tighten it into the bracket of the post with the Allen key.
- Set the top section on — Turn the top section the right way up and lift it over the cabinet. Lower it so the 4 posts slide into the tops of the side panels, and press down until it sits flat. Check: Check all 4 posts are fully down in the side panels before you go on.
- Middle panel — Tip the middle panel in through the open top section, back edge first. Hook its back edge down behind the upper back panel, then swing the front down until it lies flat on the side panels.
- Screw the middle panel to the frames — From above, drive 4 screws 100404 through the low side upstands of the middle panel into the crossbars of the side frames, 2 on each side, with a Phillips screwdriver.
- Two screws from below — Reach into the lower cabinet and drive the last 2 screws 100404 up through the lip at the top of each side panel into the middle panel.
- Lock the top of the back panel — With the flat screwdriver, bend the 2 tabs at the top of the upper back panel's side flanges out into the side panels.
- Lock the middle panel — Bend the 3 tabs at the back of the middle panel down into the top flange of the upper back panel.
- Bottom panel — Tip the bottom panel into the lower cabinet, back edge first and low. Hook the back edge in behind the lower back panel's flange, then swing the front down onto the front rail.
- Shelf — Put the shelf in level and lower it onto the 4 hooks pressed out of the side panels, so it sits on all 4.
- Hinge pins — Press a hinge pin 151059 into the hole at each front corner of the bottom panel, narrow end down.
- Hang the doors — Hold the left door (with the lock) open and lower the hole in its bottom hinge corner onto the left pin. Do the same with the right door on the right pin.
- Top hinge catches — Fit a hinge catch 10056123 into the top hinge corner of each door from the inside. Push it up until its pin clicks into the hole under the middle panel.
- Level the cabinet — Close the doors. Put a spirit level on the middle panel and turn the 4 feet in or out until the cabinet stands level, side to side and front to back.
- Wall spacers — Snap a wall spacer 114664 to the depth of the gap behind the cabinet (e.g. over a skirting board). Hold one behind each fixing hole in the middle panel's back upstand. Check: Fix the cabinet to the wall to stop it tipping over.
- Fix it to the wall — Push the cabinet back against the wall. From the open top section, drive a wall screw through each hole in the back upstand of the middle panel and through the spacer into the wall. Check: Wall screws and plugs are not included. Use ones that suit your wall; ask a specialist if unsure.
- Done! — Your TROTTEN cabinet is ready. The key locks the left door. Max load 15 kg per shelf.
TROTTEN cabinet with doors: questions and answers
How long does it take to assemble the IKEA TROTTEN cabinet with doors?
About 1–1.5 hours for 1 person, working through the 24 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TROTTEN cabinet with doors?
Phillips screwdriver, flat screwdriver, Allen key (included), spirit level, wall screws (not included). Already in the box: Allen key.
Can one person assemble the TROTTEN cabinet with doors?
Yes, it is a one-person build.
Does the TROTTEN cabinet with doors need to be fixed to the wall?
The manual shows a wall fixing: see step 22 (Wall spacers) and step 23 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the TROTTEN cabinet with doors once assembled?
70x35x110 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the TROTTEN cabinet with doors?
20 fittings of 6 kinds, the most numerous being 6 × screw, 4 × levelling foot, 4 × bolt. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TROTTEN cabinet with doors assembly instructions PDF?
The official PDF is manual AA-2241595-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 806.239.62 (light green); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2241595-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example door with lock 10072463). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TROTTEN cabinet with sliding doors assembly instructions
- IKEA TROTTEN drawer unit w 3 drawers on castors assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
All IKEA TROTTEN assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained