Step by StepAssembly Find your furniture

IKEA TROTTEN drawer unit w 3 drawers on castors assembly instructions

How to assemble the IKEA TROTTEN drawer unit w 3 drawers on castors, step by step: 23 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat screwdriver, spanner (included).

IKEA TROTTEN drawer unit w 3 drawers on castors, assembled

A white steel drawer unit on castors: runners screwed to the side panels, two bottom rails that click in, a slide-in back, a hooked-on top, four castors and three drawers, the middle one with a lock. Size: 40x47x56 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Spanner (included).

Based on the official IKEA manual AA-2241545-6 (PDF). Guide updated .

TROTTEN drawer unit w 3 drawers on castors: quick facts
Steps23
Time1–1.5 hours
People1
ToolsPhillips screwdriver, Flat screwdriver, Spanner (included)
Size40x47x56 cm
Official manualAA-2241545-6
IKEA article number804.850.98 (white)
Pieces in the box55

In the box

PartPart numberQuantity
Side panel2
Runner6
Bottom rail2
Back panel1
Top1
Drawer (bottom, 2 sides, back, front, handle)3
Lock 10072577 with keys1
Castor1952744
Screw11258112
Screw11665412
Screw1069174
Screw1050216
Spanner1467141

Steps

  1. Lay out the side panels — Lay both side panels flat on a soft surface with the inside facing up. Turn them so the slot for the top's hooks is at the top edge of each panel: the two panels are mirror images.
  2. Runners on the left side — Put the 3 runners on the inside of the left side panel, roller end at the front edge. Fix each with 2 screws 112581 using a Phillips screwdriver: 6 screws in all. Check: Use the short countersunk screws 112581 here, not 116654 or 106917.
  3. Runners on the right side — Fit the other 3 runners to the right side panel in the same way, roller end at the front, with 6 more screws 112581.
  4. Rear bottom rail — Stand both sides on their rear edges, runners facing each other. Slide the rear bottom rail into the bottom ends of the sides until it clicks, then drive a screw 106917 up through each end of the rail.
  5. Front bottom rail, then stand it up — Slide the front bottom rail into the sides in the same way until it clicks and fix it with 2 screws 106917. Then tip the frame upright onto its bottom edges.
  6. Slide in the back panel — Lower the back panel into the rear edges of the two sides from above and slide it all the way down. Its folded edges must hook over the sides' rear edges, not sit in front of them.
  7. Lock the back panel — With a flat screwdriver, push down the 2 tabs on the top of the rear bottom rail, in front of the back panel, until they lie flat. They lock the bottom of the back panel.
  8. Fit the top — Lower the top onto the unit so its 4 hooks drop into the slots along the top of the sides, then push the top backwards until it stops.
  9. Lock the top — Lay the unit on its back. Inside, at the top front corner of each side, bend the tab over with a flat screwdriver so the top can no longer slide.
  10. Castors in by hand — Turn the unit upside down. Screw a castor 195274 into the hole at each end of the two bottom rails by hand, turning clockwise.
  11. Tighten the castors — Fit the spanner 146714 onto the hex of each castor and tighten it clockwise until it is firm.
  12. Stand it on its castors — Turn the unit over and stand it on its 4 castors.
  13. Drawer: sides onto the bottom — Build the first drawer. Hook a drawer side onto the tabs along each edge of the drawer bottom, runner facing out, and push it back until it locks. Check: Build all 3 drawers the same way (steps 10-15).
  14. Drawer back — Slide the drawer back down into the hooks at the rear ends of the two drawer sides until it rests on the bottom.
  15. Bend the drawer tabs — With a flat screwdriver, bend the tab at the rear end of each side round the back panel, then bend the 2 tabs at the rear edge of the bottom up behind it.
  16. Drawer front — Push the drawer front onto the open end of the drawer so its two brackets slide inside the drawer sides.
  17. Screw the front on — From inside the drawer, drive 2 screws 116654 through each side into the front's bracket: 4 screws in all.
  18. Handle — Set the handle on the top edge of the front with its 2 posts in the holes. From below, inside the front, drive a screw 105021 up into each post.
  19. Build the other 2 drawers — Build the other 2 drawers in the same way (steps 10-15), each with 4 screws 116654 and 2 screws 105021. The front with the lock 10072577 is for the middle drawer.
  20. Top drawer in — Take a drawer without the lock. Line it up in front of the top opening with its runners level with the top pair of runners, slide it in and push the front at its right-hand edge until it closes.
  21. Middle drawer in — Slide the drawer with the lock into the middle opening in the same way and push it closed at the lock.
  22. Bottom drawer in — Slide the last drawer into the bottom opening and push it closed.
  23. Done! — Your TROTTEN drawer unit is ready to roll. The key locks the drawers. Max. load 5 kg per drawer and 20 kg in total.

TROTTEN drawer unit w 3 drawers on castors: questions and answers

How long does it take to assemble the IKEA TROTTEN drawer unit w 3 drawers on castors?

About 1–1.5 hours for 1 person, working through the 23 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the TROTTEN drawer unit w 3 drawers on castors?

Phillips screwdriver, flat screwdriver, spanner (included). Already in the box: Spanner.

Can one person assemble the TROTTEN drawer unit w 3 drawers on castors?

Yes, it is a one-person build.

What size is the TROTTEN drawer unit w 3 drawers on castors once assembled?

40x47x56 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the TROTTEN drawer unit w 3 drawers on castors?

38 fittings of 5 kinds, the most numerous being 12 × screw, 12 × screw, 6 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA TROTTEN drawer unit w 3 drawers on castors assembly instructions PDF?

The official PDF is manual AA-2241545-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 804.850.98 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2241545-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example lock 10072577). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA TROTTEN assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained