IKEA VIKHAMMER bedside table assembly instructions
How to assemble the IKEA VIKHAMMER bedside table (nightstand), step by step: 18 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver, hammer, Allen keys (included).
A white VIKHAMMER bedside table: a cam-lock box built upside down, a steel leg frame bolted on, and a drawer on full-extension runners above an open shelf. Size: 40x39x65 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Allen keys (included).
Based on the official IKEA manual AA-2536116-1 (PDF). Guide updated .
| Steps | 18 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Hammer, Allen keys (included) |
| Size | 40x39x65 cm |
| Official manual | AA-2536116-1 |
| IKEA article number | 003.817.64 (white) |
| Pieces in the box | 63 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Top panel | 1 | |
| Bottom panel (with 4 screw holes) | 1 | |
| Side panel | 2 | |
| Back panel | 1 | |
| U-shaped leg frame | 2 | |
| Base frame | 1 | |
| Drawer front | 1 | |
| Drawer side | 2 | |
| Drawer back | 1 | |
| Drawer bottom | 1 | |
| Drawer runner | 190372 | 1 |
| Drawer runner | 190373 | 1 |
| Screw | 108462 | 4 |
| Wooden dowel | 101350 | 8 |
| Cam screw | 118331 | 8 |
| Cam lock 119030/117434 | 8 | |
| Screw | 100214 | 4 |
| Bolt | 100181 | 4 |
| Cap | 192805 | 4 |
| Expansion nail | 110519 | 4 |
| Lock clip | 124218 | 2 |
| Allen key | 100001 | 1 |
| Allen key | 100002 | 1 |
Steps
- Cam screws into the top — The box is built upside down. Lay the top panel face down on a soft surface; it is the panel without screw holes on its face. Screw 4 cam screws 118331 into the holes near its corners. Check: The panel with 4 small holes on its face is the bottom panel: keep it for step 7.
- Runners on the side panels — Lay both side panels flat, inside facing up. Lay a drawer runner on each panel, its hooked end at the grooved back edge, and fix each one with 2 screws 108462. Check: The two runners are different: 190373 goes on one panel and 190372 on the other, both with the hook at the back edge.
- Side panels onto the top — Push 4 dowels 101350 into the holes along the side edges of the top. Stand both side panels on the top, runners towards the top and grooves at the back, over the dowels and cam screws.
- Lock the side panels — Put 4 cam locks 119030/117434 into the holes on the inside of the side panels, next to the top, and turn each one clockwise with a flat screwdriver until it grips the cam screw.
- Back panel — Slide the back panel down the grooves at the back of the side panels until it sits in the groove in the top.
- Dowels in the side panels — Push 4 dowels 101350 into the holes in the free edges of the side panels, 2 in each.
- Bottom panel on — Press the bottom panel onto the dowels, with its 4 screw holes facing up and the groove over the back panel.
- Leg frames — Lay the 2 U-shaped leg frames on the bottom panel, legs up, one along each side. Fix each with 2 screws 100214 through the holes in its channel, using Allen key 100001.
- Base frame — Set the base frame on the ends of the 4 legs and bolt it on with 4 bolts 100181, using Allen key 100002. Check: Each corner of the base frame must be flush with the outside of its leg, not overhanging.
- Caps, then turn it over — Press 4 caps 192805 into the holes in the corners of the base frame. Then turn the table the right way up and stand it on its frame.
- Cam screws into the drawer front — Now the drawer. Lay the drawer front face down, its groove facing up, and screw 4 cam screws 118331 into the holes on the inside, 2 at each end.
- Drawer sides onto the front — Stand the 2 drawer sides on the front, grooves facing in and cam lock holes facing out, and press them down over the cam screws.
- Lock the drawer sides — Put 4 cam locks 119030/117434 into the holes on the outside of the drawer sides, next to the front, and turn each one clockwise to lock.
- Slide in the drawer bottom — Slide the drawer bottom down the grooves in the sides from the open end until it sits in the groove of the front.
- Drawer back — Lay the drawer back on the ends of the sides. Set 4 expansion nails 110519 in its holes and hammer them in, with a scrap of wood between hammer and nails. Check: Hit the wooden block, not the nails, so the heads are not damaged.
- Lock clips under the drawer — Turn the drawer round so its underside faces you. Twist a lock clip 124218 into the hole in the bottom edge of each side, next to the front.
- Put the drawer in — Pull both runners out. Hold the drawer level in front of the opening, slide it back over the runners and set it down so the hooks at the back catch. Push it in; the clips lock onto the runners. Check: To take the drawer out again, press the levers of the 2 clips under the front.
- Done! — Your VIKHAMMER bedside table is finished. The drawer runs on full-extension runners; the open shelf below is for books and a charger.
VIKHAMMER bedside table: questions and answers
How long does it take to assemble the IKEA VIKHAMMER bedside table?
About 1–1.5 hours for 1 person, working through the 18 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the VIKHAMMER bedside table?
Phillips screwdriver, flat-blade screwdriver, hammer, Allen keys (included). Already in the box: Allen keys.
Can one person assemble the VIKHAMMER bedside table?
Yes, it is a one-person build.
What size is the VIKHAMMER bedside table once assembled?
40x39x65 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the VIKHAMMER bedside table?
48 fittings of 11 kinds, the most numerous being 8 × wooden dowel, 8 × cam screw, 8 × cam lock 119030/117434. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA VIKHAMMER bedside table assembly instructions PDF?
The official PDF is manual AA-2536116-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 003.817.64 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2536116-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner 190372). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
- IKEA STORKLINTA chest of 2 drawers assembly instructions
All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained