IKEA TROTTEN cabinet with sliding doors assembly instructions
How to assemble the IKEA TROTTEN cabinet with sliding doors, step by step: 20 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat screwdriver, Allen key (included), spirit level.
A white steel office cabinet: two leg frames bolted to the bottom panel, side and back panels that slide down into place, a hooked-on top, four shelves on clips and two lockable sliding doors. Size: 80x55x110 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Allen key (included), Spirit level.
Based on the official IKEA manual AA-2241620-2 (PDF). Guide updated .
| Steps | 20 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat screwdriver, Allen key (included), Spirit level |
| Size | 80x55x110 cm |
| Official manual | AA-2241620-2 |
| IKEA article number | 604.747.60 (white) |
| Pieces in the box | 55 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Leg frame (rail + 2 legs) | 2 | |
| Bottom panel | 1 | |
| Side panel | 2 | |
| Back panel | 2 | |
| Top | 1 | |
| Shelf | 4 | |
| Sliding door with lock (key included) | 1 | |
| Sliding door without lock | 1 | |
| Levelling foot | 10036516 | 4 |
| Bolt | 10073004 | 4 |
| Screw | 100404 | 4 |
| Screw | 106917 | 10 |
| Shelf clip | 114594 | 16 |
| Bumper | 123805 | 2 |
| Allen key | 130445 | 1 |
Steps
- Feet into the leg frames — Stand both leg frames upside down. Screw a levelling foot 10036516 into the end of each of the 4 legs by hand, clockwise, until it is snug.
- Bottom panel between the frames — Lay one leg frame flat, brackets up. Lower the bottom panel onto it so both brackets slide into the panel ends. Then put the second frame on top, brackets down into the other end.
- Bolt the frames on — Push a bolt 10073004 into each of the 4 holes at the panel ends and tighten it into the bracket with the Allen key.
- Stand it up, add the sides — Stand the base on its feet. Slide the left side panel down over the two left leg ends until it sits on the frame, then do the same with the right side panel.
- Back panels — For a free-standing cabinet, turn the smooth side of the back panels outwards. Slide the lower back panel down between the sides all the way to the bottom, then slide the upper panel down onto it. Check: Against a wall you may turn the smooth side inwards instead (manual page 6, right).
- Lock the back panels — At the joint between the two back panels, push the 2 small tabs down into their slots with a flat screwdriver. This locks the panels together.
- Screw the back panels on — From inside the cabinet, drive 4 screws 106917 through the edge of the back panels into the left side, then 4 into the right side, with a Phillips screwdriver.
- Fit the top — Lay the top on the cabinet so its 4 hooks drop into the slots at the top of the sides, then push the top backwards until it stops.
- Screw the top on — From inside the cabinet, drive 4 screws 100404 up into the top, one near each corner, with a Phillips screwdriver.
- Shelf clips — Hook 8 shelf clips 114594 into the slotted strips on each side, at two heights: tip each clip in at the top and press it down until it locks. All 4 clips for a shelf must be level.
- Back shelves — Put a shelf on the rear clips at each height: hold it level just above them, push it to the back and lower it onto the 4 clips.
- Front shelves — Put the other 2 shelves on the front clips in the same way, in front of the back shelves.
- Hang the plain door — Take the door without the lock. Tip its top towards you, set both rollers into the rear groove of the bottom track, then swing the door upright. Check: The door without the lock goes in the rear track first.
- Lock the top guides — Push both guides on the top edge of the door up into the top track until they click.
- Slide the door right — Slide the door all the way to the right.
- Bumpers on the lock door — Lay the door with the lock face down on a soft surface. At the top and bottom of its handle edge, put on a bumper 123805 and screw it down with a screw 106917.
- Hang the lock door — Lift the lock door, tip its top towards you and set both rollers into the front groove of the bottom track, on the left. Swing it upright.
- Lock its top guides — Push both guides on the top edge of the lock door up into the top track until they click.
- Level the cabinet — Put a spirit level on the top. Turn the 4 feet in or out until the cabinet stands level, side to side and front to back.
- Done! — Your TROTTEN cabinet is ready. If the doors are not straight, adjust the height at each roller with a Phillips screwdriver (manual page 16). The key locks the left door.
TROTTEN cabinet with sliding doors: questions and answers
How long does it take to assemble the IKEA TROTTEN cabinet with sliding doors?
About 1–1.5 hours for 1 person, working through the 20 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TROTTEN cabinet with sliding doors?
Phillips screwdriver, flat screwdriver, Allen key (included), spirit level. Already in the box: Allen key.
Can one person assemble the TROTTEN cabinet with sliding doors?
Yes, it is a one-person build.
What size is the TROTTEN cabinet with sliding doors once assembled?
80x55x110 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the TROTTEN cabinet with sliding doors?
40 fittings of 6 kinds, the most numerous being 16 × shelf clip, 10 × screw, 4 × levelling foot. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TROTTEN cabinet with sliding doors assembly instructions PDF?
The official PDF is manual AA-2241620-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.747.60 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2241620-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example levelling foot 10036516). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TROTTEN drawer unit w 3 drawers on castors assembly instructions
- IKEA TROTTEN cabinet with doors assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
All IKEA TROTTEN assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained