Step by StepAssembly Find your furniture

IKEA SNIGLAR cot assembly instructions

How to assemble the IKEA SNIGLAR cot, step by step: 14 animated steps built from the official manual, about 30–45 min for 1 person, with flat-blade screwdriver, Allen key (included).

IKEA SNIGLAR cot, assembled

Solid beech cot for a 60x120 cm mattress: two barred end panels with legs, two barred sides and a base that sits at two heights. Size: 60x120 cm. About 30–45 min, 1 person. Tools: Flat-blade screwdriver, Allen key (included).

Based on the official IKEA manual AA-719994-5 (PDF). Guide updated .

SNIGLAR cot: quick facts
Steps14
Time30–45 min
People1
ToolsFlat-blade screwdriver, Allen key (included)
Size60x120 cm
Official manualAA-719994-5
IKEA article number302.485.37 (beech)
Pieces in the box30

In the box

PartPart numberQuantity
End panel with legs2
Side panel2
Base1
Bolt1237568
Cross dowel1211148
Bolt1486244
Base pin100507974
Allen key1000011

Steps

  1. Sides against the first end — Stand one end panel up and hold both side panels against its posts. Push a cross dowel (121114) into the hole near the end of each side rail: from below in the top rails, from above in the bottom rails. 4 in all. Check: Keep the end panel the way round the drawing shows: the small holes in its posts (marked by the hand) take the base pins later.
  2. Bolt the sides on — Turn each cross dowel with a flat screwdriver until its threaded hole faces the post. Then screw a bolt (123756) through each post hole into the dowel with the allen key, 4 in all.
  3. Pins into the base — Lay the base flat with its label facing up. At each corner block push an L-shaped pin (10050797) up into the hole from below, then screw a bolt (148624) into it from above with the allen key. Leave the pin arms pointing out past the ends of the base. 4 in all. Check: Each corner block must sit flush with the side of the base, as in the right-hand close-up, not turned out.
  4. Turn over and fit the base — Turn the frame over so it stands on the end panel. Slide the base in between the sides, board side towards the top rails, and lower it to push its two bottom pins into the upper holes in the end posts (newborn height). Use the lower holes once your baby can stand.
  5. Second end on top — Put the second end panel on top so the two base pins go into the holes in its posts. Push a cross dowel (121114) into each side rail end below it, as in step 1.
  6. Bolt the second end on — Line the cross dowels up with the screwdriver, then screw 4 bolts (123756) down through the end posts into them with the allen key.
  7. Stand the cot up — Tip the cot back onto its four legs. The base is at the upper height, for a newborn.
  8. Later: undo the top bolts — To lower the base once your baby can stand, lay the cot on its end again. Undo the 4 bolts in the top end panel with the allen key.
  9. Later: take the top end off — Push the 4 cross dowels out of the side rails with the screwdriver, then lift the end panel up off the base pins.
  10. Later: base into the lower holes — Lift the base up out of the end panel on the floor and lower it again with its two pins in the lower holes of the end posts.
  11. Later: refit the top end — Put the end panel back on top, with the base pins in its post holes. Push the 4 cross dowels back into the side rails.
  12. Later: bolt it back on — Line the cross dowels up with the screwdriver and screw the 4 bolts (123756) back in with the allen key.
  13. Stand it up again — Stand the cot back on its legs, now with the base at the lower height.
  14. Done! — Your SNIGLAR cot is assembled. Use the upper base height for a newborn and move the base to the lower holes as soon as your baby can sit or pull up to stand.

SNIGLAR cot: questions and answers

How long does it take to assemble the IKEA SNIGLAR cot?

About 30–45 min for 1 person, working through the 14 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the SNIGLAR cot?

Flat-blade screwdriver, Allen key (included). Already in the box: Allen key.

Can one person assemble the SNIGLAR cot?

Yes, it is a one-person build.

What size is the SNIGLAR cot once assembled?

60x120 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the SNIGLAR cot?

24 fittings of 4 kinds, the most numerous being 8 × bolt, 8 × cross dowel, 4 × bolt. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA SNIGLAR cot assembly instructions PDF?

The official PDF is manual AA-719994-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 302.485.37 (beech); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-719994-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 123756). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA SNIGLAR assembly guides · All beds assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained